i'm using 2960 cisco switch and every department has a switch same model, i have noticed that every 10 to 15 minutes my network is disconnected for atleast 10 seconds and all client conneted to the server was disconnected also.
View 26 Replies
In my customer having 3750 switch and they have simply assign IP address for vlan and enable telnet in switch and other things are same as default switch.In this switch they have connected 8 cisco layer 2 switches(6 managed and 2 unmanged switch) and approximately 5 servers connected in this switch.In a particular interval,users accessing File server are connected to 3750 switch become hanged for few min.This happen for some particular interval.users accessing this server becomes entirely hanged for few min,then i have configured port monitor cmd and i have installed one wildshark tool to host connected directly to that switch.
View 3 Replies View RelatedI am experiencing the same problem described in this post {URL}. I have seen this happen on different networks, with different equipment attached. It happens on both 2960 and 3750 switches. Basically the connection drops, and we see in the web interface "Port is Disabled". This appears to happen every 10 minutes.
On the CLI, the status shows as connected.
Port Name Status V lan Duplex Speed Type
Fa0/38 connected 1 a-full a-100 10/100BaseTX
I have ran cable diagnostics while the drop out is occurring.
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ----------------- ----------- -------------------
Fa0/38 100M Pair A 28 +/- 15 meters Pair B Normal
[code]...
During the outage, I see the duplex fluctuate between full and half. The outage occurs for approx 90 seconds. If I fix the duplex and speed at both ends, the outage reduces to around 30 seconds. If I apply spanning-tree port fast the outage reduces further to around 10 seconds. Before I change any configuration on the port, the logs show the interface going down
Aug 16 13:06:51.875: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/38, changed state to down
Aug 16 13:06:52.874: %LINK-3-UPDOWN: Interface FastEthernet0/38, changed state to down
[code]...
However, once I apply the configuration nothing is logged. However we can still see the connection is disappearing for around 10 seconds. I suspect the issue wasn't resolved for the person reporting the problem in the link above, but because the outage is minimized, and not being logged it is going unnoticed.
why does my internet disconnect every 10 minutes with a hard wire modem,an then start working for 12 to 24 hrs.
View 1 Replies View RelatedI have a D-Link 655 and I want to restrict my guest zone more.
1. Is there a way I can make devices disconnect if they're not active after 30 mins?
2. Is there a way that I can restrict my Guest Zone to ONLY use b and g NOT n?
i have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
View 1 Replies View RelatedRecently my connection went haywire , it constantly disconnect and spike when there is 2 computers connected to the rounter but it works fine with 1 computer.contacted the ISP , they sent someone down just to change the modem but the problem still occurs[CODE]
View 9 Replies View RelatedI have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedWe have computers that are connected to a switch stack of 3 - 3750 switches. Randomly, we experience pcs that fail to communicate on the network. At first thought I figured the port went into err-disabled state, however the port shows up fine on the switch and moving the pc to another port on the same switch in the stack fails to fix the problem. To add to the confusion, if I immediately connect a different machine into the problematic port the newly connected machine has no issue and operates normally. Connecting back the first machine still results in no connectivity.
The only way to gain back network connectivity is to move the pc to a different switch in the stack. shut/no shut doesn't work.The IOS the stack is running is 12.2 and the switch ports are configured using cisco port macros.
here is how all the ports are configured.
switchport mode access
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
macro description cisco-desktop
spanning-tree portfast
spanning-tree bpduguard enable
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
May I know why my 2960S-48TS-L takes 10 minutes to boot and start, some just take 1 minute, but one of them take up to 10 minutes, but after that it works fine, why?
View 2 Replies View RelatedAfter insertion of SFP module in the Switch i have messages bellow and the switch hangs after couple of minutes it restarts
[Code]....
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedI have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having a strange problem where I'm not able to get through a Cisco 2960-S L2 switch when connected through vpn, while LAN-WAN traffic is working fine.The situation on site is the following:When inside the network I'm able to get to the internet without a problem. The problem is within a vpn-session. When this session is succesfully started I can ping and manage the Cisco 2960-S switch, but I can't ping or manage the Dell switch from my laptop. I can however ping the Dell from the Cisco-switch. [code]
View 7 Replies View Relatedset up my QoS on two 2960
-------------------- ------- ------- ------------
PBX Asterisk |----|2960-1 |------|2960-2 |-----|Voip client2|
-------------------- ------- ------- ------------
-------------- |
[Code].....
This will be this configuration for all input interface right ? For the Output part I'm lost, what do I have to do ? And for the 2960-2 do I have to put the same configuration ?
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies View RelatedWe recently updated a site2site link to metro ethernet, ISP call it 100mbps LAN Extension, but to me it is just QinQ over fibre connection. Most went well, one thing (annoying to me) is we can not ping our switches on both ends anymore.
We have a 3750 in headend and another 2960 on the other end. I used to be able to ping/telnet to the management IP from one to the other. Now we can not. I think the ISP is applying some configuration on ports of their customer-premises equipments (both are Cisco switches) but agent in ISP told me no. I thought there is some configuration on Cisco switch to block "MAC discovery" but i just can not remmenber what was that and google also failed me this time.
I have got two links from the same ISP, primary and secondary and connected to two different switch. The ISP have passed the trunk vlan of 30, 31 and 32 on both of the links. The ISP can't provide stp. I have got another managed 2960 series switch. How can I obtain failover on switch level.
View 2 Replies View RelatedI have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
My cisco ios 2960S is crashed and the ios is gone The issue is i am connecting my pc to management port and i give switch:
IP_ADDR x.x.x.x/255.255.255.0 and also switch: DEFAULT-ROUTER
But i can not copy tftp to flash,according that i have L3 port (management) why should i use xmodem?
I have 2 switches connected Via MM fiber cable one of them SRW2024-K9-NA with MGBSX1 Transceiver and the Secand One 2960 with GLC-SX-MM
are there is any configration must be done or not ?
Have Cisco catalyst 2960 IOS ver12.2(53)se2 when power on the power LED does not come up and on this is what shown on hyper terminal. what need to be done for this switch ?
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: b4:d9:8d:27:4c:00
Xmodem file system is available.
[code]......
Interrupt within 5 seconds to abort boot process. Boot process failed. The system is unable to boot automatically. The BOOT environment variable needs to be set to a boot able image.
I currently have a network with (8) 2960 Cisco Switches. (6) of the 2960 switches are etherchanneled back to (2) 2960 switches in the computer room. I would like to setup QOS on the (8) switches, however the traffic is very differnt on each of the switches. I have video, ip phone, server, printer, PC traffic. I am not sure what the best method of separating this traffic into differnt QOS queues.
View 3 Replies View Relatedwe have a cisco 2960 48 port tcl switch port and i've enable ssh on my switch and now :
1) how can i login to ssh ? how should create username for ssh ?
2) how can i disable telnet ?
3) how can i change main (master) password?
I have an switch 2960 and i have made an SSH connection . But the problem is that whenever i try to open with my teraterm or putty it ask for username and after that password but does take the password. It shows an error of password what should be the problem.
Commands that i entered to make SSH
config# username admin password pankaj
config# ip domain-name home.local
config# crypto key generate rsa
config# 1024
config# ip ssh version 2
I have an switch 2960 and i have made an SSH connection . But the problem is that whenever i try to open with my teraterm or putty it ask for username and after that password but does take the password. It shows an error of password what should be the problem.
View 1 Replies View RelatedI have a problem with may Cisco, it´s not start, only works the fan, the problem began when y turn down the Cisco and turn on again, but it´s not start. can something tell me what happen whit it.
View 1 Replies View Relatedhave a 2921 with 3 segments, let's say 172.16.0.1/24, 172.16.2.1/23 and 172.16.5.1/24
How can I browse for computers (in Network... Windows xp/7) from other segment?
We are going to upgrade our IOS on our WS-C2960G-48TC-L. But before we do that i want to ask whats the best IOS release to choose. Why we want to upgrade is because our switch software now don't support ssh just telnet access
Switch details:
Model: WS-C2960G-48TC-L
SW Version: 12.2(25)SEE2
Image: C2960-LANBASE-M
I was thinking about upgrading the IOS to 12.2(44)SE6 are maybe i should upgrade it to a newer release?
One more thing we have a bunch of stacked 3750 switches, that also need to be upgraded.
