D-Link DIR-655 :: Hookup A Usb Cable To Get Router Settings
Apr 10, 2011
I have been trying for days to get a HP Photosmart Plus B209a wireless printer to work with my D-Link DIR-655.Going through the HP setup cd for I get to the section where it wants to hookup a usb cable to get router settings and finds my network and then I put in the password. Then after looking for a bit it says it can't find the printer.Looking at the wireless status page it says the ip address is 0.0.0.0.Reading on HP's website it says that you must have the router set to broadcast the SSID, I believe mine is set to hide. How would I go about changing it to broadcast AND would it mess up all my other settings changing it to Broadcast, meaning will I have to reconfigure the other computers again? Do I use the set up wizard to edit things or is that for first time set up ?
View 5 Replies
ADVERTISEMENT
Nov 8, 2011
Have high speed cable and find that the wireless speeds using Speedtest.net are faster than when hooking directly into the E4200. Do I have something set incorrectly?
View 3 Replies
View Related
Apr 22, 2013
I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
View 1 Replies
View Related
Dec 22, 2011
I have a Linksys x2000 and have been using it successfully on DSL with a local ISP. I recently changed to Century Link and now I can't connect to the internet (Century Link). If I change the UserId and Password from my Century Link values back to my old ISP values, I can connect to my old ISP. Century Link tells me they have my account active with the X2000 and Century Link.
View 2 Replies
View Related
May 7, 2013
I plugged the printer into the DIR-655 and downloaded Shareport. Nothing. HP Laserjet 1320
[URL]
If Shareport can not be used, which one of the programs on that page might work?
View 5 Replies
View Related
Jun 18, 2011
I'm trying to login to my cisco 2621XM router. I'm using putty and I can't remember the how to cable it or the settings to use in putty. I don't have a db9 input on my pc, so I need to go through my NIC. What type of cable to use, what port to plug it into on the router, and what settings to use in Putty.
View 1 Replies
View Related
Nov 24, 2012
I am trying to hook a second computer up to run off my belkin router?
View 1 Replies
View Related
Mar 5, 2012
my password isn't working for wireless router hookup.
View 1 Replies
View Related
May 30, 2012
I tried to use my Netgear 614 router to my Netgear 3300 as an access point to gain range. But now I think I've screwed up the IP address(s) and have lost my wifi ability.
View 7 Replies
View Related
Jan 26, 2012
I have a wireless connection with my laptop.on a Belkin G router but can't get it to hookup to my Kindle Fire.what do I need to do?
View 2 Replies
View Related
Dec 23, 2012
I recently bought a practically brand new HP LJ P1006 with an extra brand new HP brand toner cartridge for $1 at a local auction. I have tested it, and it works perfectly, so all is fine there. I would like to know if it is possible to print wirelessly to it at all. I do not have it hooked up to a computer right now, we only have two laptops, so there is not a desktop to have it hooked up to in order to put it on a home network (I believe that is how that works).
I do have a Netgear N300 router with a USB port however, and I was thinking I may be able to do something there.
Is it possible to hook this printer into my router via USB and then be able to print to it from our latptops? If so, how would we go about setting that up to do so?
View 3 Replies
View Related
Jul 20, 2011
why I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page.
View 3 Replies
View Related
Sep 12, 2012
I forgot my router security code number but still working i want to need make new secure
View 1 Replies
View Related
Mar 14, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
View 4 Replies
View Related
Feb 23, 2011
Can I just plug the router into a 110 socket and then press the reset button to clear all stored information?
View 3 Replies
View Related
Nov 21, 2012
I have the DIR-655 (H/w Ver B1, F/W Ver 2.05NA) set up as router on my network (TWC/RR - modem is Motorola SURFBoard 6121 - modem only, no router or other services provided). I have configured the router sufficiently to allow all computers on the local network to access the Internet, and have configured the DHCP server on the router to provide IP addresses to the local network. I have configured the router to provide the DNS addresses for my local DNS resolvers (so that I can provide DNS resolution for an "internal" domain). Configuration specifics available on request, but everything mentioned so far is working satisfactorily, at least so far.
