Linksys Wireless Router :: E1500 When Swipe Screen And Bring Them Back / Wifi Is Not Connected
Apr 8, 2012
I installed this Linksys E1500 yesterday and have had a problem keeping my iPhone 4 and an iPod Touch connected to WiFi.The devices go to sleep. When I swipe the screen and "bring them back" the WiFi is Not Connected. I have to go in and re-enter my network password again. As long as the devices don't go to sleep, they maintain connectivity. Once connected they function properly.
The iPad 2 & Samsung Galaxy S phone we have seem to be keeping their WiFi connectivity, as well as a G62 HP laptop running Windows 7, an older XP machine using a Cisco AE1000 wireless network adaptor and the Xbox 360. The issue is just with the iPhone 4(ios 5) and the iPod Touch(ios 4).
I had issues with the iPad and the Galaxy phone until i disabled WMM Support in App & Gaming.I would bring this back to the retailer but I had it sitting on my desk for about 30 days and it's past their return policy.The firmware is up to date on the Router. I've tried power cycling all the devices including the cable modem & the new router.
View 1 Replies
ADVERTISEMENT
Sep 17, 2012
I have tried everything and every connection suggested and still can not get a wireless conection.
View 2 Replies
View Related
Jun 17, 2012
I am trying to find out what devices are connected to my router. I have had some illegal downloading from my IP address but it has not been done from my computer. It is showing in Cisco Connect that I have 15 devices connected, I should have no more than 6 devices connected so trying to figure out who is connected on my computer.
View 9 Replies
View Related
Oct 19, 2012
I have a linksys 1500, connected to a cablemodem. It has firmware 1.0.04 (but this problem happened with earlier firmware that it shipped with).I have a problem with the DHCP server on the E1500 - or maybe its a bad client - one of my clients, happens to be an iPad-2 doesn't seem to get properly connected. all of my other wireless DHCP clients - windows vista, windows 7, linux, android, mac and an old iPad1 all connect without problems. I also have wired devices that get their IP via DHCP for my TV, blu-ray, slingbox, DVR, without problems, its just this iPad2 that tries to connect, seems that it does, but can't access anything on the internet.I see this on the DCHP Client list (Status -> Local Network -> DHCP Client Table from the web interface) and I'm quite sure this is the cause of the problem with the iPad2. that MAC address is the address of my iPad2, and that IP# is the one I reserved for it.
I've set up that MAC address to have a reserved IP#, and forced the client name to Rays-IPad2 (as its named on the device) but it has the same behaviour as letting the DCHP server give it an IP# from its address pool. And if I reboot the E1500 and reboot the iPad2, it does actually connect for a few seconds, I can bring up a page in safari, etc, but soon within a few seconds, it switches the client name to this display of question-marks (non printable characters presumably) and it can no longer get to the internet.Is there anything I can do or try? There isn't another DCHP server running on the network, I don't know if something with the cable modem is causing a conflict, and if it were I'm not sure what I could do about that.
View 3 Replies
View Related
Dec 10, 2012
I have 3 laptops connecting wirelessly to this router. One is running at 18Mbps, the other two at 0.4Mbps. the internet setting are the same and the security is the same (WPA2-Personal with AES encryption). One of the slow computers is brand new and WAY faster than my "fast internet" computer. The other is about the same as the "fast internet" computer. I updated the I connected the new computer to the router tusing an ethernet cable and it had superfast internet. I redid the Cisco connect on each computer, but it didnt change anything. Why is it so slow wirelessly?
View 4 Replies
View Related
Jan 31, 2013
I am having a problem with an adapter, but I don't know if it's a router issue, adapter issue or software issue.
Router: E1500
Adapter: WUSB100
OS: Win XP Pro SP3
System: Dell Inspiron 9400
When the laptop has gone into standby and comes back out it is not connected to the internet or the 'secured side' of teh router. Instead, it asks for the 'guest side' password. When I try running Wireless Manager it goes through the entire process of 're-mating' adapter and router. That can't be right.How do I fix this so the system comes out of standby in the 'secured side' of the router?
View 9 Replies
View Related
Oct 26, 2011
My E1500 worked perfectly before. Today CiscoConnect notified me to upgrade my router. After I've done that, the wifi connection speed is super slow. But when I use hardwire to connect, the speed is as fast as before
View 9 Replies
View Related
Feb 9, 2011
I installed google toolbar for taskbar but I want yahoo for my homepage
View 1 Replies
View Related
Apr 11, 2011
I need WIFI inside a giant steel Quanset hut. There is a good signal right outside. Is there a way to do this with one device? I was wondering if I could put one of the antennas of a WRT54G through a hole to the outside and then set it in repeater mode. Theory being it would use the outside antenna to pickup the signal and the inside antenna to broadcast.
