If the wifi can be turned off on the E1500. I got this unit from a family member and do not need the wifi part, as I have two computers, but are in the same room. I have the cisco connect on my computer and do not see a disable wifi in the program anywhere.
View 1 RepliesI have tried everything and every connection suggested and still can not get a wireless conection.
View 2 Replies View RelatedHave to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies View RelatedI just purchased a e1500 to replace my wrvs4400n which sadly died. yea I do loose a lot of features. I set up everything without a hitch but when I try to use Wireless-N mode only, none of my computers can connect to the router and all my computers use N cards. I'm stuck on using Mixed Mode which limits my speed to G speeds. I didn't purchase this to be a G router but an N router and it seems N mode has issues. I am on the current firmware.
View 9 Replies View RelatedI recently purchased the Linksys E1500 and at first, had no problems with it. The last few days I've had issues however. I tried logging into the internet and my WIRED computer would not connect. My wifes WIRED computer next to mine didn't have any trouble connecting. Resetting my computer didn't work. I had to cycle the router by unplugging it! Then today, my (2) kids are using Pandora on their (2) computers wirelessly, and same set up with my wifes computer and mine, and again only my computer looses access from the router and all other computers stay connected.
View 9 Replies View RelatedI followed the directions at least 6 times and I still had no internet connection. Is this because I have Windows 8 and all directions are for windows 7? I finally gave up and hooked back up our 6 year old belkin wi fi router. Had internet access in 1 minute. I bought this wi fi router was because Amazon described it as simple, quick, automatically does the work of hooking it up for you. Takes less than 5 minutes.
View 2 Replies View RelatedI want access to my e1500 with using a password
View 1 Replies View RelatedSo I just got this router in hopes that I would get a better signal within my room as opposed to my older router. Unfortunately, nothing has changed, in fact I think I'm getting weaker signals. My previous router was a D-Link WBR-2310. I went to speed test.net and tested 3 variables. My wifi on my desktop in my room, my wifi when right next to a router on my laptop, and my wifi using my neighbors wifi in my room.
My room Desktop Wifi:
Download was 0.50 mbs Upload: 3.6
My laptop right next to Router:
Download 19.87 mbs Upload: 3.5
My room Desktop Neighbors Wifi:
Download was 17.3 mbs Upload was 3.32.
What is the point of this new wireless N router, when it can't beat a G router older model in reach? And why does is have a 0.50 mb d/l speed but a 3.6 upload speed?
I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N? I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
View 1 Replies View RelatedI just purchased an E1500 router to create a wireless connection. I had been using an older Cisco model previously.
I can't get it to connect. I have tried everything that is written in the support articles. In particular, I followed the article 3686, about setting up a router with cable internet modem, after the Cisco Connect didn't create the connection automatically.When I plug the laptop directly into my modem, I have a connection. I have reset the modem and the router several times in the process. I've been to the web-based setup page and followed all of the instructions about cloning the MAC. When I hit the release and renew IP addresses (under the Status tab), nothing happened. They remained 0.0.0.0
Called my ISP, but they say it's a router issue.I think I'm going to start from scratch--uninstalling the Cisco Connect, reinstalling it, turning everything off and back on again to see if it somehow will work automatically.
I just purchased a new linksys e1500 and followed the steps on the cd to set it up. I have internet access on my windows 7 laptop and iphone however, I have "local access only" on the two laptops we have running vista. The router is working fine for the windows 7 machine and the iphone but I cannot connect to the internet on the two vista machines.
View 9 Replies View RelatedI have a E1500 hooked to a Galaxy Broadband/Hughes Satellite internet system. From the router I have gone to a EZXS55W ver. 4 switch. Off of the switch I have 2 computers and a PoS machine. The satellite system gives us a dynamic IP. I am noticing that my connection from computer to computer and also from them and the POS machine to the internet is constantly switching on and off, it seems. Any ideas what could be causing this issue?? We just recently went from a Static IP to the Dynamic IP. We did not have this issue with the Static IP and wondering if there are some settings I have neglected.
View 1 Replies View RelatedI ordered a linksys E1500 for a home office. There are 3 computers that connect wirelessly: a 8-year-old desktop with a Netgear USB adapter, a 1.5 year old laptop and a 3.5 year old netbook, both with internal wireless cards. The desktop and netbook are running Windows XP and the laptop runs WIndows 7.
