Can No Longer Access Any Of Router Settings

May 1, 2012

My internet has been very sluggish so after reading the thread about Router security and neighbors who might be stealing my internet connection via WIFI, I decided to check what kind of security I had. Turns out I have WPA and no unknown devices were connected at that time. Would like to get an email whenever a NEW device logs in...if that is possible. But while I was in there "futzing around" I did something terribly wrong. I followed all of these steps. Then I noticed that the router speed section had me listed at 145mbps. I had recently changed cable companies to one that provided faster interenet. So I figured I would bump that up to 300 mbps. I can no longer access any of my router settings. What did I do, and how can I undo it?

View 4 Replies


ADVERTISEMENT

D-Link DIR-655 :: How To Erase All Settings When No Longer Using This Router

Feb 23, 2011

Can I just plug the router into a 110 socket and then press the reset button to clear all stored information?

View 3 Replies View Related

D-Link DIR-615 :: Rev A No Longer Hold Settings?

Dec 8, 2012

Had my DIR 615 rev A just fail one day spontaneously; managed to bring it back by reflashing from the emergency room, but now it will not hold setting through a power cycle, other than this it seems to be working well.

View 9 Replies View Related

Dell :: Restored Inspiron N5010 To Factory Settings And No Longer Have Wireless

Jul 11, 2013

I installed the drivers that came installed on the PC.

I looked at the settings and confirmed that they were correct per my internet provider.

Enernet works and I can hook up using cable.  But the PC used to auto detect all wireless connections available. Now it detects nothing.

View 3 Replies View Related

Linksys Wireless Router :: Befw11s4 Can No Longer Access Router

Nov 25, 2011

I have a BEFW11S4 router when to put in password for the router and must have had a typo as I can no longer access router.Tried the factory reset on the rear of unit to no avail. Is their any way to get access as I have the main computer wire to the router. I need to get into the unit to move the channel number.

View 2 Replies View Related

Linksys Wireless Router :: EA6500 No Longer Access To GUI In Bridge Mode

Dec 15, 2012

After updating the firmware of th EA6500 to Ver.1.1.28.146072 I have no longer access to the GUI options of Speed Test, Guest Access, Parental Controls, Media Prioritization and USB Storage. I have reset the router to factory default settings and still none of the items are showing on the web page the only options available are:Connectivity,Troubleshooting.Wireless.

View 5 Replies View Related

Linksys Wireless Router :: E4200 Users Can No Longer Access Mapped Drives

Dec 14, 2011

I have a file server running windows 2003 and five computers (1 windows 7, 4 windows xp-sp3).There are two shares on the server.When the router is setup with wpa2, three of the windows xp machines will have problems with mapped drives. Directly after the drives are mapped, everything works, but 10 or so hours later, users can no longer access these mapped drives and there is no way to reconnect them it seems.The other two machines (windows 7 and one windows xp machine) have no problems whatsoever.
 
The only thing that the three computers have in common is that they are also sharing a printer (an hp j4680) attached to one windows xp machine (not the server).If I set everything to wpa, everything works fine, but of course my wireless network speeds drop to 56mbps.

View 4 Replies View Related

Can't Access Router Settings

May 28, 2012

So I used an Url to acess my router but then, it asked for a username and password. I know I havent messed with it because this is the first time I seen this. I tried leaving the username blank and typing in "admin" for password but nothing worked

View 5 Replies View Related

BT Hub - Can't Access Router Settings?

Jan 14, 2012

I used to have Avanti Satellite broadband but then upgraded to new BET technology with BT which allowed people living very far from their exchange to get up to 2mb phone line broadband. With Avanti, I could access my Buffalo routers settings by just typing in the routers ip.But, now with the new BT Hub we got, whenever I type in ipconfig to cmd, the gateway address is the address to access the settings of the hub. I tried the old bufallo ip but it is not working. I think this is because the hub is a router aswell. Is there anyway I can access the routers settings?