View 2 Replies
View Related
Aug 4, 2011
Will this router ever see a firmware update so that we can have some additional functionality? The version of Twonky Media server that was bundled with this router was old to begin with, and now we are stuck with it? I tried the E4200 but it just kept spinning my drive that's parked in a ThermalTake BlackX, at least the 3000 doesn't do that, but when can we expect some new firmware, it's been 8 months. I used to love Linksys, but with this kind of support I may have to move to a different brand, and I bet I am not alone. it doesn't break the E3000 like you broke the 4200.
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Apr 21, 2013
My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies
View Related
Aug 14, 2012
The wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
View 5 Replies
View Related
Oct 11, 2012
I have experienced some strange behavior of WiFi connection using WRT320N router. ISP provides me the internet in 2 modes (day and night). During day mode max speed is 24 Mb/s and during night 60 MB/s. Modem ADSL (Cisco EPC3010) is connected to Linksys WRT320N and on router is configured WiFi.Now issue. In the day mode everything is perfect. Cable connection gives me 24 MB/s and WiFi connection around 22 MB/s so not so bad. However when my internet speeds up to 60 Mb/s (cable connection via router gives exactly 60), WiFi connection instead speed up as well, just drop to max 17 Mb/s. I have tied several different settings on the router including changes in WiFi band, channel width, different channels (now channel is setup to 1 which is maybe not totally free but no so occupied) and others but unfortunately without significant improvement (in many cases connection just slowed down more).
And some details:
Wireless configuration (now)
Band: 2.4GHz
Mode: Wireless-N only
Channel Width: Auto (20MHz or 40 MHz)
Channel: 1
Wireless adaptor: Intel Centrino Advanced-N 6230 (I know that this doesn’t mean anything but Win7 shows that connection is established with speed 144MB/s)Router firmware and WiFi card updated to the newest version.
View 9 Replies
View Related
Aug 28, 2011
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
View 2 Replies
View Related
Jun 13, 2012
Have to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies
View Related
Apr 7, 2012
If the wifi can be turned off on the E1500. I got this unit from a family member and do not need the wifi part, as I have two computers, but are in the same room. I have the cisco connect on my computer and do not see a disable wifi in the program anywhere.
View 1 Replies
View Related
Dec 21, 2012
I just purchased a e1500 to replace my wrvs4400n which sadly died. yea I do loose a lot of features. I set up everything without a hitch but when I try to use Wireless-N mode only, none of my computers can connect to the router and all my computers use N cards. I'm stuck on using Mixed Mode which limits my speed to G speeds. I didn't purchase this to be a G router but an N router and it seems N mode has issues. I am on the current firmware.
View 9 Replies
View Related
Jun 1, 2011
I recently purchased the Linksys E1500 and at first, had no problems with it. The last few days I've had issues however. I tried logging into the internet and my WIRED computer would not connect. My wifes WIRED computer next to mine didn't have any trouble connecting. Resetting my computer didn't work. I had to cycle the router by unplugging it! Then today, my (2) kids are using Pandora on their (2) computers wirelessly, and same set up with my wifes computer and mine, and again only my computer looses access from the router and all other computers stay connected.
View 9 Replies
View Related
Dec 22, 2012
I followed the directions at least 6 times and I still had no internet connection. Is this because I have Windows 8 and all directions are for windows 7? I finally gave up and hooked back up our 6 year old belkin wi fi router. Had internet access in 1 minute. I bought this wi fi router was because Amazon described it as simple, quick, automatically does the work of hooking it up for you. Takes less than 5 minutes.
View 2 Replies
View Related
Jan 9, 2013
I want access to my e1500 with using a password
View 1 Replies
View Related
Dec 7, 2011
So I just got this router in hopes that I would get a better signal within my room as opposed to my older router. Unfortunately, nothing has changed, in fact I think I'm getting weaker signals. My previous router was a D-Link WBR-2310. I went to speed test.net and tested 3 variables. My wifi on my desktop in my room, my wifi when right next to a router on my laptop, and my wifi using my neighbors wifi in my room.
My room Desktop Wifi:
Download was 0.50 mbs Upload: 3.6
My laptop right next to Router:
Download 19.87 mbs Upload: 3.5
My room Desktop Neighbors Wifi:
Download was 17.3 mbs Upload was 3.32.
