Linksys Cable / DSL :: WAG54G2 Can't See Any Settings At All
Jan 27, 2010
I have a WAG54G2 annex b and have a problem with the settings. The problem keeps emerging although I upgraded the firmware from 1.10 to 1.17.In details, almost once every day it keeps losing the settings, and although is is connected (I can browse web pages) the internet light is off, and in the admin page I can't see any settings at all. The language settings are lost, the wireless seems to be enabled, the connection settings don't show up, I can't see username/password/ip/dns and all my security restriciotns are lost. And i can't restore them until i reboot the modem, in which case everything is back like nothing has happened.
View 9 Replies
ADVERTISEMENT
May 30, 2011
I want to use WAG54G2 as plain router. I happen to have 2 of these. If i can make one of these work as router wired to another through ethernet cable or even wireless i can save some money on router.
View 8 Replies
View Related
Mar 23, 2013
Set up my WAG54G2 wireless gateway - I am able to connect to my LAN and the internet. The wireless works fine. However when I plug my server that use a wired connection into the modem/router,I lost the connection and I still unable to have internet at All. I use the firemware version V1.00.19.
View 6 Replies
View Related
Jul 6, 2010
How I can remotely reboot my WAG54G2 remotely either via telnet or through the remote web based management site. I dont seem to be able to find it anywhere and it is quite frustrating to not be able to do this remotely!
View 2 Replies
View Related
May 28, 2012
I need to use VPN from home to connect to my company. Company IT say that they can see my connection is successful but from home end it appears to fail (timeout). I'm using a CISCO WAG54G2 router. After attempting VPN access I have to re-boot router to establish broadband connection. I have checked Plusnet (ISP) firewall settings as okay (LOW). I have found two CISCO links which describe a similar(?) issue:
[URL]
I reviewed my router's Single Port Forwarding parameter settings in light of info in these links. I then added three new ones: VPN, VPN1, and VPN2 VPN; Internal Port:500; External Port 500; Protocol:UDP; IP:192.168.1.47; Enabled Yes VPN1; Internal Port:4500; External Port 4500; Protocol:UDP; IP:192.168.1.50; Enabled Yes VPN2; Internal Port:10000; External Port 10000; Protocol:UDP; IP:192.168.1.51; Enabled Yes
These changes have not worked but I not yet removed them. My company uses 'Delta VPN' product. No other changes to parameters have been made before or after.
View 9 Replies
View Related
Dec 15, 2010
i have the xbox and ps3 wired to the router and the laptop wirelessly to the router (if that makes any difference)
My router is the Linksys WAG54G2
View 9 Replies
View Related
Feb 2, 2013
I have ADSL router WAG54G2.I both new mobile, I can't put the mobile MAC address in "Wireless MAC Filter" because it is started with 5C:...The answer is "The MAC address cannot be the multicast address".
View 5 Replies
View Related
May 30, 2011
I happened to update firmware version of my WAG54G2 to the latest version 1.xx.xx.19. Since then connection to internet has became erratic. If rebooted, the device mostly doesn't connect. Switching to PPPoE from PPPoA and vice versa works but i have to do it every time the device is rebooted. Sometimes even that doesn't work. Basically it acts random. DSL connection shows as connected, but the internet interface is mostly down. I was wondering if i can switch back to to old 1.xx.xx.10 version. It never gave me any trouble ever for around 2 years.
View 4 Replies
View Related
Aug 31, 2009
I would like to know if I have to do the firmware update this is my second WAG54G2 router I did the firmware update on the old 1 and it failed so I RMAed it the only problems im having with it is slow transfer speeds over the wireless network and it disconnects from the net now and then. I also would like to what hardware should I use to get a 108mbps over my network because 54mbps is just too slow. I used windows 7 and mozilla to do my frimware upgrade and it failed.
View 3 Replies
View Related
May 23, 2011
Let's say, an antenna like that Should I open the modem and therein there could be a slot for it to be plugged in? Because on the back side of the modem none of the slots will suit such plug.
View 2 Replies
View Related
Mar 12, 2011
I connected to the internet using my WAG54G2 and PPPOE connection.sometimes the internet dissconnects and I have to click the connect button in the modem status manually I selected "Keep Alive - Redial Period" but it does not work !
My firmware version is V1.00.19
View 2 Replies
View Related
Nov 7, 2011
How can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?
