Cisco Switches :: Does The SF300 Support Stacking
Jul 20, 2012Does the SF300 support stacking? If it does, which port(s) are the ideal ones?
View 1 Replies
ADVERTISEMENT
Cisco Switches :: Can SF300-24P Support POE On All Ports
Jun 18, 2012An end user is looking to connect 21x IP Cameras to the switch and they require at least 6W port port. Now, the datasheet states that each port on the SF300 provides 15.4W.I need to double check so that the end user will not start connecting the IP Cameras and then half of them might not fire up.
View 1 Replies View RelatedCisco Switches :: Getting Better Ssh Shell Support On The SF300?
Sep 9, 2012Any chance of getting better ssh shell support on the SF300?Being able to do things like this are very useful:
ssh 10.1.1.1 "sh version"
ssh 10.1.1.1 "sh run"
Cisco Switches :: SF300 Does Not Support Complete DHCP?
Apr 5, 2013I have some issue from last 2 month on sf300.
The problem is that sf300 does not support complete dhcp, for that i put different internet modem.
I connected one internet modem in vlan 1 so users from that vlan can access internet and default gateway is nothing but Internet modem ip. user in the vlan are not communicate with other vlan because, other vlan users default gateway is Interface ip address. How i can give access to vlan 1 to access other vlan .
See the attached.
I have to used static route in all 3 devices or any one.
CIsco Switches :: SGE-2010 How To Wire Switches For Stacking
Dec 13, 2011We had a SGE-2010, just purchased 2 (two) SGE-2010P. I want to stack the switches (all 3) (unless there is a better way). Not sure what is needed hardware wise, and how to physically wire the switches. Had switches years ago (diff brand) that used a special cable that connected the switches. It seems that is not the case here. I have not used fiber in networking before so I am new to that part, I’m willing to learn, just need pointed in the right direction.Can all three switches be stacked, (1) SGE-2010 & (2) SGE-2010P? I THINK I need to use the GBIC port 4 to stack, I understand 1 port is enough if two switches are used, but what about three or more switches.What are the other GBIC ports used for? Will I be better off (can I ) use the GBIC ports LAG (2 ports) to the other switches? Or would regular ports work just as well?
View 6 Replies View RelatedCisco Switches :: How To Config VLAN On 2 Switches SF300-24 Layer 3
Oct 6, 2011now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedCisco Switches :: Retrieving ARP Table From SF300 Switches Using SNMP?
May 22, 2012I'm setting up an SNMP poller to retrieve the ARP table (ipNetToMediaPhysAddress) from my SF300 switches. I can retrieve the table from SF300-24P and SF300-48P switches running Firmware Version 1.0.0.27, but get garbage for the MAC address when retrieving that same table on the same model switches running Firmware Version 1.1.1.8. Is there an outstanding defect on this code level? How can I retrieve the table showing the IP address to MAC address mappings?
View 1 Replies View RelatedCisco WAN :: Stacking Switches 2960S
Apr 7, 2012Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.
They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[Code]....
Cisco Switches :: Stacking Requirements For SG500-52P
Jun 4, 2013I have a Cisco SG500-52P along with an older SGE-2010P, am I correct that in order to stack they must be the same series?
View 1 Replies View RelatedCisco Switches :: SGE2010 Stacking Compatibility With SG500
May 29, 2013I am currently running two SGE2010 in stack and planning to purchase new Sg500 .I have two questions :
1. If these two different products can be managed as one stack.
2. Are the SFP (mini-GBIC) connections compatible and if so what accessories or parts do we need to enable them?
Cisco Switches :: SG500X-58 - Native Stacking Mode?
Mar 15, 2013The switch SG500X-48 has 4 SFP+ ( 10G ) ports - XG1, XG2, XG3/S1, XG4/S2 - and two configuration modes - standalone and "native stacking".
Can I use XG1 and XG2 SFP+ ports to connect servers when "Native stacking" mode is active ?
Cisco Switches :: SG300 Unit In Stacking Mode?
Nov 7, 2011So it seems like the SG300 series (have here sg300-52) can be run as standalone unit and also in stacking mode. but i can not find any documentation or howto for this.
View 8 Replies View RelatedCisco Switches :: SF300 Phones Not Getting IP
Jun 14, 2011I have a new install with 3 SF300 switches, setup as vlan 2, the switch connected directly to the 2901 router has no problems, plug in a phone and it gets an IP, but if connected to either of the two swtiches behind the first switch, they do not get an IP. I am seeing the DHCP request hitting the router, and the router sending the IP to the phone, but it never gets the IP.
*Jun 15 10:40:20.040: DHCPD: client's VPN is .
*Jun 15 10:40:20.040: DHCPD: Sending notification of DISCOVER:
*Jun 15 10:40:20.040: DHCPD: htype 1 chaddr 40f4.ecef.bded
[Code]....
All ports are setup as trunk on vlan 2 including the ports that connect the switches together. Not sure what the problem is, but they are going live tomorrow and only have 48 out of 120 phones.
Cisco Switches :: SG300 Stacking And Powered From POE By Upstream Switch?
