Can't Get To Admin Screen To Configure New Router
Nov 3, 2012
Here is my Desktop Specs:
Windows XP Svc Pack 3
Mainboard :Asus P5KPL-CM
Network Card :Atheros AR8121/AR8113 PCI-E Ethernet Controller
Current Router - LinkSys BEFSR41 (Hardwired, CATV cable)
Static IP - 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1
Problem: I purchased a new GB router, Dlink DIR825, wireless and 4 ports, and cannot connect to it to set it up. I need to get into it to change its IP address from 192.168.0.1 to 192.168.1.1 and to make a few other changes. I have 6 different ethernet cables, all of which work with my desktop as well as my laptop. I can get into the new Dlink router just fine with my laptop so it is not a bad port on the new Dlink. The cables work with my existing router and my new router using my laptop so it isn't a cable problem.My internet connection is Hughesnet (DISH) which uses the 192.168.0.1 address, the same as the new router. So here is what I have tried:
1. Powered down Hughes router, new router, and old router.
2. Removed cable from Hughes router to old Linksys.
3. Changed static IP on desktop from 192.168.1.100 to 192.168.0.50 and Gateway to 192.168.0.1.
4. Rebooted
5. Connected ethernet cable from desktop to Port 1 on new router.
6. Powered up new router.
7. Brought up Browser and entered the 192.168.0.1. Nothing happens. The Port light on the new switch shows the connection properly and the other lights are on properly, except for the Internet light which I haven't hooked up yet.
The above does not work so I powered down everything and then:
1. Connected the cable from the Hughes internet modem to the Internet port on the new modem.
2. Powered up Hughes modem and waited for all lights to come on.
3. Then powered up new router and waited for all lights to come on. This time the Internet light came on like it should.
4. Powered up my desktop.
5. Brought up Browser and entered the 192.168.0.1. Nothing happens. I expected this since there would be a conflict with the 2 modems having same IP.
Next I tried to basically set my desktop to use DHCP and removed the cable from the Hughes modem to the new router. Powered down everything then brought them up one at a time, Hughes modem, router, and PC. Still not able to connect to the new router.I also used my laptop to set the new router to 192.168.1.1 and reset my static IP to the original 192.168.1.100, 255.255.255.0, Gateway 192.168.1.1. Still nothing and I couldn't even ping the router.
View 7 Replies
ADVERTISEMENT
Oct 29, 2011
I have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
View 8 Replies
View Related
Nov 30, 2011
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
View 3 Replies
View Related
Jan 23, 2012
How to configure a LobbyAdmin account for WLC 7.0 on a 5.1 ACS? I'm very new to ACS 5. How to configure it.
I've got the ACS policy working that allows me to login to the WLC using a user account with full rights but the Lobby admin account can login with full rights as well. I've tried setting the custome attributes in the shell profiles with role0-mandatory-LobbyAmbassador, task0-Mandatory-Configure Guest User and task1-Mandatory-Lobby Ambassador User Preferences but it still doesn't work.
View 18 Replies
View Related
Aug 5, 2012
how to configure ACS 5.2 for device administration of Checkpoint firewalls and security management servers?
View 4 Replies
View Related
Feb 28, 2012
Why should I need a router with a touch screen? Just because, its fancy or just because its bringing a new trend to wireless networking? I wanted to buy the D-link DIR 865 but it became vaporware. Now this came up Almond of Securifi. Dong Ngo of CNet has reviewed it. Does it really make sense to buy a wireless touch screen router, leaving the old trend of traditional routers with web interface?
View 2 Replies
View Related
Jul 29, 2012
I am trying to change the name of my wireless network but when I go to the 192.168.1.1 and type in my password, it just goes to a blank screen. I've accessed my router a lot of times before this way. It is a lisksys router.
View 1 Replies
View Related
Feb 13, 2011
I followed the instruction and type cmd, then in the black screen, i typed ipconfig. lots of data appeared, i copied the ip address to the browser, but it can't open the page.
View 2 Replies
View Related
Dec 8, 2012
Cannot connect to Linksys Router 192.168.1.1 Webpage, do not get login setup screen.
View 1 Replies
View Related
Mar 23, 2013
I've just discovered that my wireless router is not secure (WRT54GS v5). In trying to set up the propoer security, the set up screen appears as incomplete (after entering 192.168.1.1). It only shows 3 tabs at the top - Basic Setup, MAC Address Clone, and Advanced Routing. No tab to deal with the settings. I have tried resetting the router and plug/unplug several times. Triued entering thru IE and Firefox.Is there another way to set up the security on my router or at least get the proper screen?
View 4 Replies
View Related
Sep 11, 2012
I have a computer that is connected to a linksys wireless router model WRT160NV2. I also have a laptop. I have never set up a lock or anything on my wireless connection and I think other people are using it. When I type the IP address 192.168.1.1 on my laptop, I do not get the screen to pop up to change my settings. Do I need to do this from the computer?
View 1 Replies
View Related
Jan 7, 2011
how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies
View Related
Sep 7, 2012
I have the EA4500 router with cisco connect cloud, must say this router is great for limiting kids online.1 question I have however is the ability for a blocked user (internet access block) that is redirected to the cisco web site and presented with a log in screen. Is there anyway I can disable this becuase the kids stay up all night trying to figure out the password to log in, I just want it to say internet access blocked with no option for logging in for the blocked user.