View 13 Replies View Related

Can't Access Belkin Router Settings

Sep 25, 2012

I just say that I'm not brilliant with pcs but I'm able to follow instructions if they are in the consistency of baby food! XD..Well basically I can't access my wireless modem router's settings (2 in 1 device I believe). I managed it once but haven't been able to do it again. I've tried the following:

-Reset router many times.
-Turn it on and off many times.
-reset router while ethernet cable is connected and without.
-ipconfig/release and renew

notthing works!!! I noticed the ip address changed from the default one of 192.168.2.1 to a completely different one...95.175.138.When I turned on my laptop today after being off overnight (and the router) somehow I did managed to get on the settings page again using 192.168.2.1 but didn't last for long. While I did this there was a warning icon next to the wifi icon, but then when the warning sign went off that's when the router's setting page stoped working again.I need to get to the router setting because currently is set to go off when i turn off my laptop which is a bit pointless and change a password.

View 14 Replies View Related

Cannot Access Wireless Router Settings?

Mar 5, 2013

I can't get into my router's settings, when I try, chrome says the page is not available. I checked, the IP is correct, and I can't access it on multiple computersI recently changed a few setting. (I set it to max 300 mbs per second from 54, and one other thing that I don't recall) The problem occurs on three different computers(A mac and two PCs) I've restarted my router several times to no avail. What should I do?

View 1 Replies View Related

Can't Access Router Settings Page

May 13, 2012

I am having a problem accessing my router settings page. everything was working fine and then all of a sudden my desktop couldn't get internet but all the laptops could so I tried everything power cycling the everything changing the Ethernet cable and I got nothing. So then I hard reset my router and erased all the settings and now it works so I have internet just fine and right away after I hard reset I could access my router settings page and input all of my settings like DNS servers and port forwarding and changing my SSID etc. but now every time I try and go to it it just won't I don't even get the login prompt nothing. So why I can't access this page. Here is a copy of my ipconfig /all. Also when I ping 192.168.0.1 I have no packet loss.

Edit:I have gotten it to work in IE I have to go to HTTPS://192.168.0.1 and then click go to site anyways after it gives me a warning about the certificate being invalid and I have to allow it or whatever otherwise it won't bring up the login prompt. Also the same thing is happening for FF so I need to go to https://192.168.0.1 and click I understand the risks and add exception for it to work.

Windows IP Configuration

Host Name . . . . . . . . . . . . : Andrew-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

[code]....

View 2 Replies View Related

Can't Access Hotel Router Settings

Mar 3, 2013

me and my co-worker bought an xbox and we can connect online but we have no open NAT. I asked the manager if I could take a look and set it, he said that'd be fine but there's one problem; it's seperated by sheet rock in the cieling. I asked if I could take a look on the lobby PC and try to access it there and he said it'd be fine, he understands that I'm not tampering with anything other than just turning the NAT on, he's been trying to access it himself. I went to the cmd prompt and did ipconfig /all, got the default gateway ip and typed it in, but there are no settings just a display from air2data.I can't reset the router.

View 1 Replies View Related

Can't Access Router Settings - Blank Screen?

Jul 29, 2012

I am trying to change the name of my wireless network but when I go to the 192.168.1.1 and type in my password, it just goes to a blank screen. I've accessed my router a lot of times before this way. It is a lisksys router.

View 1 Replies View Related

Actiontec GT724WGR - Can't Access Router Settings

Jun 26, 2011

I bought an Actiontec GT724WGR. I downloaded the latest firmware and went to install it. When it finished, I got the confirmation box and it gave me the click okay to restart option. I clicked okay, and when the router power cycled, the Power light stayed amber. I can't manually reset the setting back to default with the reset button. I can't access the router settings.

View 1 Replies View Related

Wrt54g Linksys - Cannot Access Router Settings

Jan 1, 2012

I have a wrt54g Linksys router, and recently whenever I type 192.168.1.1 into the internet in order to access the settings/homepage, I get " internet cannot display this webpage"

View 2 Replies View Related

Linksys Wireless Router :: E1000 - Can't Access Router Settings After Changing To Static IP

Jun 26, 2012

I installed an IP camera, and had to change my E1000 router settings to a static IP address.  Now I can't access the router settings.  192.168.1.1 is still the default gateway, but it won't open in any browser.
 
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place.  I'm not very good at this stuff, and it's a small miracle that I did it once.  