Sep 11, 2012I discovered on a pair of SG300-28P.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
Cisco Switches :: SGE2010 Stacking Versus Link Aggregation?
Aug 14, 2011answer regarding stacking the SGE2010 switches versus link aggregation if greater than 1 Gb connectivity is required between individual switches? Currently have several switches in a stack configuration but would like to increase the bandwidth between some or all of the switches. Does stacking support a link aggregation configuration? If so what ports can be used and how should the link aggregation be configured in conjunction with the stacking?
View 2 Replies View RelatedCisco Switching/Routing :: Stacking 2960S Switches Options?
Oct 10, 2012I have 2 Catalyst 2960S (24 ports and 48 ports). Can I stack them using the Uplink connection instead of the stack modules. I know Stack module is the best option but it is kind of expensives (half price of the 24 ports switch) and I only need to stack no more then 2 switches.
View 4 Replies View RelatedCisco Switches :: SG500X-24 Stacking - Keeping Connections Active
May 12, 2013I am installing a network that has two SG500X-24 switches as core and several SG300-52 switches as access switches. I've seen in the SG500X-24 datasheet that there is a True Stacking feature. But in the data sheet there are not a lot of details about it. My doubt is the following. If I configure the two SG500X-24 switches as a single switch through stacking them, can I connect one SG300-52 switch to these two SG500X-24 switches through two cables (both configured as a LAG in the SG300-52 and in the SG500X-24 stack, one cable per SG500X-24), the the first cable connected to the first SG500X-24 switch and the second cable connected to the second SG500X-24 switch and keep both connections active?
View 3 Replies View RelatedCisco Switches :: Cannot Access VLANS On SF300 24 Over QnQ
Jan 30, 2012Trunk from 3500 going into SF300-8 #1 QNQTrunk from SF300-8 #1 going into trunk SF300-8 #2QNQ from SF300-08#2 going into Trunk SF300-24, All Vlans from Network 1 seem to be communicating properly between the 3550 and SF300-24 and is isolated from the Transport Network by QnQ. I am having one problem, I can not ping the SF300-24 or get to the management interface. I am able to access other devices on the SF300-24 Vlan1 from devices on the 3550 Vlan1 and vice versa.
View 1 Replies View RelatedCisco Switches :: SF300 Does Not Receive IP Address
May 21, 2013cisco 2811 - DHCP server..If IP Phone 3905 installed in SF 300 he does not receive an ip address. [code] If IP Phone 3905 installed in the Catalyst 2960 - all OK.
View 7 Replies View RelatedCisco Switches :: IP Phone Config On SF300-24P
Mar 26, 2013I'm playing with an SF300-24P switch and want to connect an IP Phone. I'm more familar with IOS syntax than the SF300 GUI.
How would I replicate the following in the SF300:
Switch(config)#int fa0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(Config-if)# switchport voice vlan 5
Not sure if setting the port to an ACCESS port on VLAN 15 (i.e. 15UP) and having the Voice VLAN set to 5 is correct.
Or should the port be set to General or Trunk with 15 as the untagged VLAN and 5 as the tagged voice VLAN (i.e. 15UP, 5T)?
Cisco Switches :: SF300-08 - Possible To Have 2 Networks On Different VLANs
May 22, 2011My ISP is providing me with 1 public IP on a /30 network and 14 public IPs on a /28 network. In this example the 10.0.0.1 is the default gw provided by my ISP and 10.0.0.2 is my SF300-08. If I setup my router to route to 10.0.0.2 as the default gw through the interface between the switch and router, can I configure the static routes in the switch to route further to 10.0.0.1?
is it possible to have these 2 networks on different VLANs and configure inter-VLAN routing? I don't want the switch accessible from the 10.0.0.2 IP.
Cisco Switches :: SF300 24p Connection With Vlan
Oct 17, 2012In my network I got 3 SF300 24 p switches. I managed vlan 10 for data and it is also a native vlan and vlan 20 for voice ,1st switch is the core switch and im having a problem in connecting them ?
View 7 Replies View RelatedCisco Switches :: SF300-48 Cannot Communicate With VLan 2
Jan 2, 2013my new Cisco SF300-48. I want to create 2 vlan (vlan 1 & vlan 2). The switch is set at layer 2. example : vlan 1 (port 1, 2, 3) , vlan 2 (port 4, 5, 6) vlan 1 can communicate each other (port 1, 2, 3) and vlan 2 can communicate each other (port 4, 5, 6)But vlan 1 cannot communicate with vlan 2.
View 4 Replies View RelatedCisco Switches :: IP Routing VLAN On SF300-24?
Apr 22, 2011I had made a DHCP server that had many scope:
1- scope: 192.168.1.208/28
2- scope: 192.168.1.224/28
3- scope: 192.168.16.0/24
[Code]....
How to condig SF300-24 to vlan 2 vlan 3 can get IP address from DHCP server in VLan 4?