The desktop (XP) and laptop (Windows 7) are able to connect with no problem. However, the netbook (XP) is having problems connecting. It is able to connect to the router using the WPA2 key, and says it has excellent signal. However, when I start up an internet browser, it gives me a DNS error for any page I try to access. Connecting directly to the router with a cable works fine.
I got on the phone with Linksys support. They told me the problem was that the computer wouldn't use WPA2, but when I switched to WEP, it didn't work at all! I switched back to WPA2 and have the same problem as before: it connects to the network but DNS error messages for any website I try to access (And I've tried both Chrome and Explorer).
To make things more interesting, I set up a guest network on the router, and the netbook connects fine through that so far!
Which one have the best range ? I know that the E1500 has SpeedBoost feature but does it matter ? I can get both for the same price.
View 1 Replies View RelatedI have an E1500 N300 Router, I've had it for 3 or 4 weeks now. Ever since I've had it, I can no longer send e-mails out with Eudora nor Outlook. I've tried using about 3 different SMTP's just to verify that it wasn't a server issue. I tried Port Forwarding in the router settings. I selected SMTP and POP3 and checked Enable on both, then save changes. But they don't appear to be taking, as when I go back in and try to set them again, it let's me and doesn't give me a Port Overlap warning. I've been told that I shouldn't need to mess with Port Forwarding at all, I just need to go into the Firewall settings and open up the SMTP, POP3, and IMAP ports. However, I don't see any settings in my Router settings to allow this, aside from Port Forwarding and it's not actually saving the changes. I will admit, I'm not all that great with this stuff, and this is the first time I've had any issues with a Router stopping me from E-mailing.
View 9 Replies View RelatedJust bought an E1500 wireless router -- when setting the router name and password, a 2nd guest sight came up, but I had to leave the computer, and when I came back that page was not there. I do have a guess password, that is fine---what I want to remove is the guest signal to our Dish Network wireless sight.
View 2 Replies View Relatedi got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies View RelatedI'am using router E1500 in a bridge mode (aka WiFi access point N standart). I want have two chanel transmitions, but i see only one chanel. In a specification write 2T3R (up to 300 Mbps).
View 6 Replies View RelatedI recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies View RelatedI am not getting anywhere near the same download speeds to my wireless laptop as my wired desktop? When I run the Xfinity speed test on my wired desktop I get anywhere from 18MB to 40MB downloads.But the same Xfinity speed test to my Wireless connection to my Dell laptop [G adapter] never gets above 15MB.Is there a checklist anywhere I can use to maximize my wireless speed to a [G adapter] wireless device?
View 9 Replies View RelatedI have Vista Home on a laptop (all up to date) and when I try to set up wireless connection using a key it goes to 25% then times out. When I try to manually set up a connection I get limited connectivity and no internet. I have one other laptop with Win 7 and this connected with no problems, also one desk top connected with no problems. Kept getting the error 82BD0119 on the Vista laptop.
View 5 Replies View RelatedDevice: Linksys E1500 - firmware: 1.0.01? I've got a static IP setup for a small remote office and want to keep tabs on their internet connection by pinging it via a monitoring program we use. However, the router seems to not responding to ICMP.
- Filter Anonymous Internet Requests is unchecked.- I've verified that the Static IP is correct.
- I've tried pinging from several remote locations on different connections, with no avail.
I can't seem to figure out why i can't ping this device. I just want to make sure there isn't a setting in the wireless router that is preventing echo replies.The only other thing i can assume is that Comcast is filtering ICMP on their side of the WAN connection.EDIT: Here's a traceroute from my PC to the WAN side of the Linksys....
Tracing route to 50-194-XXX-XXX-static.hfc.comcastbusiness.net [50.194.XXX.XXX]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 172.25.2.1 2 6 ms 16 ms 6 ms 10.0.0.5 3 9 ms 8 ms 8 ms 10.0.0.1 4 7 ms 7 ms 7 ms 10.0.0.2 5 8 ms 7 ms 7 ms ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX] 6 7
[code].....
I just bought a Linksys E1500 router and followed the CD instructions for setup. It is wired to my desktop and I am unable to access the internet. If I go direct to the modem and bypass the router the internet works fine
View 3 Replies View RelatedHow do i setup my Linksys E1500 router as an access point? I have a main router upstairs but the signal is weak in the basement. How do i configure this router as an access point for internet?
View 2 Replies View Relatedmy router stop getting internet connection its plugged in but keeps telling me no reset modem or unplug router
View 4 Replies View RelatedI am trying to find out what devices are connected to my router. I have had some illegal downloading from my IP address but it has not been done from my computer. It is showing in Cisco Connect that I have 15 devices connected, I should have no more than 6 devices connected so trying to figure out who is connected on my computer.
