D-Link DIR-655 :: How To Erase All Settings When No Longer Using This Router
Feb 23, 2011Can I just plug the router into a 110 socket and then press the reset button to clear all stored information?
View 3 Replies
ADVERTISEMENT
D-Link DIR-615 :: Rev A No Longer Hold Settings?
Dec 8, 2012Had my DIR 615 rev A just fail one day spontaneously; managed to bring it back by reflashing from the emergency room, but now it will not hold setting through a power cycle, other than this it seems to be working well.
View 9 Replies View RelatedCan No Longer Access Any Of Router Settings
May 1, 2012My internet has been very sluggish so after reading the thread about Router security and neighbors who might be stealing my internet connection via WIFI, I decided to check what kind of security I had. Turns out I have WPA and no unknown devices were connected at that time. Would like to get an email whenever a NEW device logs in...if that is possible. But while I was in there "futzing around" I did something terribly wrong. I followed all of these steps. Then I noticed that the router speed section had me listed at 145mbps. I had recently changed cable companies to one that provided faster interenet. So I figured I would bump that up to 300 mbps. I can no longer access any of my router settings. What did I do, and how can I undo it?
View 4 Replies View RelatedDell :: Restored Inspiron N5010 To Factory Settings And No Longer Have Wireless
Jul 11, 2013I installed the drivers that came installed on the PC.
I looked at the settings and confirmed that they were correct per my internet provider.
Enernet works and I can hook up using cable. But the PC used to auto detect all wireless connections available. Now it detects nothing.
D-Link DIR-825 :: Router No Longer Connecting To Internet
Dec 21, 2011Background: This weekend, I lost my internet connection at home. I called my ISP and they sent someone over. The guy rewired the entire house (our ISP is also our tv cable provider), because he felt that our signal was probably weak due to the wiring. Long story short, after two hours of rewiring and fixing the cable outside out house (chewed through by a squirrel), he said the modem's signal was back to normal and left.
When I plugged the router; however, it refused to hold the internet connection for more than a few seconds. On the front panel, the planet-shaped light turned orange, then blue (for a few seconds) and then turned off entirely. I tried another few times and got the same result. At best, it stayed connected for a minute, until I rebooted my computer. The laptops in our house do read the presence of the router, so it's safe to assume that the problem lies with the router's capacity to receive the signal.
D-Link DCS-930L :: Router No Longer Sees Camera
Apr 11, 2011I have a wireless network in my home. I reliably get solid connections on our various devices such as the Wii (netflix streaming), a net book, a laptop and Wi-Fi connections on android phones. When I first set up the 930L I thought it was defective because I couldn't get a connection. Until I did it in the same room as the router okay, that worked. But I move 2 rooms over and I no longer connect.
Seriously, I can go a few rooms away and easily stream an HD movie via netflix to my net book. But if I set up the 930L at the exact same location it will not connect. If I move the camera within about 20 feet of the router with only maybe 1 wall between them, it will connect.
At this level of wireless power it is nearly worthless for me. Is my camera defective or are all of them this lower powered?I am running a dlink router, 300N, WPA security. Like I said, I can connect if I'm literally 10 feet away. But any significant distance or anything more than a single wall in between and the router no longer sees the camera. And all other wireless devices have strong, reliable connections all through my house.
Cisco :: Router 8803G - Erase Admin User / Change Password
Jan 15, 2013i have a Cisco Router 8803G and i would like following commands to be run by telnet:
1) erase an admin user
2) change the password of an admin user
D-Link DIR-655 :: Can't Save Any Router Settings
Jul 20, 2011why I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page.
View 3 Replies View RelatedTp-link Wireless Router Security Settings?
