D-Link DAP-1522 :: Loses Bridge Connection When Powered Down / Up?
Apr 17, 2011
It took a while but I've had my 1522 running well for several days. However, if I power down and then power up the 1522, it never reconnects. The bridge mode light flashes 5 times, then - nothing.
So, I have to disconnect everything, bring the 1522 back to my main PC, attach it, let it connect properly, then unattach and re-attach at it's use site.
(I'm using a static IP address and a Cisco E3000 router working perfectly with all my other stuff. Firmware v1.31)
I currently have a DAP1522 in Bridge mode with a DIR655. I am only using the 2.4GHz G mode on my 655. In a few days I will be replacing the 655 with an 825. When I log into the 1522 I don't see any settings for Mode, Frequency or Width (while in Bridge mode). The page for wireless setup is blank except for the "Save Settings" button. When I look at the 655, it appears that the 1522 is connected (bridged) at 2.4 GHz G like I would expect. So, when I install the 825 how do I make it connect at 5GHz N or will that be automatic if my SSID on the N mode of the 825 matches SSID on the 1522?
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled Bridge State : Connected MAC Address : fc:75:xxxxxx 802.11 Mode : Mixed 802.11a, 802.11g and 802.11n Band Width : 40 Channel : 6 Network Name (SSID) : cleveland Wi-Fi Protected Setup : Enabled Security : WPA2-PSK
I already have a DIR-855 and was considering using a DAP-1522 in conjunction to bridge my 5GHz N to my living room to feed HD media to my PVR box and also feed wired-only clients like my TV and BR player. But, in my new flat I find that the walls are pretty thick and my wifi signal is dropping off pretty quick, so I was wondering if you can configure the DAP-1522 to simultaneously be a wifi bridge to feed my media clients, and an AP to feed any laptops that might be in use in the living room?
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows: DIR-615: 192.168.0.1 DAP-1522: 192.168.0.50 (static) PC: 192.168.0.55 (static)
I've been playing with this setup for over a month with no real success. I'm trying to use the DAP-1522 as a wireless bridge to provide connectivity to my entertainment center which consist of a PS3, Directv DVR and Internet ready TV. I tried the setup as described in the manual, but not getting to the internet. Initially I was able to connect the 1522 as a bridge, but the connection kept dropping, especially anytime I actually used the internet (downloading a VOD movie). While troubleshooting the dropping issue, I changed all the 1522 settings and now it cannot access the internet at all through. The WNDR3700 is routing my home network fine...it is setup on the 192.168.1.x address space. I understand the 1522 came setup for 192.168.0.x, is the 192.168.1.x/192.168.0.x thing jacking things up? I initially had the 1522 setup with the 192.168.1.x IP from my home network and the gateway set to my WNDR3700 (192.168.1.1)...should it be on the 192.168.0.x? I have updated the firmware to 1.31.
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
If you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
I have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
I purchased a wireless bridge D-Link DAP-1522 (IP fix 192.168.0.50) to share the Internet connection to two remote devices: WD TV Live HD (IP fix 192.168.0.52) and a Samsung BD P2500 player (IP fix 192.168.0.51: to try the BD-Live) but when I plug it into my network I have an IP conflict and I can not navigate anywhere, even by the computer which control the Netgear router (IP 192.168.0.1 DHCP range 192.168.0.2-192.168.0.49).
I tried with all fixed IP (192.168.0.xxx Subnet mask 255.255.255.0 Gateway 192.168.0.1 DNS 192.168.0.1), but nothing to do, I have the same problem: after a few minutes after plugged the network cable into BD player the network falls.With wired connection (10 m of patch cable!!!) Samsung BD P2500 have no problem (DHCP and IP fix).
Then look closely in the information relating to devices connected to the Netgear router I noticed that all devices connected through the bridge DAP-1522 have the different IP but same MAC address and I think this could be the cause of the problem that creates the Blu Ray when it's connected to the network through the bridge, because he is not identified with any name but only as UNKNOWN as the bridge (a problem that WD Live not seen: same MAC address but is identified by name as WDTVLIVE).