View 7 Replies
View Related
Nov 2, 2012
EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
View 9 Replies
View Related
Apr 27, 2007
When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
View 3 Replies
View Related
Jan 7, 2012
After popping in the installation CD, the screen says hook everything up, which I do. Then click next, where it says "Searching Networks", then quickly changes to "Connecting to Network", and then it says it "Cannot Find Router.". Err. Check setup, etc.If I hook up directly to new router VIA internet cable. Also, this is strange: When I just open up a web browser and try to log into the router 192.168.1.1, using no user name, administration as the password, it won't let me in to the router. Even after I have reset the router with a pen.
View 1 Replies
View Related
Jan 9, 2012
I have a wrt54G v8 wireless router and I was trying to install a firmware update a while ago and got impatient, stopped the upgrade in the middle of it and I think I may have bricked my router. I've since tried the 30/30/30 reset a number of times and have noticed that I don't get a blinking power light which I guess means it's ok.
Now when I go to 192.168.1.1 and log in, I can see most menus but when I click the firmware update menu (there's another screen that's also all white, I forget which one), it's all white (or blank). I've searched for a solution on the web and no luck so far.
I've been trying to do this on a mac and no luck. I then booted into windows 7 and used IE 9 to log into 192.168.1.1 and still the same thing, the firmware update screen is blank.
View 1 Replies
View Related
Apr 8, 2012
I installed this Linksys E1500 yesterday and have had a problem keeping my iPhone 4 and an iPod Touch connected to WiFi.The devices go to sleep. When I swipe the screen and "bring them back" the WiFi is Not Connected. I have to go in and re-enter my network password again. As long as the devices don't go to sleep, they maintain connectivity. Once connected they function properly.
The iPad 2 & Samsung Galaxy S phone we have seem to be keeping their WiFi connectivity, as well as a G62 HP laptop running Windows 7, an older XP machine using a Cisco AE1000 wireless network adaptor and the Xbox 360. The issue is just with the iPhone 4(ios 5) and the iPod Touch(ios 4).
I had issues with the iPad and the Galaxy phone until i disabled WMM Support in App & Gaming.I would bring this back to the retailer but I had it sitting on my desk for about 30 days and it's past their return policy.The firmware is up to date on the Router. I've tried power cycling all the devices including the cable modem & the new router.
View 1 Replies
View Related
Jun 26, 2012
I tried to log in into my EA4500 today, and instead of the simple window that asks for the user name and password, I am getting a Cisco Connect Cloud log in screen. It is very strange.
At the top it says: Cisco Connect Cloud/Powering Linksys Products
and below that:
Sign In If you have not yet created an account, click the 'Create Account' button in the upper right corner of the page
There is a help button, a button to create an account. There is a place where I can enter an email address and a password.
Pressing the Help button I learned that I can probably bypass this silly screen by disconnecting the internet. Is there a better way to bypass this screen and turn off Cisco Connect Cloud?
View 9 Replies
View Related
Nov 11, 2012
is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.
View 4 Replies
View Related
Jan 18, 2012
I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was stoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to thenavigator for show the administrator´s window. Any procedure to recover the operation of the router in a situation like this?
View 1 Replies
View Related
Dec 13, 2012
Unable to access router admin page for Haier model R800
View 1 Replies
View Related
Apr 1, 2012
I want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies
View Related
Jul 3, 2012
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies
View Related
Jul 20, 2012
I have lost my router wordpass admin.
View 1 Replies
View Related
Jan 29, 2012
I have a binatone wi-fi modem. Internet is working good from router but i am not able to connect to router admin page i.e 192.168.1.1 and not be able to change wi-fi password.
View 3 Replies
View Related
Jul 25, 2012
I am attempting to configure Radius for use with a Cisco router for the first time. I have read a few tutorials online for setting up administrative access to the router using active directory accounts. On the surface this doesnt seem to over complicated. My question is: Is it possible to have one Cisco IOS router set up with radius authentication for administrative access AND have the same router set up for VPN clients who will be authenticated via the same Radius server? The router I am using is a Cisco ISR 2911 and the IOS version is "Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2".
View 1 Replies
View Related
May 7, 2012
I have a cradelpoint mbr800 wireless router and an axesstel mv240 usb modem. The modem works fine when plugged straight into my computer, but if I plug it straight in to my router the lights light up like it is aquiring and then go dark. And this cycle just keeps repeating. Now when I plug the usb modem in to my computer I have to push to connect on the start up manager before I can get on the internet. Is this why It will not work plugged straigh in to the router? and if so is there anything I can do to get it to connect through the router? I also can not get to the router admin to look at or change the settings.
View 5 Replies
View Related
Feb 4, 2012
We have a fast broadband service and three teenagers, two of which have laptopsWe are allowed 100Gb/month; if we exceed that, the we are charged $1.5/Mb. The provider has a web interface where we can check the last 24hours' usage. When ever we go over the daily budget, I ask the darling children who was watching all the videos-- to which they all say "not me".I want a wireless router with some admin features that allow me to see real-time who is the bandwith pig and shut them doI am not aware of any routers in the $100-$150 range that have these kind of features. There are industrial grade Cisco routers, but these have more features than I need and are really expensive
View 2 Replies
View Related
Oct 18, 2012
I just got back from being gone for a couple weeks and my router stopped working. I tried to reset the router and connect to the admin screen at 192.168.1.1, but it gives a "page not found" error. My internet work with a wired connection to the router, and the computer's IP address is 66.xxx.xxx.xxx. Looking at most forums which talk about this problem it seems like most people have IP addresses starting with 192. Why does mine start with 66? Is this related to the problem of being unable to access the admin screen? This is a home network and I'm running Ubuntu and have a Linksys WRT54G router. I get the same IP address whether I connect just from the modem to the PC, or from modem to router to PC.
View 3 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
May 22, 2012
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies
View Related