Sep 12, 2012I forgot my router security code number but still working i want to need make new secure
View 1 Replies View RelatedTP-Link 3G/3.75G Router :: TL-MR3220 Manual APN Settings
Mar 14, 2013Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
D-Link DIR-655 :: Local Domain Name Settings On Router
Nov 21, 2012I have the DIR-655 (H/w Ver B1, F/W Ver 2.05NA) set up as router on my network (TWC/RR - modem is Motorola SURFBoard 6121 - modem only, no router or other services provided). I have configured the router sufficiently to allow all computers on the local network to access the Internet, and have configured the DHCP server on the router to provide IP addresses to the local network. I have configured the router to provide the DNS addresses for my local DNS resolvers (so that I can provide DNS resolution for an "internal" domain). Configuration specifics available on request, but everything mentioned so far is working satisfactorily, at least so far.
So, my question: The "Local Domain Name" setting on the router, as indicated in the documentation, provides a connection-specific domain name when DHCP supplies an IP address to the local system. This setting, however, is overridden if the ISP provides a domain name when it assigns an IP to the WAN connection. I have verified by experiment that this is true (no matter what I put in the Local Domain Name field - whether a valid domain, or blank - the local machines receive the domain name supplied by the ISP.I wish to modify this behavior. I wish to have the router provide the domain name specified in the Local Domain Name field *regardless* of what the ISP provides.
D-Link DIR-655 :: Settings To Limit Bandwidth From Router?
Jun 11, 2011I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
D-Link DIR-655 :: Hookup A Usb Cable To Get Router Settings
Apr 10, 2011I have been trying for days to get a HP Photosmart Plus B209a wireless printer to work with my D-Link DIR-655.Going through the HP setup cd for I get to the section where it wants to hookup a usb cable to get router settings and finds my network and then I put in the password. Then after looking for a bit it says it can't find the printer.Looking at the wireless status page it says the ip address is 0.0.0.0.Reading on HP's website it says that you must have the router set to broadcast the SSID, I believe mine is set to hide. How would I go about changing it to broadcast AND would it mess up all my other settings changing it to Broadcast, meaning will I have to reconfigure the other computers again? Do I use the set up wizard to edit things or is that for first time set up ?
View 5 Replies View RelatedTP Link Td W8951nd - Connecting To Router / Configuring Settings?
Feb 3, 2013I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
D-Link DIR-655 :: None Of Port Forwarding Settings Are Working At All On Router
Nov 30, 2012None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies View RelatedD-Link DIR-655 :: Cannot Access Router Or Reset Factory Settings
Jul 22, 2010My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies View RelatedD-Link Wireless Router Not Working After Changing Speed / Duplex Settings?
May 24, 2012I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies View RelatedTP-Link 300Mbps Wireless :: TL-WR841ND - Failed To Verify Router Settings
Feb 2, 2013Region : United Kingdom
Model : TL-WR841ND
Hardware Version : Not Clear
Firmware Version : 7.1
ISP :
failed to verify router settings
What's wrong with my router?
TP-Link Dual-Band Wireless :: TL-WD2543ND Router Settings For Smarbro Wimax
Dec 4, 2012Region : Philippines
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : Smartbro WiMax
I'm using the router TL-WR2543ND, I have pesonally configured the router myself, I'm no that good in computer but I managed to do so. I never had difficulty doing it. I have decided to switch to Smartbro Wimax and tried to connect it to my tp-link router but no luck. I browsed the net for possible instructions to do it but just frustrates me. I have changed the IP address of the router to avoid conflict, cloned the MAC address, still unable to connect the router.
Option To Erase History?
Jun 29, 2011I have a lap top that someone else uses, is there anyway I can set some setting that erasing the history is not an opinion?
View 1 Replies View RelatedD-Link DIR-655 :: Can No Longer Access Internet
Jan 28, 2011My DIR-655 has been working flawlessly for several months since I bought it. It is connected to Road Runner High Speed Internet from Time Warner. This morning it will not access the Internet. It shows a wireless connection, and I can connect to it via direct wired connection, but no Internet. A direct connection to the Time Warner Cable Modem connects to the Internet just fine. Cycled power on all units, & Time Warner reset the modem. Nothing has fixed the Router.
