Linksys Wireless Router :: EA4500 Blocked User Accessing Log In Screen
Sep 7, 2012
I have the EA4500 router with cisco connect cloud, must say this router is great for limiting kids online.1 question I have however is the ability for a blocked user (internet access block) that is redirected to the cisco web site and presented with a log in screen. Is there anyway I can disable this becuase the kids stay up all night trying to figure out the password to log in, I just want it to say internet access blocked with no option for logging in for the blocked user.
EA4500 in bridged mode and I can log in the the CCC account but nothing appears on the screen. I was able to see the settings, etc with the previious firmware. I reset the router and tried different browsers, PC, etc. Now running Ver.2.1.39.144146.
I setup several devices in the Parental Controls to be blocked always. These devices are still able to connect to the router. I tried rebooting the router but the problem persists. I have two laptops and two iPod Touches that can connect regardless of the access restrictions.
I tried to log in into my EA4500 today, and instead of the simple window that asks for the user name and password, I am getting a Cisco Connect Cloud log in screen. It is very strange.
At the top it says: Cisco Connect Cloud/Powering Linksys Products
and below that:
Sign In If you have not yet created an account, click the 'Create Account' button in the upper right corner of the page
There is a help button, a button to create an account. There is a place where I can enter an email address and a password.
Pressing the Help button I learned that I can probably bypass this silly screen by disconnecting the internet. Is there a better way to bypass this screen and turn off Cisco Connect Cloud?
I have a 1TB Western Digital drive connected to my home EA4500 router. Connecting to media server using SMB protocol (192.168.1.1) works fine. I am moving abroad for an extended amount of time, though, so I would also like to connect to this USB drive using FTP. Using the new Cisco Connect Cloud interface, I have enabled FTP sharing for the USB storage device with port 21 and using standard UTF-8 encoding. Whenever I try to connect to the FTP server using my router login credentials, I get the following error message:"There was a problem connecting to the server xx.xxx.xxx.xx. This file server will not allow any additional users to log on. Try to connect again later"
I have mapped the attached hard drive to my EA4500 on my PC and can access folders and files on my LAN PC. However, when I come in through the Internet via an iOS device, I can see folders but when I try to enter the folder, all I get is a message that displays "|Folder|Enter Into Folder|Select|. There is no click-through capability other than "Return to Upper Folder", which takes me back to folders.
i have a cisco DPQ3925 , im trying to setup user access for my kids to prevent them from accessing the net , i have set up the time of day and the user setup , but cant get it so u have to logon with the set user names to access the net.
I work at a campus and use the WCS to control access to my network for staff and only internet access for students. The Staff are assigned Username/password thru active directory and the student uses another SSID with only WPA --a password for all. I was tasked with adding more securing for students -- by adding a user/password. I do not want them connecting to my Active Directory for two reason--security risk and I have too many to input (over 1000). So, I wanted to use our internal database to validate users. I create a webpage with "WebAuth" that opens my logon page from my site and validates the login fields against the database. It works and this allows the user to navigate thru my website but not outside the site. If they try an outside url it redirect them to my logon script. I now understand why, so I'm looking for code I can add to my logon page that would allow me to redirect me to the controller's (once users are authenticated by my database) to call the WCS controller so I can enter a preset username/password so the policy management file would allow them access. I presently use "External" and don't know if "Custom" would work. Finding a way in using a database instead of adding one person at a time?
I've a BEFW11S4 router that was working fine for 5 years, until the other days it would not let me go to url... but any other websites works just fine.
I've just discovered that my wireless router is not secure (WRT54GS v5). In trying to set up the propoer security, the set up screen appears as incomplete (after entering 192.168.1.1). It only shows 3 tabs at the top - Basic Setup, MAC Address Clone, and Advanced Routing. No tab to deal with the settings. I have tried resetting the router and plug/unplug several times. Triued entering thru IE and Firefox.Is there another way to set up the security on my router or at least get the proper screen?
I have a computer that is connected to a linksys wireless router model WRT160NV2. I also have a laptop. I have never set up a lock or anything on my wireless connection and I think other people are using it. When I type the IP address 192.168.1.1 on my laptop, I do not get the screen to pop up to change my settings. Do I need to do this from the computer?
how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
When I go to the router setup screen via 192.168.1.1 the screen does not load properly in MSIE or Firefox. Text does not load.The graphics load okay, and the dropdown boxes, checkboxes, etc. Since many of the links are from text, and all of the descriptions, it is impossible to navigate properly. I managed only by using Firefox's Page Info, Links tab and cutting & pasting. A couple of screen captures are available [URL] have downloaded the latest firmware, but while I can get to the Administration page, much less click on, the Upgrade Firmware sub-tab.
After popping in the installation CD, the screen says hook everything up, which I do. Then click next, where it says "Searching Networks", then quickly changes to "Connecting to Network", and then it says it "Cannot Find Router.". Err. Check setup, etc.If I hook up directly to new router VIA internet cable. Also, this is strange: When I just open up a web browser and try to log into the router 192.168.1.1, using no user name, administration as the password, it won't let me in to the router. Even after I have reset the router with a pen.
I have a wrt54G v8 wireless router and I was trying to install a firmware update a while ago and got impatient, stopped the upgrade in the middle of it and I think I may have bricked my router. I've since tried the 30/30/30 reset a number of times and have noticed that I don't get a blinking power light which I guess means it's ok.
Now when I go to 192.168.1.1 and log in, I can see most menus but when I click the firmware update menu (there's another screen that's also all white, I forget which one), it's all white (or blank). I've searched for a solution on the web and no luck so far.
I've been trying to do this on a mac and no luck. I then booted into windows 7 and used IE 9 to log into 192.168.1.1 and still the same thing, the firmware update screen is blank.
I have a Windows Home Server v.1 I set it up nearly a year ago, and everything runs fine.I have 3 different user accounts that are password protected.On my PC, i have been running Windows 7 and using the server as my My Documents folder.I recently installed Windows 8 Consumer Preview on an old Hard Drive, and i can't seem to access any folder on the server that isn't already given public permission. Whenever i try to access my User folder i get an access denied message, but no prompt to enter a password so i can use it.
I'm setting up WHS 2011 for the first time. When attempting to set up Remote Web Access, WHS continues to recoginze my E4200 model information and router IP address but delivers the message 'Remote Web Access to Your Server is Blocked'. Cisco and MS say the router is compatible with WHS and that it should set up through the wizard but no luck following many attempts, including manual set up of DHCP Reservation and Single Port Forwarding on ports 80/443 (not sure I did this correctly).
I've taken the router back to default settings with the exception of enabling Remote Management under the Remote Management Access section of the Administration menu tab; tried again with the same result. What settings to change to make this work?
I have a WRT120N with Firmware 1.0.06..First peculiarity is that I can't access the web based admin screen from Firefox 7.0.1. The password prompt appears but won't proceed from there.Second, and main issue is that frequently (several times a day) I get a 'Limited Access' error on my wireless connection. On mouse roll over Windows 7 Pro gives the error message 'no internet access'. This problem appears to resolve itself after several minutes or straight away if the router is powercycled. During these 'Limited Access' moments I am unable to connect to the route web based admin page nor ping or tracert. [code]
I installed this Linksys E1500 yesterday and have had a problem keeping my iPhone 4 and an iPod Touch connected to WiFi.The devices go to sleep. When I swipe the screen and "bring them back" the WiFi is Not Connected. I have to go in and re-enter my network password again. As long as the devices don't go to sleep, they maintain connectivity. Once connected they function properly.
The iPad 2 & Samsung Galaxy S phone we have seem to be keeping their WiFi connectivity, as well as a G62 HP laptop running Windows 7, an older XP machine using a Cisco AE1000 wireless network adaptor and the Xbox 360. The issue is just with the iPhone 4(ios 5) and the iPod Touch(ios 4).
I had issues with the iPad and the Galaxy phone until i disabled WMM Support in App & Gaming.I would bring this back to the retailer but I had it sitting on my desk for about 30 days and it's past their return policy.The firmware is up to date on the Router. I've tried power cycling all the devices including the cable modem & the new router.
I have been trying to get port forwarding to work for a week now with no luck. I use Centurylink for Adsl, modem is a zyxel 660r, router wrt54g, running windows 7.I have made my modem a bridge only. I have set my computer to a static ip. I have followed all the instructions for port forwarding on linksys. Still my ports show blocked no matter what check I use on the Internet.
is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.
I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was stoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to thenavigator for show the administrator´s window. Any procedure to recover the operation of the router in a situation like this?
I use a WRT54G wireless router connected to Mac. All of a sudden, I became unable to access certain websites on my iMac, such as Facebook and Apple homepages. But i can access Yahoo website. I tried resetting my linksys setup but it doesnt solve the problem. When i access my iphone via wifi at home, i am also unable to go into app store, facebook app, and emails with images won't load. I also cannot link my iphone to itunes on my iMac. What happens on my computer when I surf the internet is that the page just loads halfway and stop "responding". But my imac airport says that my internet connection is fine, however my access has become very "restricted".
I've got the below setup, have the wrt320 setup as a switch / wifi ap, i'm totally unable to access its management page from pc1 but am able to via pc 3, why is this, how can i get around this? Routing? Also am unable to access pc3's resources from pc1..When i enter the ip of the wrt320 it thinks about it and before it has come up with the user/password screen but it soon dissapears and firefox comes up with a "Unable to connect Firefox can't establish a connection to the server at 192.168.0.2." message.
I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
I was running a Linksys cable modem and 54G with dd-wrt. I had an LG NAS hooked up and everything was working great. I recently upgraded to the Motorola SB6120 and the Linksys E4200. I can not access my LG NAS from outside of my network now. UPnP is enabled, port forwarding is enabled, but I must be missing some other setting that is blocking me from accessing it from work for example.
I have a Motorola cable modem with 8 port switch connected to it. I also have E4200 and BEFW11s4v4 connected to the switch. I used BEFW's ports mainly to connect my direct box and blu-ray DVD player to the internet in a different room. I noticed a pretty good signal coming from befw11s4v4. I would like to turn it off or use this wifi b, but I forgot the passphrase to it and I can't install befw11s4v4 with E4200 active. (192.168.1.1 is taken by e4200). How do I get to it (befw11s4v4)? I don't want to reset befw11s4v4 because that would make its WiFi unsecured. I can use a laptop to install befw11s4v4 and change its IP to 192.168.2.1 for example, but I would like to be able to access both (E4200 and befw11s4v4) from my desktop PC.
I am using a LinkSys Model: WRT54G Version: 6 wireless router configured to use WEP.I have two computers, the main desktop and a laptop for mobile operation.How do I configure the LinkSys to allow the laptop to access a external (mapped) USB drive on the desktop?
The laptop can access the mapped drive on the desktop when it is hardwired to the LinkSys (i.e., not wireless) but I cannot find a reference in the Pdf manual or online on how to access the drive on the desktop from the laptop when the laptop is connected via the WiFi.The desktop is running XpSp3 and the laptop is Vista.A second and more important question is should I do this. Can the accessing of the drive via the WiFi be done with adequate security. I would rather err on the side of caution.
I just connected my WRT120N router to the modem of my Cable provider. Everything seems to work well, however every 1-3 days I cannot access internet anymore with my laptop. When I press "IP address release" button in the router settings everything seems to work fine for again 1-3 days. Is there any way I can prevent this from happening all the time?
I have a WRT54G2 version 1 router. I want to access it via internet remotely. I have a static IP and I enabled Remote Management option. I tried to access it from outside my home network entering my router static IP followed by :8080 in web browser. The username and password window appeared. After entering the right username and pass I just get a blank page
if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