View 1 Replies
View Related
Feb 11, 2011
I'm facing a strange problem here with my WAG54G2 gateway. I've got a very bad connection when the signal strength is 2 out of 5 or less. I tested the DL and UL speed via url...and gives me hardly 1 Mb/s even though I have 10Mb ADSL connection. With wired and wireless connection with 3 out of 5 or more I got 8.7 Mb DL from the mentioned website.
View 1 Replies
View Related
Oct 20, 2010
My Encapsulation router WAG54G2 switch RFC 2516 PPPoE to Bridged mode only everyday and all configuration that i made will reset and also Application & Gaming button error when i click.I'v reset to factory default and upgrade the firmwire to the latest one but it not work also I replace the device but nothing changed.The problem will solve if I cut the powir off and restarted agein.
View 3 Replies
View Related
May 27, 2011
Last year I was working with Vista laptop and pc , there were no wireless problems with the WAG54G2-EW. Now I have 2 laptops, working on windows 7. But they cannot go to wirless mode, only connected with a cable I can go to the internet. I have downloaded the last firmware.When I tried Windows help the conclusion is : your router cannot be configurated for Windows7
View 2 Replies
View Related
Dec 20, 2011
There is a Linksys WAG54G2 firmware v1.00.19. If you try to configure access to wi-fi on the list of MAC-address get the error "The MAC address can not be broadcast address" for the MAC address - 5c: XX: XX: XX: XX: XX, for mobile phone Sony Ericson Neo. Safety on the modem is turned off. Laptop computer and connect to Wi-Fi without any problems. Prompt a possible solution. Which parameters can be set?
View 3 Replies
View Related
May 2, 2011
My internet connection seems to drop a lot, I'm using a WAG54G2 modem connecting via a wired connection; and my ISP is Iprimus and I'm running off an Adsl2+ connection.The light on the modem that goes out when I lose connection is usually the internet although sometimes it is the DSL light, when my connection drops out I also seem to lose speed when I reconnect, which I was able to fix by pulling the power plug out and putting it back in but it no longer works as often.
The top speed I have measured via 9url]... has been 350 kb/s and the lowest has been 12 kb/s.My phone line also has a loud crackly sound which goes away when I unplug my modem from the line.I used to be able to unplug my phone line to keep the connection up but that no longer works.
This problem is not consistent as I will have days when it is bad (slow connection speed and constant connection dropping) and days when it is alright (decent connection speed and hardly or no connection dropping).I am also running a few filters for my phone, I've tried taking the filters out but that doesn't fix it, I've tried unplugging the phone which used to work as I mentioned before but no longer does.Before I bought this modem I can't remember what I was using but that had history with locking out the connection which by replacing the modem fixed my bad connection for a 5-7 months.
View 2 Replies
View Related
Jan 9, 2012
I have two LAN networks. Both using LINKSYS WAG54G2 Wireless + Gateway. I can create a VPN tunnel between the two networks to connect them. But since the data will be transferred over the internet, I want to know how safe it is. Is there anyway i can make it more secure?
View 3 Replies
View Related
Feb 26, 2011
when i enter 2 Access Restrictions & add put some data After a period of time Control Panel crashes
View 6 Replies
View Related
Nov 22, 2010
I've been using the WAG54G2 for some time now, recently I set up a range extender and had some issues so one thing I tried was to upgrade the firmware. It was very unclear on this website where to find it (specifically for the G2). I went here but there were 2 files, Annex A or B? [irl].... The instructions are also very unclear on this. But more frustratingly the zip file just contains an ".img" file - no ".bin" as the instructions say. So i tried the manual firmware upgrade using this file and shortly after the message "...whatever you do - do not close the browser or restart the router during the upgrade..." (or similar) the router crashed, so I had to restart it and the browser. Now I think I may have introduced an error as the once perfectly-performing router occasionally drops the internet connection for a few minutes. With my work I need 100% uptime.
View 3 Replies
View Related
Nov 11, 2010
When i download alot (around 400-700 kb/s) or upload ( around 100kb/s) the router stops responding, for every connection. LAN WAN WLAN, all stop responding... active connections though remain connected but visiting new sites/pages is not possible...
plugging out the power for 10 seconds and booting it up again..
View 9 Replies
View Related
Dec 26, 2012
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies
View Related
Feb 8, 2011
I have WAG54G2 wireless modem. It has been working perfectly until I formatted my desktop computer and reinstalled Windows XP. Now I want to reinstall my modem but is gives this error:"Error 322 New Router or Gateaway Not Detected"The old wireless configuration still works with my laptop, but I am afraid of losing my wireless connection so I did not reset the modem. Do I have to reset it?
