Cisco Wireless :: WAP4410N Will Not Stay Powered On 3550 PoE
Oct 13, 2010
I have a WAP4410N new out of the box will not stay powered on any of our three 3550 24 port PoE switches running 12.2(25) ipservicesk9-M EMI. The WAP4410N is running the 2.0.3.3 firmware. Unfortunately the AP is the only PoE device I have at my disposal. The device will power on, the link will come up on the switch but after ~5 seconds the power light then the PoE light on the WAP4410N turns off and the device reboots and continues this cycle. The WAP4410N operates normally when plugged in with the included power adapter, but I need to use this as a PoE device.
View 9 Replies
ADVERTISEMENT
Jul 10, 2010
There is a discussion of this going back many months in the previous forum. My initial post there has had over 600 views and I see that an IT administrator with 10 BB has the exact same problem. I have replaced my BB 4 times and all of them behaved the same way with this CISCO WAP4410N:
THE PROBLEM: The 4410 drops the WiFi connection to a Bold 9700 BB (using WAP2). I got an old Motorola about 6 years old out and found it works fine with the BB as does most of the public hot spots. This is an issue with the 4410. An IT Admin has found (an posted in the eariler forum) that for some reason the key change is not accomplished when issued by the 4410 but it works for others. The Admin discovered that if he set the timout on the key change to maximum he only has to restart the 4410s every 10 days.
So I have the 4410 for my 5 computers with which it works fine and beside it the old Motorola for the BB.
When I called support about this I was told that "we don't support connections to Blackberry." I hate to have to sell this thing on Ebay and buy another brand becuase of this. Seems that Cisco would fix it.
View 1 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Feb 19, 2013
I've had this router for just over a year now so the warranty is out and it just so happened to stop functioning last night. I'm fairly decent in the router world since I am studying for my CCNA, so I have tried just about anything imaginable. I woke up this morning with no connection, checked the modem, then the router. The router was powered on, but the up/downstream lights were not doing a thing. The modem is not the issue (I am hardwired as of now). I have tried both resets, including unplugging the device, and still can't get a response out of it. The logo light will turn straight on (no fad in and out like it's suppose to) and then it does absolutely nothing. I have never encountered this sort of problem on a home router before. I can't login to the router either.
View 5 Replies
View Related
Jan 24, 2013
Background info:
Comcast cable internet and TV
Regular modem
Linksys WRT54G router
Windows7 desktop
The problem I'm seeing is that our wireless connection cuts out about 5 minutes after turning on our main desktop. Turn off the main desktop and wireless begins to work again. Throughout all of this, the wired connection works fine, and I have no problem connecting to the router either.
View 1 Replies
View Related
Aug 23, 2011
I recently upgraded my WRT610N to Firmware Version: 2.00.01 and now the unit powers down on its own after a few hours. Are there any known issues with this firmware?Is there any way to roll back to the previous version of the firmware?
View 4 Replies
View Related
Nov 9, 2011
My wrt110 firmware .05 has been working fine until now. I have a couple of phones, 2 printers, 3 laptops and a wii happily connecting to it. However now when I power on the wireless device, nothing can connect wirelessly. Wired connection is fine, but my wireless network disappears. No device can find the network, although it is there and set up on the admin pages. I pull the power chord out for 30 seconds and try again to get it going again, a bit like trying to start a car. Everntually devices find the network.
On two occasions it has forgotten the wireless settings and restored an open 'linksys' network. It's really infuriating becuase whilst I restore the SSID and use the same key, not all the devices actually recognise it and have to be reconfigured on the devices.
View 5 Replies
View Related
Jun 7, 2011
I have a question on 300 series PoE switch (SRW224G4P, power budget: 180W). How many WAP 4410N can be powered by this switch??How many AP 1242 can be powered by this switch? Since CDP is not supported yet, I think switch will provide 15.4W power for each AP. So each switch can power up to 11 WAP4410N or AP 1242. Is this correct??
One other quesiton is When CDP is supported, can I calculate as below? WAP4410N (Power draw:10.1W): 180/10.1W = 17.xx -> Up to 17 WAP4410N can be powerd AP1242 (Power draw:12.4W): 180/12.4W = 14.xx -> Up to 14 WAP4410N can be powerd
View 1 Replies
View Related
Dec 3, 2012
I have a DIR-615 router (h/w ver E4 and firmware 5.10) that needs to be powered off and then on again several times in a day (a reset of sorts).After being on for sometime, most devices lose connectivity to the router and new devices cannot connect to it.After being powered off and then on again, everything works fine.
View 4 Replies
View Related
Nov 1, 2011
3502i's LED light turn white? Ifso, what does it mean? The info on the LED lights does not mention white. The serial port and the data port are non responsive, but the unit stays powered over PoE.
View 22 Replies
View Related
Jul 15, 2011
I'm having trouble getting my evga 680i to wake on lan from a powered off state. I've done it before but for some reason now it doesn't seem to work. I have formatted since the last time I used wake on lan.