View 4 Replies View Related

Linksys Wireless Router :: Wrt54gs V7.2 - Can't Access Settings

Jul 8, 2011

I changed the router's IP to 192.168.2.1 due to the same situation as this [URL] linksys and now I can't access my settings I have tried the both pips and nothing and I can't seem to get my linksys wrt54gs v7.2 to let two computers be on the internet at the same time both can be on the network but on one on the internet

View 6 Replies View Related

D-Link DIR-655 :: Cannot Access Router Or Reset Factory Settings

Jul 22, 2010

My computer is an XPS 360 with alot of upgrades.  After looking at the specs of D-links routers I thought I give it a try.  Hooked up, works like a dream.  Couple months later my computer was saying I have "limited connectivity."  All of the other computers have full access and works great.  I tried going to my routers home page, but all I get  is "The server at 192.168.0.1 is taking too long to respond."  Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine.  I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end.  I called Dell for support, said my warranty went out and they cant do a thing.

View 14 Replies View Related

Linksys Wireless Router :: Way To Get Software To Access E2500 Settings

Oct 13, 2012

I just purchased an E2500 wireless router. I put the Cisco Connect setup disc in and it could not find my router. With excellent Tech Support, I got it to work. I still do not have any Cisco Connect software on my PC to set passwords or preferences. If I try to run the disc again, it gives me a system critical error and shuts down my computer. How can I get software to access my router settings?

View 1 Replies View Related

Cisco Switches :: 2801 Router - Access Settings Of SF300-24p?

Jul 6, 2012

I was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is  a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors?

View 13 Replies View Related

Routers / Switches :: Unable To Access Virgin Media Router Settings

Jan 7, 2013

to enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.

View 2 Replies View Related

Protocols / Routing :: Buffalo WHR-G125 - Can't Access Router Settings (404 Error)

Aug 31, 2011

I have a Buffalo WHR-G125 router which was given to me for free by my ISP for being a loyal client. At home I have a computer, a laptop and a netbook. The router is connected to the computer and I have no trouble accessing the Internet on all three of these devices. I can open pages, download etc.

However: However if I decide to host a server on some game, my friends cannot connect. After doing some research, I found out that certain ports are "closed" (whatever that means) and I need to open them in order for everything to start working again."

Anyway, I checked the infamous site "portforward.com" for instructions on how to open these ports. It was all fine and dandy, until the point where they stated I need to access my router settings page ("default gateway" or whatever, you'll have to excuse my ignorance). I entered "ipconfig" in cmd and it turns out my default gateway is 192.168.1.1. So I entered this in the URL bar of my browser and got a nasty surprise:

"404 Not Found The requested URL was not found"

I am truly stumped. The address is not accessible on neither the computer, nor the laptop or the netbook. I tried some automatic port forwarding software, but it didn't seem to do anything for me.

The only reason for this I can think of is that my ISP is probably blocking the router settings page for some reason (and how unfortunate, I can't even complain, because it's free, after all).

I tried asking on the official Buffalo forums and even tried asking for support and got pretty much the same message: "Try resetting. However, if it's flashed, you can't do anything.".

Not exactly sure what to do right now. My worries:

1.) I'm not even exactly sure how to reset the darn router

2.) I'm scared that reseting won't do a thing and even if it does, I'm not sure I'll be able to reconfigure the entire thing by myself and the worst case scenario, not having internet at all.

Is there any way to access the friggin router settings page?

View 5 Replies View Related

Linksys Wireless Router :: Wrt120n Unable To Access Settings Page

Jan 6, 2012

Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".

View 2 Replies View Related

Linksys Wireless Router :: Access EA6500 Settings To Setup Security?

Dec 31, 2012

just set up my EA6500 in bridge mode, i have the Ethernet cable plugged into the EA6500's yellow WAN port, is that correct, Cisco Article ID: 24583 is not that clear, Cannot also seem to access the EA6500's settings to setup security?

View 2 Replies View Related

Linksys Wireless Router :: WRT610N No Access To Edit Any Settings On The QOS Page

Mar 11, 2012

I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);

Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.