How can I make the MAC addresses from the bridge will be recognized separately from my router/modem Netgear?In the settings of the bridge I noticed that you can enable or disable MAC address cloning, but if the off I would expect that cloning was not done and instead all the devices are identified by the Netgear router with the MAC address of the access bridge.The DAP-1522 masked the MAC address of device that are plugged into bridge.The router has the latest available firm while the original bridge has version 1.20 (the penultimate version available).
I Recently purchased the DAP1522 to use as an entertainment bridge for my xbox 360, BR player and dish network receiver I also upgraded my router a WRT5GS running tomato to a Linksys E4200 going from G to N while i had my Xbox and BR connected wireless I didn't have the Dish receiver hooked up so i thought by using the DAP i would be upgrading my network and connecting my Dish receiver no brainier right and everything works so far.But here's the question with all the hype of the benefits of the 5ghz channel , well it's not hype it certainly makes sense but from what I see the products have to be compatible shouldn't what I'm connecting be compatible they say your gaming console specifically and streaming movies i would think . Any configuration tips I read somewhere that with an E3200 router they had to set the 5ghz channel to like 37 for the DAP to see that channel its all getting a little overwhelming here's whats in the house A Mac Power PC pre Intel using a Asus NB13 USB 2.4ghz its the only thing i could find with speeds over 100Mbps A windows 7 machine hardwired gig connection another windows 7 pc downstairs hardwired a netbook with a wireless connection and lastly a DECT 6.0 phone system who knows what interference these produce.
We currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
Region : Others Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version : ISP :
I have 2 TP-Link # 941NDs at my home. ( version 3.6 )In the new ( second ) TP link, i activate WDS - Wireless Bridge. And configure it to through Wi-Fi connect with earlier TP-Link, and also to act as router to cater to PCs within its range. IPs are set as per of same family as that of primary TP-Link, and further, DHCP been de-activated as well. Have sent WEP security as well.It performs correctly for the time, its stays ON, but when its switched Off, and then On again, it is not able to connect to the primary TP-Link and thus not able to serve its client PCs.
I use a WUMC710 bridge with desktop PC and a Printer connected to it. When those two devices have been inactive for a while the bridge goes into sleep mode and loses the connection Back to my EA6500. Trying to print something from wireless devices connected to the 6500 elsewhere in the network doesn't "wake up" the bridge. Ihave to unplug the power supply and restart it.
I have a fibre optic internet connection, the modem being connected to the TP Link wireless router. The set up works fine most of the time, but at times all the computers connected lose internet connection. The ISP says everything is fine from their end, and locally we are all connected to the wireless router just fine when this happens. I usually just unplug the modem and the wireless router from their power, in order to reset everything, and this seems to solve it.
I have a dir-825 connected to Cable modem and a dap-1360 connected I have both wireless and wired clients.If get a ip address conflict and the the dir-825 connection fails from the cable modem and nothing seams to restore that connection, i reboot both route and modem and make sure no client are on. The only way i can figure out how to restore the router is to reset and reinstall from factory state.I can recreate this on 2 different router "825" with factory and updated firmware.I have removed the wireless extender form the picture and this issue has stopped, it might be the extender of a client off the extender. But everything uses DHCP so I'm not sure why ip address conflicts could cause this issue.
I have just upgraded my network to the 802.11n standard, or at least am trying to do that. Im using a DIR-615 as Access Point and a DAP-1522 as bridge to cover the entire area.After having some trouble figuring out how to set up and connect the devices, i figure out that it might some other problem than my setup of the devices (The symptom was that the connection was ok, but then it seemed to be dropped, even though the DAP-1522 still displayed connected in the status page).
After reading what I could find about the DIR-615 and DAP-1522 in this forum and on the internet, I found a suggestion about changing the Wireless Mode from 802.11b/g/n to 802.11b/g, and after doing that everything works fine, its just not an upgrade anymore.I have fixed the channel to 10, just to check that it wasnt noise from other equipment. The symptoms are very reproducable, trying to connect wiin n-mode and bridge only works for 30-60 secs. Switching back to b/G mode and all is fine.
