TP Link Td W8951nd - Connecting To Router / Configuring Settings?
Feb 3, 2013
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
Region : India Model : TD-W8951ND Hardware Version : V4 ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
i have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
just bought DCS-930L few days ago, the manual sounds so easy (but it's hard than it looks) i stuck on the setting-up, here is my problem: unable to connect to mydlink web site and there was a problem saving my settings. seems like internet connecting problem, the software just couldn't connect to internet.i have already registered, i got my device number and it couldn't be find in my device on mydlink.
I have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
Region : India Model : TD-W8951ND Hardware Version : V4 Firmware Version : ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : India Model : TD-W8951ND Hardware Version : V1 Firmware Version : 5.0.0 ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Region : Kazakstan Model : TD-W8951ND Hardware Version : V4 Firmware Version : 4.0.0 Build 120207 Rel.10587 ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V5 Firmware Version : 5.0.0 Build 120703 Rel.29030 ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V1 Firmware Version : Latest ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
Region : Malaysia Model : TD-W8951ND Hardware Version : V5 Firmware Version : V5 ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
Region : Poland Model : TD-W8951ND Hardware Version : V5 Firmware Version : 5.0.0 Build 120522 Rel.23978 ISP : Orange/TPSA
My router TD-W8951ND remembers only a dozen of latest logs. Previous, older logs disappears. Why? Is there any way to force router to keep logs from, for example, the last 12 or 24 hours?It is important to me because i have some problems on my adsl line and i want to know what happens with connection while I am not in home or when I sleep.If it will be necessary I am able to log onto my router using Telnet, just give me required commands to fix this problem with logs.
-Region : Poland -Model : TD-W8951ND -Hardware Version : V5 -Firmware Version : 5.0.0 Build 120522 Rel.23978 -ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V5 Firmware Version : TD-W8951ND_v5_120522 ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V5 Firmware Version : 22.05.2012 ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
I have a Sky [Sagem] F@ST2504N Wireless Router and Sky is my ISP. I have been using powerline adapters to extend my network into a room upstairs that is a WIFI deadzone. I would like to use a router to turn this into a wireless signal in the upstairs room. i.e. Primary (SKY) Router -> power line in -> powerline out (Upstairs in deadzone) -> Secondary (TP-Link) Router..I have got a TP-Link 150mbps wireless N ADSL2+ Modem Router (Model No.: TD-W8951ND) .I am plugging this in and configuring it from factory settings via the web setup. How to configure the new router?
why I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page.
Region : Argentina Model : TL-MR3220 Hardware Version : V2 Firmware Version : ISP :
Region : India Model : TL-MR3040 Hardware Version : V2 Firmware Version : 3.14.2 Build 120822 Rel.40902n ISP : Reliance
Configuring my TL_Mr3040 with Huwei EC 150 model USB modem, the modem and ISP name is there in the list , I have configured all (manual/ as well as auto ) methods of authentication as mentioned in user guide.
for more infor , the exported profile from laptop where my modem works fine is <?xml version="1.0" encoding="utf-8"?> <utpsdoc type="Profile"> <ProfileGroup type="DialUp"> <Profile name="Reliance" type="" readonly="" device="" user="74831*****" password="74831*****" phonenumber="#777" autoapn="true" apn="" chap="true" pap="false" ip="" dns="" dnsalt="" wins="" winsalt="" imsi="" langid=""/> </ProfileGroup> </utpsdoc>
Region : Argentina Model : TL-MR3220 Hardware Version : V2 Firmware Version : Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
I have the DIR-655 (H/w Ver B1, F/W Ver 2.05NA) set up as router on my network (TWC/RR - modem is Motorola SURFBoard 6121 - modem only, no router or other services provided). I have configured the router sufficiently to allow all computers on the local network to access the Internet, and have configured the DHCP server on the router to provide IP addresses to the local network. I have configured the router to provide the DNS addresses for my local DNS resolvers (so that I can provide DNS resolution for an "internal" domain). Configuration specifics available on request, but everything mentioned so far is working satisfactorily, at least so far.
So, my question: The "Local Domain Name" setting on the router, as indicated in the documentation, provides a connection-specific domain name when DHCP supplies an IP address to the local system. This setting, however, is overridden if the ISP provides a domain name when it assigns an IP to the WAN connection. I have verified by experiment that this is true (no matter what I put in the Local Domain Name field - whether a valid domain, or blank - the local machines receive the domain name supplied by the ISP.I wish to modify this behavior. I wish to have the router provide the domain name specified in the Local Domain Name field *regardless* of what the ISP provides.
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
I have been trying for days to get a HP Photosmart Plus B209a wireless printer to work with my D-Link DIR-655.Going through the HP setup cd for I get to the section where it wants to hookup a usb cable to get router settings and finds my network and then I put in the password. Then after looking for a bit it says it can't find the printer.Looking at the wireless status page it says the ip address is 0.0.0.0.Reading on HP's website it says that you must have the router set to broadcast the SSID, I believe mine is set to hide. How would I go about changing it to broadcast AND would it mess up all my other settings changing it to Broadcast, meaning will I have to reconfigure the other computers again? Do I use the set up wizard to edit things or is that for first time set up ?
None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
I have the following network setup. I have a dynamic IP address from my ISP. I connect my fiber to a D-Link DIR-645 and set up my wireless network. The coverage is kind of poor in my son's room so I use a D-Link Powerline Homeplug 501AV to extend internet to my son's room. I connect one Homeplug to the DIR-645 and set the other Homeplug in the power outlet in my son's room. It works if I connect his PC or Xbox via an ethernet cable to the Homeplug in his room. Since he has both PC and XBox I have connected a D-LINK DIR-100 to the Homeplug and have two ethernet cables connecting to his PC and Xbox. Here is the problem. I don't get an internet connection to the DIR-100.How shall I configure the two routers to work?