View 1 Replies View Related

Can No Longer Access Internet From Desktop

Oct 10, 2012

Since sometime on 10/7/12, I can no longer access the internet from my desktop.I'm connected via wired Ethernet but have also tried connecting via a USB WiFi Modem.Network and Sharing Center shows "Unidentified Network No network Access".All other machines on my home network have internet access (one other desktop as well as multiple WiFi clients).I've tried pinging the router (192.168.1.1) .. request times out.I've tried reset TCPIP and Winsock Stacks, Disabling / Reenabling the NIC with no effect.In troubleshooting, I've found a registry entry which seems to be different from that in my working desktop and which I cannot change.It's HKLMSYSTEMCurrentControlSetservicesTcpipParameters. [code]

View 11 Replies View Related

D-Link DIR-655 :: Can No Longer Access Internet

Jan 28, 2011

My DIR-655 has been working flawlessly for several months since I bought it. It is connected to Road Runner High Speed Internet from Time Warner. This morning it will not access the Internet. It shows a wireless connection, and I can connect to it via direct wired connection, but no Internet. A direct connection to the Time Warner Cable Modem connects to the Internet just fine. Cycled power on all units, & Time Warner reset the modem. Nothing has fixed the Router.

View 14 Replies View Related

Vizio TV No Longer Finds Wireless Access Points?

Feb 19, 2012

my Vizio TV (VF552XVT) can no longer find any wireless access points even after inputting SSID or IP information. Other wireless devices (my phone) are able to connect wirelessly. Everything was working fine until a power outage about 3 days ago.

View 2 Replies View Related

Devices And Printers No Longer Shows Wireless Access Points

Jan 26, 2012

Had the following network (fully functional) for last 3 years: Modem (netopia dsl 192.168.1.254) router (linksys wrt54gs 192.168.1.1) WAP1 (linksys wrt54g2 192.168.1.250) and WAP2 (Linksys wrt54g2).I was always able to click on Devices and Printers in Win 7 and would see the equipment displayed.I could also access the router and wireless access points by typing their address in my browser. The modem failed after 5 years.I purchase a new Netgear N300 ADSL2+Modem Router (DGN2200)and replaced the failed modem and attached router.I made no changes to either WAP's.Everything works just fine (after about 30 minutes on phone with Netgear Tech to configure), but now none of the equipment displays in Devices and Printers. Also, I cannot connect to either WAP by typing their address in browser.I can see the Netgear device when I click on "network" in file manager.It displays a model number and is labeled a "gateway".

I'm just curious as to why I am no longer able to "see" or access the devices. Looks like I would have to actually pull the WAP's and connect to them directly if I needed to change their configurations.

View 1 Replies View Related

Cisco WAN :: WRVS4400N - Can No Longer Access Internet Or Login On The Network

Oct 17, 2011

I recently bought a new Cisco WRVS4400N router for our network which has 19 computers connected to a 24 port switch.  We are currently using a D-Link router and are upgrading to the Cisco router.  The problem I am having is as soon as I connect one of our servers or the 24 port switch to the Cisco router I can no longer access the internet or login on the network, I also cannot access the routers setup from either server.  If I connect the router to just a stand alone computer I can access the setup and change things but as soon as I connect the server or 24 port switch everything dies (all lights are still green on the router though so everything is connected).

View 1 Replies View Related

Cisco Wireless :: 4402 - Guest Access No Longer Working

Aug 10, 2011

There is one guest interface, one guest WLAN. The WLAN is set with a DHCP override address of the guest interface. But it no longer allows this as I found out. Anyway, I can get the client to now receive an address from the internal pool on the WLC, but it will not route to the authentication page. I noticed that the WLC excludes the clients attempting to connect on the guest WLAN due to failed 802.1x authentication! the WLC never even gave me the chance to authenticate using an account created either through the lobby ambassador or creating one directly on the controller.

View 3 Replies View Related

Dell :: Inspiron 1721 Laptop Can No Longer Access Internet

Dec 18, 2011

I have an Inspiron 1721 laptop and can no longer acces the internet unless I attach the ethernet cable from my wireless modem.  In other words, I can no longer access the wireless internet from my laptop.  I have talked with my internet service provider and the say the problem is the settings with the laptop itself because I can access the internet from my tablet computer.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved