D-Link Powerline Homeplug 501AV / Configuring Two Router To Work?
Dec 6, 2012
I have the following network setup. I have a dynamic IP address from my ISP. I connect my fiber to a D-Link DIR-645 and set up my wireless network. The coverage is kind of poor in my son's room so I use a D-Link Powerline Homeplug 501AV to extend internet to my son's room. I connect one Homeplug to the DIR-645 and set the other Homeplug in the power outlet in my son's room. It works if I connect his PC or Xbox via an ethernet cable to the Homeplug in his room. Since he has both PC and XBox I have connected a D-LINK DIR-100 to the Homeplug and have two ethernet cables connecting to his PC and Xbox. Here is the problem. I don't get an internet connection to the DIR-100.How shall I configure the two routers to work?
View 1 Replies
ADVERTISEMENT
Jan 8, 2012
I have recently bought a homeplug to connect to the internet since my broadband is downstairs from my pc. I have plugged in the two homeplugs and connected them to my pc and broadband with a ethernet cable. When i turn on my pc the ethernet light turns on (same for downstairs) but after installing the software and trying to search for my wifi a message pops up saying "The homeplug adapter has NOT BEEN DETECTED. Please check your computer cables". So i did so, i chnaged the sockect moved the ethernet cable to a diffrent slot and still it says it has not been detected. This is very annoying and i really want to get it fixed.
View 17 Replies
View Related
Apr 17, 2013
Today I set up a home network:Cable router plugged in to......Homeplug network, (D-Link DHP-307AV/B 200 MBPS PowerLine Homeplugs) plugged in to a LAN port of......a spare adsl router configured as per here: Connecting Additional Routers | Tech Support Forum...with two desktop machines plugged into the LAN ports of the ADSL router.Both of the desktops have got similar specs, are equi-distant from the ADSL router, and are both connected using Ethernet, not wireless.One of them gets a 9MB/sec ADSL [URL]download, the other can't even bring the webpage up and times out if you ask Google to do a search.Taking out the adsl router and plugging the desktop straight into the homeplug gets a network speed of ~13MB/sec on [URL].Plugging a computer directly into the cable modem gives network speeds of ~40MB/sec on [URL] How can I improve on this, and have it so that both machines can access the Interwebnet at a decent bandwidth?
View 8 Replies
View Related
Jan 3, 2012
I just installed a E4200, and found that once I connected my Homeplug Powerline to E4200, the connected (wired / wireless) computer (with E4200) connection will be dropped. The connection become normal again once I disconnected the Homeplug with E4200.
View 5 Replies
View Related
Sep 18, 2012
I just got E4200 and it seems my homeplug is not able to connect to router. I don't see it listed in DHCP Table under status. I could only see my Desktop was connected. Are these two not compatible? Homeplug works fine my old router which is Trendnet TEW-452BRP.
View 3 Replies
View Related
Jun 18, 2012
I have a D-Link DIR-655 version B1 Just installed firmware 2.03 Use a cable modem (Comcast) Motorola SURFboard model SB6120 Am trying to use Netgear 85Mbps Wall-Plugged Ethernet Adapter XET1001 to carry signal from the room where the cable modem is to another part of the house where I hope to connect the D-Link.
View 14 Replies
View Related
Mar 30, 2012
Got road runner already get internet with wifi router, but want to set up password protection for internet access. the wifi is default now.
View 1 Replies
View Related
Oct 17, 2011
I'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.
For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)
View 4 Replies
View Related
Jan 21, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : India
Model : TL-MR3040
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Reliance
Configuring my TL_Mr3040 with Huwei EC 150 model USB modem, the modem and ISP name is there in the list , I have configured all (manual/ as well as auto ) methods of authentication as mentioned in user guide.
for more infor , the exported profile from laptop where my modem works fine is
<?xml version="1.0" encoding="utf-8"?>
<utpsdoc type="Profile">
<ProfileGroup type="DialUp">
<Profile name="Reliance" type="" readonly="" device="" user="74831*****" password="74831*****" phonenumber="#777" autoapn="true" apn="" chap="true" pap="false" ip="" dns="" dnsalt="" wins="" winsalt="" imsi="" langid=""/>
</ProfileGroup>
</utpsdoc>
View 1 Replies
View Related
Feb 3, 2013
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
View 5 Replies
View Related
Jun 16, 2012
I have a Linksys WRT54g router that works fine, but the signal is not very good on some points of the house.So I bought a TP-Link 740n to use as a second router. My idea is to connect both routers with a 10 meters lan cable that I have, to make the signal better on points that are distant from the main router (Linksys) or separated by walls. When job is done, will I see two different networks (one for each router) on my laptop or only the "original" signal (WRT54g)?