I have a DIR-655 set up as follows: [code] Lost Internet Access on my DAP-1522 on only my wireless laptop connection, but not other wireless nodes on the DAP-1522.I have most of my wireless nodes attached to the DIR-655, which is upstairs. Downstairs is where the DAP-1522 is located. There is a wired connection between the DIR-655 and DAP-1522. The DAP-1522 is being used as a Access Point. On this I have only three nodes that are wireless. My Smartphone, iPad and my laptop. There are also three nodes that are using the wired ports with no issue accessing the internet. The setup above have being working for over two years with no issue. Then three days ago my laptop connects to the DAP-1522, but has "No Internet Access." If I change my wireless connection to the DIR-655 on my laptop, then I do have internet connection. My Smartphone and iPad still are able to access the DAP-1522 and get the internet.
I have deleted my DHCP Reservation for only my laptop on the DIR-655. Wireless connection to the DAP-1522, looked at the DIR-655 and see that DHCP Reservation show the MAC of the laptop and I Reserve it. Still "No Internet Access." On the DAP-1522 it does show that my laptop is associated to this device. I cannot ping my local LAN IP Addresses , a website or Public IP Address only from the laptop. The DIR-655 shows a "Do Not Enter: Wireless system with MAC address 4025C2B97110 disconnected for reason: Received Deauthentication" with a connection to the DAP-1522, but shows "Do Not Enter: Wireless system with MAC address 4025C2B97110 secured and linked" with a connection to the DIR-655.
I have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
My D-Link DIR-300 very often loses connection on wired and wireless connections. It stops connecting to Internet randomly i.e. any URL typed in from the browser times out.I connect various devices such as desktop, laptop, ipad2 over wired and wireless connections and the behavior is the same from all devices when this problem occurs. If I make a direct connection to the DLS modem, it works fine for the whole day, without these issues.I also observed IP address conflict messages and my desktop does not connect to Internet if I am running VPN on my laptop, at the same time, occasionally.When this occurs, I am able to login to the router and can see the WAN status and the DHCP address being allocated to the router. I can even do DHCP release and renew, but that does not fix the problem.
Region : Canada Model : TL-WR700N Hardware Version : V1 Firmware Version : latest ISP : Cogeco
I have a WR700N set up in bridge mode so as to provide a wifi signal in far end of our home. I used Bridge so we can tell which router we are connecting to. So we have two SSIDs (MySSID1 and MySSID2) Both with secure log-in. This works fine for about a day, and then disconnects. I then have to mess with the WR700N by plugging it in and out, maybe logging into it and changing something. Then it will work again - for a day
I updated the firmware with no change. Main router is a Dlink 615 with IP of 192.168.0.1. connected to cable modem. TP-LINK is set at default of 192.168.0.254 and gets a wireless signal from dlink.In an attempt to improve situation, I now have both units set to channel 11 and with fixed 20Mhz channel width. b/g/n on TP and g/n on dlink.
I'm trying to hook up a dap-1522 to an SMC8014WG wireless router. All goes well for about 10 minutes then the SMC drops all wireless connections except the connection to the 1522, and loses internet connectivity.There are several other wireless devices connected to the SMC but none of them causes it to go down.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n ISP : Comcast
The 5 ghz connects fine for multiple machines however machines on 2.4 simultaneously lose their connection to the internet, sometimes saying it is still connected to the internet when it is not and sometimes losing connection with the router entirely. The 5ghz still works when this happens.
I have an old laptop in another room running WMC with windows 7. This is wired to my new DIR 655 router then via a switch to another room to my xbox 360. I have successfully connected the xbox as an extender but after a few minutes of idle time, the connection drops and my xbox automatically restarts. If I'm streaming something it seems to work fine.
I have my dap-1522 connected to my dir-655 in bridge mode. I was having intermitant connection problems with the dap-1522, so I updated the firmware to 1.41 for version A1. Now when I go to change the connection type to dynamic ip and save, it reverts back to static ip, which makes this thing useless for my network. Why won't it save?
Region : UnitedStates Model : TL-WR940N Hardware Version : V1 Firmware Version : TL-WR940N_v1_120201 ISP :
Just bought a TL-WR940N and it was always loosing connection and freezing / locking up. I upgraded to the latest FW from the link below URL but it still freezes and loses connection to devices after 8-12 hours, keeps hanging up and pages sometime don't load.
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
I have a DIR-615 router (h/w ver E4 and firmware 5.10) that needs to be powered off and then on again several times in a day (a reset of sorts).After being on for sometime, most devices lose connectivity to the router and new devices cannot connect to it.After being powered off and then on again, everything works fine.