View 9 Replies View RelatedI've been researching this for a day now and have just confused myself further. Long story short, I just picked up an EA4500 and there's still a dead area in the house. I already have one ethernet cable that's being used which runs from the one side of the house to the other. After researching this, I believe I can set up the E1500 as an Access Point to further the range of the wireless signal via the ethernet cable and 2 routers. I just have a few additional questions that the articles and walkthroughs I've read through didn't seem to address.
I set up the EA4500 and have 2 SSID's, one for 2.4Ghz and one for 5Ghz band. When I set the SSID on the E1500, should I use the 2.4Ghz SSID from the EA4500 or should I reset the EA4500 to factory defaults and only use the 1 SSID instead of splitting them? Or, should I use a totally different SSID altogether on the E1500?I think from what I read, you should use different channels for each router; does it matter which ones you use as there's not that much traffic in my area and do I need to change the channel on both bands of the EA4500? Or can these all be left to Auto?Can you still use the ethernet ports on the AP/E1500 or are they rendered useless if you set it up in this mode?
I bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload Details About Router & Connection,Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.
View 1 Replies View RelatedI have my wireless set up in my house. All other computers and devices can connect and get on the internet fine, except my laptop. I can connect to the wireless routers network but it says local only and wont let me on the internet. I tried using the cd to install the router settings on the computer but it never goes past 25% and gives me this information:Error code: 82BD0119Error description: The adapter connection timeout period expired.Model name: Linksys E1500Model number: E1500Serial number: (Removed)Firmware version: 1.0.01 build 4Operating system: Windows Vista SP 2Software version: 1.3.11027.1Connection type (WAN): DHCPIP address (LAN): 192.168.1.1IP address (WAN): 71.61.221.251Computer IP address: 0.0.0.0
View 1 Replies View RelatedI have a Linksys E1500 wireless router that I have had for about 3 months and it has been working great up until today. I realized non of my wireless devices could detect the network, so I got on my PC which is hard wired to the router and it to says it had no network connection. So I power cycled both the router and the modem. When it came back up, this PC that I am typing from now has an internet connection but is says it is connected to Network 2 instead of the routers name for the network. My other PC that is hard wired to the router says its not connected to the network, and when I open up the Cisco Connect software it tells me my router is not plugged in. Also, nothing works wirelessly.In the web control panel it still has all my setting intact but still looks like its not connected to the internet.
View 1 Replies View RelatedI have upgrade firmware of E1500 to latest release to version 1.0.04 and found out bad performance of the router QoS.
View 6 Replies View Related I have a linksys 1500, connected to a cablemodem. It has firmware 1.0.04 (but this problem happened with earlier firmware that it shipped with).I have a problem with the DHCP server on the E1500 - or maybe its a bad client - one of my clients, happens to be an iPad-2 doesn't seem to get properly connected. all of my other wireless DHCP clients - windows vista, windows 7, linux, android, mac and an old iPad1 all connect without problems. I also have wired devices that get their IP via DHCP for my TV, blu-ray, slingbox, DVR, without problems, its just this iPad2 that tries to connect, seems that it does, but can't access anything on the internet.I see this on the DCHP Client list (Status -> Local Network -> DHCP Client Table from the web interface) and I'm quite sure this is the cause of the problem with the iPad2. that MAC address is the address of my iPad2, and that IP# is the one I reserved for it.
I've set up that MAC address to have a reserved IP#, and forced the client name to Rays-IPad2 (as its named on the device) but it has the same behaviour as letting the DCHP server give it an IP# from its address pool. And if I reboot the E1500 and reboot the iPad2, it does actually connect for a few seconds, I can bring up a page in safari, etc, but soon within a few seconds, it switches the client name to this display of question-marks (non printable characters presumably) and it can no longer get to the internet.Is there anything I can do or try? There isn't another DCHP server running on the network, I don't know if something with the cable modem is causing a conflict, and if it were I'm not sure what I could do about that.
I'm using a Linksys E1500 on my Timewarner 20Mbs connection and I've noticed that anytime another computer on my network connects my connection speed take a significant drop. This happens when Macs or PCs connect and there doesn't seem to be any common ground between any of them. In addition the connection is slow wether the other PCs are idle or downloading anything, it seems to make no difference. my ping in any game drops from 70 to 500 just for 2 other PC being on at the saem time on the network.
View 2 Replies View Related