I've got all the settings right in the bios and everything. WOL is enabled in the networking properties on the adapter and in the bios. I can wake from a sleep or hibernate state - just not powered off. Using a WOL test client it confirms it is receiving the magic packet.
When my comp is off I dont see the network port light up with the LEDs. I imagine this has something to do with it -- i just dont know what had to go to power management on the configure tab of my network adapter and uncheck the box "allow windows to power off this device to save power" even though I also had under that checkbox "allow wake on lan" checked.
View 3 Replies
View Related
Sep 11, 2012
I discovered on a pair of SG300-28P.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
View 2 Replies
View Related
May 19, 2012
I have a 6509 that has dual SUP32's.Just want to make sure and give a reason(if there is one). Slot 6 always becomes the active hot on a full reboot. Meaning from no power to the whole switch to powered on. What is the election process for Supervisors?
View 5 Replies
View Related
Feb 28, 2011
i did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
View 4 Replies
View Related
Nov 17, 2011
We just recently signed up with Time Warner Cable for internet access. The modem they gave us is also a wireless router. So we set up our wireless network like we should but for some reason my desktop computer won't stay connected to the new wireless network. We have a laptop downstairs that doesn't have any problem staying connected. I can connect to the neighbors wireless network and I have no problems staying connected. I can't figure out why my desktop won't stay connected to our network
[code]....
View 13 Replies
View Related
Jun 18, 2012
I received my new XPS 15 yesterday and it will connect to the wireless for a minute or two, then it is gone! I have 3 other computers on the network, so my internet/router is fine. Dell support tried to remotely fix it for a couple of hours last night.
View 8 Replies
View Related
Mar 6, 2012
My DIR-825 stays on even when I flick the power switch, for as long as I don't disconnect the externally powered Belkin USB hub from it. Some lights do come off, Internet light turns orange, but it stays on. If I disconnect the hub before trying to shut down the router, it turns off instantly.
I feel slightly worried by this because as far as I am aware, a USB client device shouldn't be feeding power to the host. On the other hand, the host shouldn't be accepting power from the client either.
Also, sometimes after days since last reboot, the USB light on the router is not on despite connected devices, and they may or may not appear in Shareport.
View 3 Replies
View Related
Apr 17, 2011
It took a while but I've had my 1522 running well for several days. However, if I power down and then power up the 1522, it never reconnects. The bridge mode light flashes 5 times, then - nothing.
So, I have to disconnect everything, bring the 1522 back to my main PC, attach it, let it connect properly, then unattach and re-attach at it's use site.
(I'm using a static IP address and a Cisco E3000 router working perfectly with all my other stuff. Firmware v1.31)
View 1 Replies
View Related
Feb 21, 2012
I have multiple 1230AG wireless access point in autonomous mode that I am migrating to lightweight mode so that a 4402 controller can manage them. I already migrated 4 of those APs with no problems using the Upgrade Tool version 3.4 and now I have one that just refused to upgrade version.
I ran the upgrade tool for this AP alone with the same parameters as others. It is now on lightweight version 12.3.7-JX9 The upgrade procedure went smoothly, the SSC was created on the AP and added to the authorised list on the controller. The AP boots up, gets an IP by DHCP, tries the controller via DNS, gets to it. It joins it then disconnects. Its FastEthernet interface keeps doing down/up every 90 seconds or so.
In my controller logs I see:
*SNMPTask: Feb 22 19:39:17.135: %LWAPP-3-INVALID_SLOT: spam_api.c:711 Invalid slot identifier (0) - ; AP 00:13:.........
*spamReceiveTask: Feb 22 19:39:13.150: %LWAPP-3-PAYLOAD_MISSING:
[Code].....
View 5 Replies
View Related
Jun 4, 2013
One of our Nexus 7000 modules failed and generated the status below. Could this possibly be a hardware issue?
# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 10 Gbps Ethernet XL Module powered-dn
Mod Power-Status Reason
--- ------------ ---------------------------
1 powered-dn Unable to power up card (Power_OK not set)
View 4 Replies
View Related
Dec 30, 2011
I have a dell inspiron laptop that is about 5 years old. It runs Windows XP and works great. Lately though it will not stay connected to my network (Linksys Router). It will connect and disconnect several times per hour and this evening it connected/disconnected and would not connect again.
View 14 Replies
View Related
Apr 28, 2012
my wireless connects perfectly but within a minute disconnects for no reason
View 1 Replies
View Related
Dec 11, 2011
My wireless connection won't stay connected for more the a few seconds, and it will keep trying to re-connect, then connect and then disconnect.It's not the router as I have another laptop that connects just fine
View 5 Replies
View Related
Feb 3, 2012
I'm having trouble getting my laptop to stay connected to my wireless internet. This problem only occurs with my laptop. Other laptops in the house are able to connect no problem. It stays connected for about 5 minutes at a time, then loses connection. I have to disconnect and then reconnect all the time just to get online. I've had the router about 2 years with no problems. This just started happening only to my laptop yesterday.