View 14 Replies View RelatedTP-Link Dual-Band Wireless :: TL-WDR3600 - Binding Settings Can't Apply Automatically After Router Reboot
Mar 17, 2013Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.
D-Link / Netgear - Network Is No Longer Showing
Jun 16, 2012The other day while I was browsing the internet all of a sudden my internet stopped working. I look down below and try to connect to the network again but it no longer shows my network anymore. I went into the room of my router and it looked fine. All lights were lit up like they should be. I turned on my Laptop to see if it was just a problem with my desktop but it's still not showing my network either.
I have restarted my router and reset it numerous times and it has still yet to show my network. It only seems to work if I connect it to my Laptop with an Ethernet cord. I have two different routers (Both Linksys) and they both do not work.I also have two different wireless adapters (D-Link & Netgear) and they both do not work
D-Link DIR-615 :: Wireless Controller No Longer Works
Jan 5, 2012Well I was trying to get my D-Link DIR-615 router too run DDWRT so I could use it as a wireless reciever.But things have gone wrong, the wireless controller no longer works. and I'm trying to restore the original factory firmware.(this is a spare router we had sitting around it's not an important asset) it boots up fine with DDWRT firmware the wire functions still work, but I needed the wireless functions.I just can't get the original firmware back.
View 1 Replies View RelatedCisco Firewall :: Pix 515 - To Erase Flash Memory
May 12, 2011Need this file to erase my flash memory?
View 2 Replies View RelatedCisco :: Catalyst Won't Booting Up After Erase Startup-config?
May 15, 2012i have an urgent situation that my catakyst C3550 wont booting up after i reset the startup-configuration using "erase startup-config" command. now everytime i connect to the catalyst it show me "switch: " not "switch>", i have try using "boot" command in the "switch: " session but it said"Loading ""...: permission denied"error Loading ""
View 2 Replies View RelatedCisco Firewall :: ASA 5505 ROMmon After Erase Flash?
Oct 19, 2012I was trying to erase some bad test configs on my 5505 with a write erase, but all VLAN and Ethernet configs remained. I hastily decided to do an erase flash. No I'm stuck at a ROMMON prompt with no image found to boot I'm hoping I don't have to TFTP a factory image. How do I find the images on disk0 and copy them?
View 16 Replies View RelatedCisco Firewall :: Getting PIX525 Flash Erase Tools?
May 4, 2011I have two pix525 firewalls cann't boot up normaly and i find [[URL] no longer provides the falsh erase tool ,erasedisk.bin,download.
View 4 Replies View RelatedD-Link D-ViewCam :: DCS-2132L No Longer Accessible - Port 80 Not Working
Mar 17, 2013Taking another look at Dview cam today after not touching it for 3 months after initial install.The dcs-2132L can't connect.I can to the 2132L directly... I changed the port as a test.. Port 80 wasn't working originally.
[url]....
TP-Link ADSL2+ Wireless :: TD-W8951ND V5 No Longer Have Mac Spoofing Option
Feb 20, 2013Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
D-Link D-ViewCam :: DCS-5300 And DCS-6620 No Longer Connected With Software
Dec 24, 2009I originally began using my D-Link cameras, two DCS-5300s and a single DCS-6620, with the IP Surveillance software. I see that the software is no longer recommended and may no longer be available. Any explanation for the move to the DView Cam software ? If I were to convert over to DView Cam from IP Surveillance will I lose any functionality or features. Will there be any functionality or features gained ?
View 6 Replies View RelatedCisco Firewall :: PIX 535 - Erase Flash Files From Monitor Mode?
Jun 1, 2010I have pix 535 and wanted to erase the flash files (faulty) which already utilised 13 mb .so i cant upload new ios so i want erasedisk.bin ,i also have CCO account.
View 6 Replies View RelatedCisco Firewall :: PIX 515e - Cannot Write / Erase Or Configure Factory Default
Jul 3, 2011I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it.
I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.