TD-W8951ND How To Configure New Router
Dec 7, 2012
I have a Sky [Sagem] F@ST2504N Wireless Router and Sky is my ISP. I have been using powerline adapters to extend my network into a room upstairs that is a WIFI deadzone. I would like to use a router to turn this into a wireless signal in the upstairs room. i.e. Primary (SKY) Router -> power line in -> powerline out (Upstairs in deadzone) -> Secondary (TP-Link) Router..I have got a TP-Link 150mbps wireless N ADSL2+ Modem Router (Model No.: TD-W8951ND) .I am plugging this in and configuring it from factory settings via the web setup. How to configure the new router?
View 4 Replies
ADVERTISEMENT
Mar 18, 2013
i have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
View 1 Replies
View Related
Feb 3, 2013
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
View 5 Replies
View Related
Mar 28, 2013
I have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
View 1 Replies
View Related
Mar 31, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
View 4 Replies
View Related
Jan 1, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
View 1 Replies
View Related
Dec 9, 2012
Region : Kazakstan
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120207 Rel.10587
ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
View 2 Replies
View Related
Nov 8, 2012
Model : TD-W8951ND
Hardware Version : V3
Firmware Version :
ISP : BSNL DATAONE
my tablet show wifi status connected ... signal quality... but cant access internet ...
View 2 Replies
View Related
Feb 24, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
View 1 Replies
View Related
Dec 6, 2012
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : Latest
ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
View 2 Replies
View Related
Feb 20, 2013
Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
View 1 Replies
View Related
Apr 29, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
View 2 Replies
View Related
Feb 16, 2013
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
My router TD-W8951ND remembers only a dozen of latest logs. Previous, older logs disappears. Why? Is there any way to force router to keep logs from, for example, the last 12 or 24 hours?It is important to me because i have some problems on my adsl line and i want to know what happens with connection while I am not in home or when I sleep.If it will be necessary I am able to log onto my router using Telnet, just give me required commands to fix this problem with logs.
View 3 Replies
View Related
May 7, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version :
4 lan ports problem in my modem. Able to get internet through wifi but unable through lan ports.checked in 2 pcs and 1 laptop
View 1 Replies
View Related
Dec 23, 2012
Region : India
Model : TD-W8951ND
Hardware Version : V4
ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
View 6 Replies
View Related
Feb 17, 2013
-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
View 2 Replies
View Related
Feb 16, 2013
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
On my router TD-W8951ND constantly there are the same type errors, while using computer conected to the router:
Code:
2/16/2013 17:24:8> netMakeChannDial: err=-3000 rn_p=80544b08
2/16/2013 17:24:13> Last errorlog repeat 2 Times
[Code].....
View 1 Replies
View Related
Apr 8, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
View 1 Replies
View Related
May 3, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 22.05.2012
ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
View 1 Replies
View Related
Dec 28, 2012
Is it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies
View Related
Feb 29, 2012
How to configure a router so that i can ping it while there is another router in between
View 1 Replies
View Related
Mar 1, 2012
I have bought D-615 wireless router, I have Cable modem, am trying to configure however unable to do it?
View 1 Replies
View Related
Jul 21, 2011
How to configure dwl-2100ap router
View 1 Replies
View Related
Sep 1, 2011
got the DIR-655 for gaming not knowing about LAN and WAN can any tell me if i can config this router to work properly with my broadband i have ONT that the router connects to
View 1 Replies
View Related
Mar 30, 2011
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies
View Related
Nov 3, 2012
Here is my Desktop Specs:
Windows XP Svc Pack 3
Mainboard :Asus P5KPL-CM
Network Card :Atheros AR8121/AR8113 PCI-E Ethernet Controller
Current Router - LinkSys BEFSR41 (Hardwired, CATV cable)
Static IP - 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1
Problem: I purchased a new GB router, Dlink DIR825, wireless and 4 ports, and cannot connect to it to set it up. I need to get into it to change its IP address from 192.168.0.1 to 192.168.1.1 and to make a few other changes. I have 6 different ethernet cables, all of which work with my desktop as well as my laptop. I can get into the new Dlink router just fine with my laptop so it is not a bad port on the new Dlink. The cables work with my existing router and my new router using my laptop so it isn't a cable problem.My internet connection is Hughesnet (DISH) which uses the 192.168.0.1 address, the same as the new router. So here is what I have tried:
1. Powered down Hughes router, new router, and old router.
2. Removed cable from Hughes router to old Linksys.
3. Changed static IP on desktop from 192.168.1.100 to 192.168.0.50 and Gateway to 192.168.0.1.
4. Rebooted
5. Connected ethernet cable from desktop to Port 1 on new router.
6. Powered up new router.
7. Brought up Browser and entered the 192.168.0.1. Nothing happens. The Port light on the new switch shows the connection properly and the other lights are on properly, except for the Internet light which I haven't hooked up yet.
The above does not work so I powered down everything and then:
1. Connected the cable from the Hughes internet modem to the Internet port on the new modem.
2. Powered up Hughes modem and waited for all lights to come on.
3. Then powered up new router and waited for all lights to come on. This time the Internet light came on like it should.
4. Powered up my desktop.
5. Brought up Browser and entered the 192.168.0.1. Nothing happens. I expected this since there would be a conflict with the 2 modems having same IP.
Next I tried to basically set my desktop to use DHCP and removed the cable from the Hughes modem to the new router. Powered down everything then brought them up one at a time, Hughes modem, router, and PC. Still not able to connect to the new router.I also used my laptop to set the new router to 192.168.1.1 and reset my static IP to the original 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1. Still nothing and I couldn't even ping the router.
View 7 Replies
View Related
Sep 16, 2011
Right now I have it connected like this: Internet-> SURFboard SB6120 Modem -> DGL-4100 Router (modem in the WAN port, 3 internet connections plus the switch in the LAN ports) -> DGS-1008G Switch (2 other internet connections connected to this, as well as an Xbox 360).The problem is that everything connecting to the router works, and nothing works on the switch even though the power light is on (however, the port on the router that is receiving the switch is not lit up). I'm guessing this is because the router only assigns as many IP addresses as it has ports or something.
View 10 Replies
View Related
Feb 22, 2013
I am researching routers for a large emnterprise application, and their useability as firewalls. Also, is their one that is considered to be better over another?
View 3 Replies
View Related
Aug 5, 2012
I'm active duty military, currently overseas.I have a wireless connection and recently purchased a Samsung HT-E5500 home theater system. I'd like to be able to stream Netflix but understand that I need a VPN with a US ip address to get it to work. Any VPN service I can use, and how to configure it with a Linksys E3000 router, so that I can use it with both my computer and when connected to the Samsung system?
View 1 Replies
View Related
Jan 23, 2011
My boss want me to configure a cisco router 1800 series to an IP VPN, but I don't know how to configure a router with an IP VPN...
View 2 Replies
View Related
Dec 20, 2011
Can't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
p.s. the router is a Netgear model # WGR614
View 4 Replies
View Related
Feb 14, 2011
How to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
View 1 Replies
View Related
Dec 1, 2012
I have a Netgear WNR1000v3 router that I just reset to factory defaults, and now when I run ipconfig /all it doesn't show up as having a gateway. Note that I am connecting with a laptop wired in to a LAN port on the router. (also tried on WAN port) Here is what shows up:
SpoilerEthernet adapter Local Area Connection:
View 1 Replies
View Related