So, my question: The "Local Domain Name" setting on the router, as indicated in the documentation, provides a connection-specific domain name when DHCP supplies an IP address to the local system. This setting, however, is overridden if the ISP provides a domain name when it assigns an IP to the WAN connection. I have verified by experiment that this is true (no matter what I put in the Local Domain Name field - whether a valid domain, or blank - the local machines receive the domain name supplied by the ISP.I wish to modify this behavior. I wish to have the router provide the domain name specified in the Local Domain Name field *regardless* of what the ISP provides.
View 6 Replies
View Related
Jun 11, 2011
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
View 7 Replies
View Related
Feb 3, 2013
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
View 5 Replies
View Related
Nov 30, 2012
None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies
View Related
Jul 22, 2010
My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies
View Related
May 24, 2012
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies
View Related
Feb 2, 2013
Region : United Kingdom
Model : TL-WR841ND
Hardware Version : Not Clear
Firmware Version : 7.1
ISP :
failed to verify router settings
What's wrong with my router?
View 1 Replies
View Related
Dec 4, 2012
Region : Philippines
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : Smartbro WiMax
I'm using the router TL-WR2543ND, I have pesonally configured the router myself, I'm no that good in computer but I managed to do so. I never had difficulty doing it. I have decided to switch to Smartbro Wimax and tried to connect it to my tp-link router but no luck. I browsed the net for possible instructions to do it but just frustrates me. I have changed the IP address of the router to avoid conflict, cloned the MAC address, still unable to connect the router.
View 9 Replies
View Related
Jan 27, 2010
I have a WAG54G2 annex b and have a problem with the settings. The problem keeps emerging although I upgraded the firmware from 1.10 to 1.17.In details, almost once every day it keeps losing the settings, and although is is connected (I can browse web pages) the internet light is off, and in the admin page I can't see any settings at all. The language settings are lost, the wireless seems to be enabled, the connection settings don't show up, I can't see username/password/ip/dns and all my security restriciotns are lost. And i can't restore them until i reboot the modem, in which case everything is back like nothing has happened.
View 9 Replies
View Related
Sep 14, 2011
I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies
View Related
Mar 17, 2013
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.
View 3 Replies
View Related
Jul 10, 2011
Basically sometimes I suffer from serious lag! I want to best setting to get the most out of my modem. What are the reccomended setting for this modem?
View 1 Replies
View Related
Jan 16, 2012
my router is connected to main router from my internet provider. When I use x3000 my download speed is half as fast as it should be (wifi and wired). When I connect to mian router directly (without x3000) both wifi and wired connection is at full speed.Is there any setting I should use to get full speed on x3000 - I have 24 Mbit/s?
View 1 Replies
View Related
Dec 19, 2010
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?
View 5 Replies
View Related
Aug 25, 2011
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)
However ...when powering off (and back on) the device , my Dream box Satellite units (DM500) could not get access to the internet anymore (outbound) on port 12000.
All other internet traffic went fine ...through browser, wireless, ...all OK.....I tried everything to resolve but ultimately only succeeded in re-configuring from scratch. This solved the issue .....until ....right...I powered off the device and brought it back up ....same symptoms. Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all OK again .....until I powered the device off and back on .....
I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dream box unit directly to the device) and ....same symptoms ....when powering off/on, the dream box cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.
And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works OK ). It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ? (and ...no...I did not setup any port forwarding not triggering.
View 7 Replies
View Related
Feb 8, 2011
can i hookup a dsl phone lint to a linkss wireless router if i have wifi on my laptop?
View 2 Replies
View Related
Jun 30, 2012
I have a 2620XM router with a 16NM Layer 2 switching module installed,My question is once I get all my VLANs set up on the 16 port switch that I want. Do I need to connect a cable to the fast ethernet port on the router with its subinterfaces setup for routering across the vlans that I choose or can I connect them in the CLI?
View 19 Replies
View Related
Apr 2, 2013
I have meny concerns but one is intel Centrino Wireless 2230 2X2 bgn + Bluetooth a not so reliable wirless hookup?
View 1 Replies
View Related