Cisco Switches :: SF300-24p - How To Restore Password
Nov 17, 2012We have a mitel 3300 PBX that is our DHCP server. It feeds an old Foundry Networks switch that nobody knows the password for anymore so I can't even look in it to get some clues. What I think I know is this.
vlan1 = PC's subnet 10.0.0.X 255.255.255.0
vlan2 = phones subnet 10.1.0.X 255.255.255.0
Phones plug into the switch, PC's plug into the phone.
I am assuming this to be the case becase all the PC's get those numbers and when booting up a phone it comes up and says "vlan2 pri 5" during the DHCP discovery.
Like I said the Mitel 3300 is the DHCP server and our internet access is from the firewall's trusted port.
I have put the switch in L3 mode via the console. No matter what I try, the PC will always get IP addresses in vlan2's subnet. Even if I plug the PC directly into the switch.
I have factory reset this baby and all I have done at this point is put it back in L3 and changed the default ip address so I can get to the web GUI.
Cisco Switches :: SF300-24P Technical Specifications
Mar 10, 2013I am looking for some technical specs on the SF300 series which I can't seem to find in the 300 series data sheet: the maximum delay for traffic through the switchbuffer size for each switchportwhether or not the ports are suitable for shielded cable and connectors
View 4 Replies View RelatedCisco Switches :: SF300-48P Option To Telnet It
Jan 14, 2012I have sf300, i didn't found the option to telnet it. default IP of the switch is 192.168.1.254, i can access it by HTTP.
also i'm not able to attach IP phone on voice vlan & computer on vlan 1 ,please share the step by step guide how to access the switch by telnet.
& how to make voice vlan 2 for IP Phones & Vlan 1 for PC.
Cisco Switching/Routing :: 3750X Setting Up Power Stacking Switches
Dec 27, 2012I'm trying to get some clarity on power stacking 3750X switches. I have a new stack of 6 switches. I know I can only have 4 in a power stack and all 6 in the data stack with a max of 8. I'm trying to find the proper way to connect the power stack cables for the 4 switch power stack.
View 1 Replies View RelatedCisco Switching/Routing :: Stacking 24 And 48 Port 3750X Switches Not Working?
Dec 11, 2012We purchased a number of 3750X 48 and 24 port switches for the College Campus. Am finally getting around to getting them inserted on the network. Working with a WS-3750X-48PF-S and a WS-3750X-24P-L. Have them stacked with the 10Gb uplink on the 48 port switch. Have not been having fun.In the boot sequence, the switches recognize they are stacked, but as soon as they finish boot, I get the message on the 48 port switch: “Stack Port 1 Switch 1 has changed to state down.” Then “Stack Port 2 Switch1 has changed to state down.” Am noticing that I have a message preceding that: “Major version mismatch with stack neighbor.”The 48 port is running c3750e-universalk9-mz.150-1.SE3, HBOOT 12.2(53r)SE2.The 24 port is running c3750e-unversalk9-mz.122-55.SE3, HBOOT 12.2(53r)SE2Most of our 3750X and older switches are running 122-55 or 122.58 code. IP base or Universal. There is speculation that the problem is the 24 Port is Lan base, as the part number might indicate. (WS-C3750X-24-P-L.... I think that is the part number) and the 48 is IP base. Both switches are Universal, and my understanding is that they don't care about LAN or IP Base until you enable a function that falls in the IP Base domain. Then I have to call Cisco Licensing.For these switches, LAN Base is fine, based on the boot message, I feel the real problem is 122-55 versus 150-1 in the stack. So.. the question is: Do I downgrade the 48 port to match what we have in our environment, and what is on the 24 port switch. Or... Upgrade the 24 port switch to match the 48 port switch and have an installation that is not consistent with our environment? I do have two more edge closets to install with this purchase of 3750X 48 port switches.
View 2 Replies View RelatedCisco Switching/Routing :: 3750X - 48PS Switches Power Stacking
Mar 28, 2012In my office we bought 7 cisco 3750X - 48PS switches. We configured Data Stacking between those switches. We also want to configure Power Stacking between those 7 devices.
I found in the Data Sheet that we can only configure 4 devices in power stacking at a time. If it is like that how to configure the rest of 3 devices. Need configuring power stacking between those devices in a better way..
power stack cable part no we have is
CAB-SPWR-30CM
Cisco Switches :: Sf300-08 When Get To Login Screen / Can't Type Anything
Jul 13, 2012After finishing all of my projects here at work, I decided to finally take a look at a sf300-08 that was left by my predecessor. I almost got into it once via browser but the UI crashed. So I downloaded the manual and proceeded to connect to the switch via rs-232. When I get to the log in screen I cant type anything in and when I try hypterterminal crashes.
View 5 Replies View RelatedCisco Switches :: Sf300-24p System Light Flashing?
Mar 14, 2013I changed the setting from static to dynamic and the switch froze up. all lights on the panel flashed, when they stopped the system light on the left side continued to flash. I tryied unplugging unit as well as depressing the reset for longer than 30 seconds. Unit still the same.
View 8 Replies View RelatedCisco Switches :: SF300-24 Is Not Saving Configuration After Reboot?
May 3, 2011I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies View Related