View 7 Replies
View Related
Jan 29, 2013
When we first bought the computer, it worked fine but we sent it with my oldest sister to college and she messed it up. Since she brought it back, it will not stay connected to our home wireless network. It will stay connected for about an hour and then it will quit and then the computer has to be restarted for it to work again. I checked for all the updates and the wireless card and everything was fine.
View 1 Replies
View Related
Feb 27, 2011
Just bought two new LAP1041N APs to add to a dead spot on our campus. Well when trying to set them up the will not stay connected to the WLAN Controller (model 4402). The new APs boot fine, and will even appear in the controller for brief moments, but after a few seconds they dissapear and start showing the discovery status light pattern (green, red, amber). Just wondering if I am doing something wrong with these APs, or what the issue could possible be.We have 10 other APs that as soon as we connected to network were detected by controller and we configured from there. Most of those are 1010 or 1020s, we have a few 1131s and 1100s.
View 7 Replies
View Related
Apr 18, 2012
i noticed that the 1242AG does not bring up the Radios, when there is a Power Injector connected.I see in the Logs of the AP:
%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C6509 <Switchport MAC Add>
The Module in the 6500 is a WS-X6348-RJ-45 The Option "Power Injector installed" on the WLC is also enabled, with the MAC Address from the Switchport, but no change.When i disable CDP on the mentioned Switch Port and reload the AP, it comes up and runs fine.
View 7 Replies
View Related
Jun 26, 2012
Background: Wireless credit card machines can't stay connected to the 5508 controller 7.0.116 / 1142 ap wireless system. MAC address of one of the wireless hosts is 00:12:0e:ec:ce:97. AP servicing them is d4:a0:2a:99:34:60. Hosts are able to connect to the network after a reboot and stay connected for random periods of time but then don't come back unless you manually reload them. I have 3 in total in the same room services by the same ap.
I have the output of debug client 00:12:0e:ec:ce:97. Output showed 802.1x 'timeoutEvt' Timer expired for station 00:12:0e:ec:ce:97 so I increased the value to 4000ms on the controller but am still having the issue.
Note that the output below is the state the client stays in after receiving the timeout (802.1x 'timeoutEvt') showing subsequent attampts. The only way to get them back on is a reload of the credit card machine.
[Code]........
View 3 Replies
View Related
Apr 6, 2011
I have a Netgear Wireless Adapter WNA1100 and I'm trying to connect my 2nd desktop comp using it. I'm having trouble staying connected. The wireless connection says 100% but when I ope IE and yahoo homepage comes up it only stays connected for a sec and it says "unable to stay connect, do you wish to work offline" then it automatically put in offline mode, which doesnt work. Now it's saying IE cannot display webpage.
View 2 Replies
View Related
Jul 27, 2012
New E3200 router (a few weeks old).
Using the manual settings under Status/Router and clicking the Disconnect button (by Login Status), the page reloads, and say I am disconnected.
Without any input from me, about 30 seconds later the page reloads and say I am connected.
Clicking disconnect, closing the tab and testing my connection proves that I'm not actually being disconnected at all. I cannot force this router to manually disconnect.
Is this a firmware bug or is there another setting else where that prevents me from manually shutting down my connection?
Edit: Firmware 1.0.04 build 1 Apr 10, 2012
View 9 Replies
View Related
Dec 12, 2012
any luck getting Nest thermostats to stay connected on a cisco wireless network. We are running 5508s (ver 7.2.110.0) and the thermostats are connecting to a 3502. The WLAN is a locally switched FlexConnect SSID.
According to nest there are two potential issues - NAT timeout and wireless networks that do not play nicely with devices that sleep for long periods of time. I've configured static NAT translations for the Nests, so that shouldn't be an issue. Nest says "Nest uses Wi-Fi 'Power Save Mode' to allow it to sleep and charge its battery while remaining connected to the internet. Not all Wi-Fi routers support this feature or implement it correctly. When they don't, Nest will have difficulty sleeping and will restart in an attempt to reset its network connection. This may happen repeatedly if your Wi-Fi router is incompatible with the 'Power Save Mode' feature." I've tried increasing the DTIM timers to no avail.
View 3 Replies
View Related
Aug 1, 2011
I'm having trouble getting my laptop to stay connected to my wireless internet. This problem only occurs with my laptop (other laptops in the house are able to connect no problem) and with this particular wireless box (my laptop has no problems connecting and staying connected to other wireless networks, wi-fi, etc.).
I am able to connect to the wireless but it lasts only for a few minutes before connection is lost, so I basically have to connect to the internet through a ether cable (?) plugged into the wireless box.
I can't work out where the problem could be as the wireless works for other computers, and my computer works with other wireless networks!
I don't know if it matters but I am using a Toshiba satellite running on Windows 7.
View 9 Replies
View Related
May 11, 2013
I have a Dell Inspiron15z Ultrabook and a Cisco Linksys Wireless N Router, WRT120N. I recently took my computer offline for a week to go on vacation. Since Ive been back I keep getting kicked offline every so often
View 1 Replies
View Related
