Had my DIR 615 rev A just fail one day spontaneously; managed to bring it back by reflashing from the emergency room, but now it will not hold setting through a power cycle, other than this it seems to be working well.
View 9 RepliesCan I just plug the router into a 110 socket and then press the reset button to clear all stored information?
View 3 Replies View RelatedMy internet has been very sluggish so after reading the thread about Router security and neighbors who might be stealing my internet connection via WIFI, I decided to check what kind of security I had. Turns out I have WPA and no unknown devices were connected at that time. Would like to get an email whenever a NEW device logs in...if that is possible. But while I was in there "futzing around" I did something terribly wrong. I followed all of these steps. Then I noticed that the router speed section had me listed at 145mbps. I had recently changed cable companies to one that provided faster interenet. So I figured I would bump that up to 300 mbps. I can no longer access any of my router settings. What did I do, and how can I undo it?
View 4 Replies View Relatedone last try before boxing up my new DIR-655 and taking it back to Microcenter. I've opened a case via email and got the standard response, below.I have a Dlink DP-300U print server that works fine with my 'old' Belkin router, a F5D-7230-4 wireless unit. Nothing wrong with the Belkin, I'm just getting some service drops from my lousy AT&T ifitl 1.5mbps ISP and thought a new router might work. I actually read the manual (!!) before installing the DIR-655 and even followed it. The print server just isn't visible on the network. Everything else is, though. The 'suggestions' from Dlink tech support below are very useful. If I could 'see' the print server to verify its IP address, we wouldn't be having this conversation. I've rebooted everything, several times and even reinstalled my old Belkin router (which always sees the print server.) And Dlink, no...I'm not interested in paying you $32.95 for up to a half hour to maybe fix a problem caused by your new device. And dropping my call after almost 15 minutes on hold is not cool, either. With reference to the issue you are facing, we suggest you to kindly ensure that the IP address assigned to DP-300U print server is in the same network range as that of your DIR-655.
NOTE: The default IP address of DIR-655 is 192.168.0.1 Once it is done, try to ping the IP address of DP-300U using any of the wired / wireless client connected to DIR-655.note the DP-300U is not currently supported in North America. D-Link offers a premium fee based support line that will be able to support any issues you have with this product.
I installed the drivers that came installed on the PC.
I looked at the settings and confirmed that they were correct per my internet provider.
Enernet works and I can hook up using cable. But the PC used to auto detect all wireless connections available. Now it detects nothing.
My DIR-655 has been working flawlessly for several months since I bought it. It is connected to Road Runner High Speed Internet from Time Warner. This morning it will not access the Internet. It shows a wireless connection, and I can connect to it via direct wired connection, but no Internet. A direct connection to the Time Warner Cable Modem connects to the Internet just fine. Cycled power on all units, & Time Warner reset the modem. Nothing has fixed the Router.
View 14 Replies View RelatedThe other day while I was browsing the internet all of a sudden my internet stopped working. I look down below and try to connect to the network again but it no longer shows my network anymore. I went into the room of my router and it looked fine. All lights were lit up like they should be. I turned on my Laptop to see if it was just a problem with my desktop but it's still not showing my network either.
I have restarted my router and reset it numerous times and it has still yet to show my network. It only seems to work if I connect it to my Laptop with an Ethernet cord. I have two different routers (Both Linksys) and they both do not work.I also have two different wireless adapters (D-Link & Netgear) and they both do not work
Background: This weekend, I lost my internet connection at home. I called my ISP and they sent someone over. The guy rewired the entire house (our ISP is also our tv cable provider), because he felt that our signal was probably weak due to the wiring. Long story short, after two hours of rewiring and fixing the cable outside out house (chewed through by a squirrel), he said the modem's signal was back to normal and left.
When I plugged the router; however, it refused to hold the internet connection for more than a few seconds. On the front panel, the planet-shaped light turned orange, then blue (for a few seconds) and then turned off entirely. I tried another few times and got the same result. At best, it stayed connected for a minute, until I rebooted my computer. The laptops in our house do read the presence of the router, so it's safe to assume that the problem lies with the router's capacity to receive the signal.
Well I was trying to get my D-Link DIR-615 router too run DDWRT so I could use it as a wireless reciever.But things have gone wrong, the wireless controller no longer works. and I'm trying to restore the original factory firmware.(this is a spare router we had sitting around it's not an important asset) it boots up fine with DDWRT firmware the wire functions still work, but I needed the wireless functions.I just can't get the original firmware back.
View 1 Replies View RelatedI have a wireless network in my home. I reliably get solid connections on our various devices such as the Wii (netflix streaming), a net book, a laptop and Wi-Fi connections on android phones. When I first set up the 930L I thought it was defective because I couldn't get a connection. Until I did it in the same room as the router okay, that worked. But I move 2 rooms over and I no longer connect.
Seriously, I can go a few rooms away and easily stream an HD movie via netflix to my net book. But if I set up the 930L at the exact same location it will not connect. If I move the camera within about 20 feet of the router with only maybe 1 wall between them, it will connect.
At this level of wireless power it is nearly worthless for me. Is my camera defective or are all of them this lower powered?I am running a dlink router, 300N, WPA security. Like I said, I can connect if I'm literally 10 feet away. But any significant distance or anything more than a single wall in between and the router no longer sees the camera. And all other wireless devices have strong, reliable connections all through my house.
Taking another look at Dview cam today after not touching it for 3 months after initial install.The dcs-2132L can't connect.I can to the 2132L directly... I changed the port as a test.. Port 80 wasn't working originally.
[url]....
Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
I originally began using my D-Link cameras, two DCS-5300s and a single DCS-6620, with the IP Surveillance software. I see that the software is no longer recommended and may no longer be available. Any explanation for the move to the DView Cam software ? If I were to convert over to DView Cam from IP Surveillance will I lose any functionality or features. Will there be any functionality or features gained ?
View 6 Replies View RelatedWhen I am viewing live recorded video through d-viewcam I can hear the audio. I currently have 2 camera recording 24/7. When I go to playback to play a certain clip, there is no sound at all. When I save a clip and click export audio, still no sound.
View 4 Replies View RelatedRegion : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
I'm running Windows 7 Home Premium, and using a ASUS USB-N13 Adapter to connect to my ASUS RT-N16 Router. I am able to connect to the network with no problems, however every 10-15 minutes I will be disconnected. I am almost positive the issue is with this computer or the adapter, because I have no wireless connectivity problems with my xbox.After being disconnected, there are 2 ways that I get the connection back. I either:1. Right click the windows wireless network icon (bottom right) and click troubleshoot problems. This seems to turn the adapter on and off during the automated troubleshooting and is then usually able to connect.2. In the ASUS software, I click "IP Renew" and this can sometimes fix the problem.Sometimes I am able to stay connected for hours, while other times it disconnects every few minutes. I have no idea what the problem is, and I know my way around computers pretty well but I am not well versed in networking.
View 1 Replies View RelatedWe have a non-cisco device peering with Cisco 6500 for bgp. The routing table is fully populated and connection is good.But after some time we see bgp hold timer error on the non-cisco device. This device by default has a hold timer of 90 seconds which is different from default cisco hold timer. Will this cause any disruptions to the network? If we change the hold timer on one device to match on both sides, will it reset the bgp session?
View 10 Replies View RelatedThe computer has a strange habit of dropping my internet connection after it's been turned on for a while. I've already checked to make sure that the setting which allows windows to turn the wireless adapter off to save power is disabled, and I've set my laptop up to use a static IP address which no other device should be using. I'm connecting via wifi.The only way I know to fix the problem is to restart the computer whenever the problem presents itself.I have a motorola surfboard modem and a linksys e1000 router.The computer always says that I am connected and that I have full signal, but it displays an exclamation point over the internet icon saying 'no network access'
View 4 Replies View RelatedUsing a wireless connection, my PS3 struggles to hold the connection. It either times out trying to sign on to PSN or EA sports, or connects only to lose the connection shortly thereafter. My router is the AC1000 and I'm wondering if there is a specific setting that is required in the setup that I'm not aware of. My connections to all other devices are solid.
View 2 Replies View RelatedI have a win 7 netbook that I recently got and for some reason it suddenly cannot keep a connection to the internet. It used to keep a connection before but now I keep getting the error the default gateway is not available about every ten minutes while connected which of course is very frustrating.
I've tried updating all associated drivers but apparently that hasn't changed anything. I've tried restarting the computer and tried different connections. I know its nothing to do with the internet connection I'm trying to connect to as other devices are able to keep a connection with no issue.
I am trying to figure out how this works. I have an ISP device that connects to my 1841. ISP and fa0/0 hold the /30 WAN addresses. Fa0/1 hold one of the public IPs, lets say 1.1.1.1/29. Then the outside interface of the ASA holds 1.1.1.2/29. Now I have two routes in the 1841, one for default route going back to the ISP device, and a route for the 1.1.1.0/29 network going to the ASA.Now I have 4 more publics I can use 1.1.1.3 - 6. I do not want to assign these IPs to the servers, but yet just NAT them. I know this is possible, but cant figureI took an internal host and did a one to one static NAT from private to public. Packet tracer says my NAT rules are ok. Allowed all IP traffic for testing and still can't ping the server.
View 3 Replies View RelatedHow can I hold the public IP on my cisco client VPN NAT session so nobody else can use it? I have a cisco asas 5510 inside is 172.10.20.86 public 166.245.192.90
View 1 Replies View RelatedHow can I hold the public IP on my cisco client VPN NAT session so nobody else can use it? I have a cisco asas 5510 inside is 172.10.20.86 public 166.245.192.90
Did I need to call my ISP?
I got a new DIR-825 router and when I try to change settings such as the date and time or try to apply web filters my changes won't save.
View 2 Replies View RelatedI have a DIR-655 that was working for the longest time, then out of the blue it just decided to stop getting a connection to the internet. I can connect to the router, but for some reason, it will not get any network settings. When I check the status/device info/WAN section, it just shows:
[code]....
why I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page. This just started happening.
View 3 Replies View RelatedMy wireless on my computer won't hold a connection for any longer than 30 minutes. I've checked the drivers, the wireless router, and scanned for viruses (several times) but nothing seems to work. In the last three months, I think I only had one occasion where the connection remained stable for longer than an hour. It doesn't matter what router I use or where I am. It has to be my computer.
I have a Compaq Presario CQ57 and I have had it for about 6 months.
My E3200 is having issues with keeping the speed up on wireless G. I'm about 20 feet away from the E3200 and there is 1 6in wall between me and the E3200. My connection will not hold 54Mbps, its constantly dropping to 36Mbps, even down to 5.5Mbps faily often. Around 30 feet away there i will lose internet connection yet my laptop says excellent connection to wireless.
View 2 Replies View RelatedI have configured a cisco UC520 with inbound called coming in on FXO port 0 and have configured it as a co-line. I have 4 phones set up on the system including the wireless 7921 phone, the problem is that if i answer the call on the 7921 it does not give me the option to hold or transfer the call however the other phones do (7931).
View 1 Replies View RelatedBlocking Ports don´t send BPDUs, but they can receive them from designated ports.Blocking ports, can it hold BPDUs?
I think that Blocking Ports only receive, analyse and then discard the BPDU.But, what happen if the blocking port receive a better o worse BPDU? in this case, must be the bpdu stored?
I'm trying to change some network settings, but the router is unresponsive when I try to connect to its ip address. If I reset the router it opens a 20 second window where I can log in, but then goes unresponsive. I have encountered this on my main pc connected wireless, and duplicated the results when wired in with my netbook.
View 1 Replies View Relatedwhy I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page.
View 3 Replies View RelatedI'm trying to set up opendns on my DIR-825, firmware v2.05. Under the Setup/Network Settings I set the primary and secondary DNS Server IPs to the ones from [URL] and save the settings and they don't stick.I have also unchecked the "Enable DNS Relay". Well, tried it on and off and neither pad a difference.
View 3 Replies View Related