View 5 Replies
View Related
Mar 2, 2013
I have a problem configuring port forwarding to 443 and having client VPN to work.When 443 is NOT forwarded, VPN just runs fine (QuickVPN).As soon as I enable 443, the VPN stops working. No client can connect.I have the latest 1.2.0.9 firmware.Is there a way to enable 443 and having VPN to work at the same time ? I need 443 for Exchange.
View 4 Replies
View Related
Mar 20, 2013
My next door neighbour has just installed a Virgin Super Hub and has 2 Homeplugs on his network. I have a Netgear router and 2 netgear homeplugs on my network, His network is giving my wireless router an IP address which changes my default gateway. Can I stop this by changing my default gateway and subnet mask? if so how and what to?
View 8 Replies
View Related
Jan 18, 2012
I need configure HTTP Compression by hardware on CSS 11503. I make config like this [URL]
My config:
service s1
ip address 10.1.66.11 (web server)
keepalive type none
[Code].....
View 4 Replies
View Related
Apr 30, 2011
if it would be possible to use a powerline adapter to connect a to second router? I'm currently hardwired like this, but I'm just wondering if powerline would work the same way, as I'd like to switch which room the wireless is running from.
View 3 Replies
View Related
Aug 17, 2012
I recently factory restored my new PC and we also got a new Virgin Media Superhub (Super Fast - My dad is getting download speeds of up to 4mb/s) but I tried using my powerline adapter thingy and I am getting crappy speeds and it says I am connected to a homegroup, and not my internet like it used too.
View 1 Replies
View Related
Jul 10, 2011
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies
View Related
Oct 27, 2011
I have two buildings on my property that I need to network together. One is my home about 3500 Sq. Ft. and the other is a garage about 3000 Sq. Ft. The two buildings are about 250 feet away from each other. Both are fed from the same utility pole that is half way between them. That means both are on the same transformer, but each has its own metered electrical service.Right now I am using 10 Mb. Home Phone Line network adapters. They work OK but data speeds are limited to about 5 Mb. of throughput and the adapters are no longer available. I also have WiFi at both locations but neither one will talk far enough to cover the other building.I also use X10 remote controls in my house. I have tested them from the house to the garage and they do not work at all over that distance
View 7 Replies
View Related
Jan 2, 2013
Just finally updated my ancient belkin modem to a Netgear D3600WiFi modem router which works really well. However. I have a old G5 Mac without wireless so have always connected through my old belkin modem with Powerline adapters over my house wiring circuit:confused. Unfortunately the powerline adapters no longer work although both lights are flickering on the units. Netgear say they should work.
View 1 Replies
View Related
Sep 14, 2012
I have a beautiful old home but, the walls are thick and WiFi signal dies easily. Is a Homeplug system safe for my old home? I am hoping to convert our current upstairs router into an access point/repeater for the downstairs router via DD-WRT. The issue is that the upstairs WiFi is on the 3rd floor and the downstairs in on the 1st and I will not be stringing an Ethernet cable through the walls.
View 1 Replies
View Related
Aug 16, 2012
My problem is that my son will not turn off his xbox at night. To get around this I want to connect the Xbox to an old netgear router that I am using as an access point to extend wireless coverage, so that I can use the parental controls on the netgear as the ones in the Sky Sagem are not adequate.I can disconnect the Netgear at a certain time if necessary and if this is the only way the xbox can connect it will have to go offline then!
View 4 Replies
View Related
Feb 18, 2011
I can't get the email to work from the router. It worked flawlessly for weeks then stopped working. I verified that the outgoing settings are still valid and that my antivirus is not blocking the email.
View 7 Replies
View Related
Aug 8, 2009
I have a DIR-825 since a couple of days, Hardware version B1, firmware 2.01EU (date Fri, 12, Jun, 2009 = latest european firmware) Have portforwarding for ports 25, 80, 443, 143, 993 via virtual server to a local linux server (192.168.0.3)
My (SIP protocol) VOIP phone (192.168.0.100) does not work anymore since I use this router. It worked fine on my old WRT54G. The phone logs-in normally at the voip provider but when I make a call, it seems that the ports are not forwarded or are blocked by the firewall. I have tried to manually setup portforwarding and virtual server instead of portforwarding.