What is the point of this new wireless N router, when it can't beat a G router older model in reach? And why does is have a 0.50 mb d/l speed but a 3.6 upload speed?
View 4 Replies
View Related
May 12, 2012
I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N? I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
View 1 Replies
View Related
Aug 16, 2012
I just purchased an E1500 router to create a wireless connection. I had been using an older Cisco model previously.
I can't get it to connect. I have tried everything that is written in the support articles. In particular, I followed the article 3686, about setting up a router with cable internet modem, after the Cisco Connect didn't create the connection automatically.When I plug the laptop directly into my modem, I have a connection. I have reset the modem and the router several times in the process. I've been to the web-based setup page and followed all of the instructions about cloning the MAC. When I hit the release and renew IP addresses (under the Status tab), nothing happened. They remained 0.0.0.0
Called my ISP, but they say it's a router issue.I think I'm going to start from scratch--uninstalling the Cisco Connect, reinstalling it, turning everything off and back on again to see if it somehow will work automatically.
View 4 Replies
View Related
Aug 24, 2011
I just purchased a new linksys e1500 and followed the steps on the cd to set it up. I have internet access on my windows 7 laptop and iphone however, I have "local access only" on the two laptops we have running vista. The router is working fine for the windows 7 machine and the iphone but I cannot connect to the internet on the two vista machines.
View 9 Replies
View Related
May 5, 2012
I have a E1500 hooked to a Galaxy Broadband/Hughes Satellite internet system. From the router I have gone to a EZXS55W ver. 4 switch. Off of the switch I have 2 computers and a PoS machine. The satellite system gives us a dynamic IP. I am noticing that my connection from computer to computer and also from them and the POS machine to the internet is constantly switching on and off, it seems. Any ideas what could be causing this issue?? We just recently went from a Static IP to the Dynamic IP. We did not have this issue with the Static IP and wondering if there are some settings I have neglected.
View 1 Replies
View Related
Aug 17, 2011
I ordered a linksys E1500 for a home office. There are 3 computers that connect wirelessly: a 8-year-old desktop with a Netgear USB adapter, a 1.5 year old laptop and a 3.5 year old netbook, both with internal wireless cards. The desktop and netbook are running Windows XP and the laptop runs WIndows 7.
The desktop (XP) and laptop (Windows 7) are able to connect with no problem. However, the netbook (XP) is having problems connecting. It is able to connect to the router using the WPA2 key, and says it has excellent signal. However, when I start up an internet browser, it gives me a DNS error for any page I try to access. Connecting directly to the router with a cable works fine.
I got on the phone with Linksys support. They told me the problem was that the computer wouldn't use WPA2, but when I switched to WEP, it didn't work at all! I switched back to WPA2 and have the same problem as before: it connects to the network but DNS error messages for any website I try to access (And I've tried both Chrome and Explorer).
To make things more interesting, I set up a guest network on the router, and the netbook connects fine through that so far!
View 1 Replies
View Related
Feb 18, 2012
Which one have the best range ? I know that the E1500 has SpeedBoost feature but does it matter ? I can get both for the same price.
View 1 Replies
View Related
Mar 23, 2013
I have an E1500 N300 Router, I've had it for 3 or 4 weeks now. Ever since I've had it, I can no longer send e-mails out with Eudora nor Outlook. I've tried using about 3 different SMTP's just to verify that it wasn't a server issue. I tried Port Forwarding in the router settings. I selected SMTP and POP3 and checked Enable on both, then save changes. But they don't appear to be taking, as when I go back in and try to set them again, it let's me and doesn't give me a Port Overlap warning. I've been told that I shouldn't need to mess with Port Forwarding at all, I just need to go into the Firewall settings and open up the SMTP, POP3, and IMAP ports. However, I don't see any settings in my Router settings to allow this, aside from Port Forwarding and it's not actually saving the changes. I will admit, I'm not all that great with this stuff, and this is the first time I've had any issues with a Router stopping me from E-mailing.
View 9 Replies
View Related
Nov 18, 2011
Just bought an E1500 wireless router -- when setting the router name and password, a 2nd guest sight came up, but I had to leave the computer, and when I came back that page was not there. I do have a guess password, that is fine---what I want to remove is the guest signal to our Dish Network wireless sight.
View 2 Replies
View Related
Mar 22, 2012
i got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies
View Related
May 10, 2013
I'am using router E1500 in a bridge mode (aka WiFi access point N standart). I want have two chanel transmitions, but i see only one chanel. In a specification write 2T3R (up to 300 Mbps).
View 6 Replies
View Related
Jun 26, 2012
I recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies
View Related