View 1 Replies
View Related
Jul 31, 2012
I have a similar thread about this issue, the issue of this modem not support any kind of port forwarding actions... even disabling firewalls, using DMZ, port range forwarding the whole ip range , solves a thing...
it has upnp and port ranging features all over it but somehow it does not do it, and nobody cares excepty the ones that invested in it...
so if you are stuck with a router like me, dont bother wasting hours on it, and leave it to the people who are responsible for it.
View 2 Replies
View Related
Apr 28, 2011
I own a lynksis wag54g2 wifi router. I can establish wi-fi connection with my Android phone, Iphone 4, notebook, but after I disconnect the device from the router, I can't reconnect it again until I reboot the router. I tried some othe mobile devices with wi-fi support, the problem is the same. I tried set up different wireless security settings, tried to switch wireless mode to b, g, and mixed, installed new firmware 1.00.19, but the problem is not resolved.
View 1 Replies
View Related
Jun 28, 2012
I have a WAG54G2 working fine for more than 2 years now. It has the initial firmware version 1.00.10
Recently I mode it from my home to my store, where I have a already working CCTV setup. Initially the router did not work, but once the service provider removed the mac-id binding (with my previous ADSL2+ router) the WAG54G2 was connecting on DSL. However it never got a DNS value. Currently I am using it with a fixed DNS.
After a few days of working I noticed that my remote viewing for the CCTV was not working. On checking the router settings I saw that the router had defaulted to no settings at all. Changing it back to PPPoE did not work since the page would not render completely. Resetting to Factory settings also did not work. However simply switching off the router and restarting it worked. I let it go then. The same thing happened again within a day or two. Each time restarted the router seemed to solve the problem, however temporarily.
I have the SPI firewall enabled also I have application port forwarding set for HTML port 80 forwarding to say port 1234.
View 2 Replies
View Related
Sep 30, 2011
correct settings > Configuration of WAG54G2 on etisalat adsl fiber optic
View 1 Replies
View Related
Oct 21, 2010
Running Firmware v. 1.00.19 here, which I reckon is the most recent version.
My network consists of two Macbooks, an iMac and two iPhones. It utilizes WAP2 encryption and all devices are well within range, the environment being free of interferences from any other WiFi signals (this is a rural area).
My problem: Bonjour networking stops working after a few minutes or hours. When the problem appears, WIRED devices can see all other peers in the network (both wired and wireless), but WIRELESS devices cannot see any other peers whatsoever (wired or wireless).
I have heard that this could be because of a faulty implementation of uPNP by Linksys, and in particular a problem with multicast filtering (and unfortunately the modem/router's firmware does not provide any relevant settings). But I am not sure.
I purchased this thing with the express purpose to use it on a Mac-only network, and I am thoroughly disappointed to see that it does not work, especially since UPNP is supposed to be supported.
View 1 Replies
View Related
Nov 24, 2008
I just purchased a WAG54G2, setup was simple and easy. After being on for about 16 hours if I login to the device all the settings appear to have been reset to default, although the access point and wireless are still working. After another few hours the internet access stops and device appears to have been reset. No power spikes or reliability problems with power. Contacted Linksys support on three different occasions and they don't have any suggestions that work. Tried a "hard reset" but problem still occurs. No firmware upgrades are available for this device.
View 9 Replies
View Related
Jul 10, 2011
Basically sometimes I suffer from serious lag! I want to best setting to get the most out of my modem. What are the reccomended setting for this modem?
View 1 Replies
View Related
Jan 16, 2012
my router is connected to main router from my internet provider. When I use x3000 my download speed is half as fast as it should be (wifi and wired). When I connect to mian router directly (without x3000) both wifi and wired connection is at full speed.Is there any setting I should use to get full speed on x3000 - I have 24 Mbit/s?
View 1 Replies
View Related
Dec 22, 2011
I have a Linksys x2000 and have been using it successfully on DSL with a local ISP. I recently changed to Century Link and now I can't connect to the internet (Century Link). If I change the UserId and Password from my Century Link values back to my old ISP values, I can connect to my old ISP. Century Link tells me they have my account active with the X2000 and Century Link.
View 2 Replies
View Related
Dec 19, 2010
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?
View 5 Replies
View Related