I have tried many things, from disabling QOS, SPI, end point filtering and more but it does not work. I have also programmed DMZ for my ip-phone, but it does not work. Nothing found in the logfiles about frame drops. (I have setup a syslog on my linux-server)
There seems to be a bug causing frames dropped, as my setup has always worked with my WRT54, and should work with DMZ set, but it does not. The same setup works fine on a DIR-655 of a friend.
View 14 Replies
View Related
Jan 15, 2013
Region : New Zealand
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP : Telecom New Zealand
getting the MR3420 but will be using a ZTE 669 Turbo stick as the modem ISP Telecom New Zealand.I did notice that they seem to be supporting the ZTE 668+ which I'm guessing is a vary similar model.
View 3 Replies
View Related
Mar 4, 2013
Region : Malaysia
Model : TL-MR3040
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Celcom
Isn't MR3040 is supposed to work without battery with just AC power? Mine works fine with battery but without battery it keeps on restarting..
View 6 Replies
View Related
May 10, 2012
A friend of mine has given me a D-link DIR-615 Wireless Router. I only have a copper 10 meg ADSL service. The Router Internet socket is an RJ45, the ADSL Filters are RJ11. Is it possible to get this router to work on an ADSL Filter ? Can you get ADSL Filters with both an RJ45 and BT Phone connection on them, or a converter lead which converts RJ45 to RJ11 to work on the current ADSL filter?
View 5 Replies
View Related
Mar 29, 2013
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
ISP : Cellcom 3g - Israel
My USB Modem HUAWEI E173 not work as well with TL-MR3420 Its lose Identify every almost 15 minutes , and try to Identify again and some times not successfully until I reboot the unit . then its Identify successfully , after some minutes the problem happen again and again . I think its from the router software issue that it have not the correct driver of the modem .
also , the signal of the wireless not that good like the other routers which I used before .
View 8 Replies
View Related
Mar 19, 2013
Region : UnitedStates
Model : TL-MR3020
Hardware Version : V1
Firmware Version : latest
ISP :
I have problem to get pptp working. I setup pptp VPN server on my home router and configured pptp dialup on my laptop. If my laptop connect to internet directly, I am able to connect to home router via PPTP VPN. However, if I connect TL-MR3020 to internet(wired) and then connect my laptop to TL-MR3020 wirelessly, I can browse internet without problem. The problem is I cannot connect to home router via PPTP VPN any more. I believe the problem is on TL-MR3020.
View 4 Replies
View Related
Jan 24, 2013
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
View 14 Replies
View Related
Feb 1, 2013
Region : Peru
Model : TL-MR3040
Hardware Version : V1Firmware Version : latest
ISP : Movistar
Is there any chance to make work HUAWEI E303C with MR3040?I know this model is not in the compatibility list, but when I try connect this modem with the router, it can be identified but it cant be connected. On the logs it appears that there is a problem with dial, APN, but I'm sure I'm introducing the correct values?
View 1 Replies
View Related
Mar 18, 2013
Region : Germany
Model : TL-MR3040
Hardware Version : V1
Firmware Version :
ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...
View 3 Replies
View Related
Dec 24, 2012
Region : India
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
View 3 Replies
View Related
May 25, 2013
I recently modified my home network in hopes of getting faster file transfers between devices. But it looks like something's not right.I'm suing Lan Speed Test and the best performance I get over WiFi is about 44Mbps (avg.). From my laptop to my NAS. If i turn off the WiFi and do the test over a wired connection the best I get is 200Mbps (avg.).
1. AT&T 2Wire cable modem. Internet comes in the house through this box and it's currently set up to be in bridge mode so that the TPLink router handles everything.
2. TP-Link WDR3600 gigabit/wireless router set to work in 5Ghz only, 11an mixed mode.
3. WD My Book Network Storage. Wired gigabit connection.
4. Desktop PC. Wired gigabit connection.
5. Laptop PC. Wireless.
6. 1 ipad v.2, 2 iphone v.5. Wireless.
Current setup:
1. internet cable goes into 2Wire Modem.Wireless on this device is OFF.
2. cable goes from LAN port on modem to WDR3600 router's internet port
3. cables go out from router to Desktop PC and NAS
4. all other devices are connected to the 5GHz wireless network created by the router.
View 1 Replies
View Related
