Recently my connection went haywire , it constantly disconnect and spike when there is 2 computers connected to the rounter but it works fine with 1 computer.contacted the ISP , they sent someone down just to change the modem but the problem still occurs[CODE]
View 9 RepliesMy Internet will disconnect & then reconnect constantly. I have 2 laptops & they are both on my home network & I have no trouble with the other one so I assume there is nothing wrong with both the Internet service & router. The laptop with the problem is an acer/aspire 5720z. The Wireless Network Adapter is a Atheros AR5007EG. When I go to the Adapter Properties the status reads "The device is working properly". When I go to Control Panel>Network & Sharing Center my Wireless Network Connection Signal Strength reads Excellent. The operating system is Windows Vista Home Premium.
View 5 Replies View RelatedAfter years of my laptop running flawlessly, I've started having major problems connecting to my router/the internet.I noticed the problems started happening after I did a huge 14gb download.. My computer constantly but randomly disconnects for random intervals of time. If I'm lucky it'll connect just fine, but once it disconnects, it'll most likely not work for quite some time.The other computers/cellphones/etc aren't having any problems with connecting, and it's only my laptop.Sometimes it seems to go on a "Identifying...(Name) No internet access" loop, or it connects to the router, but I get no internet access. And whenever I troubleshoot it, I never get a consistent reason as to why it isn't working.The laptop is an Asus running Windows 7..
Windows IP Configuration
Host Name . . . . . . . . . . . . : Katie-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
i'm using 2960 cisco switch and every department has a switch same model, i have noticed that every 10 to 15 minutes my network is disconnected for atleast 10 seconds and all client conneted to the server was disconnected also.
View 26 Replies View RelatedBroadband connection is very slow and goes dormant even when moving mouse on web page to try to initiate applets. Computer locks or freezes constantly in between pages or when trying to open other pages on websites. Takes really long to try to do anything on computer when online.
View 2 Replies View RelatedIll get on my laptop and it will connect for 45min-hour and then it will disconnectEverything says connected on the laptop and the router and modem are connected and working. I have tried restarting my router and modem and even clean installed windows and reinstalled drivers. Nothing seems to work. Im posting from my old laptop and it seems to happen on this computer as well. This has never happened before.
View 9 Replies View RelatedThere are 3 people in my house that are connecting to the internet by a single modem router, everything is fine when there is only 1 of us online , but when there are 2 or 3 of us online , our download & our upload speed dramatically decreases . So is there a way to maintain our normal download & upload speed even when all 3 of us are online ?
View 10 Replies View RelatedThe issue is a odd one, I will be playing a game League of Legends, Star Craft 2, Diablo 3, or Tera and I am in Team speak then about 5 minutes to an hour I get "Connection has been lost". I am either booted from the game or Team speak, never both. It's completely random when this happens and at times it takes a while (10mins at the longest) for me to log back into what ever program I have been disconnected from other times the reconnection is instant. I have gone through forums, talked to support for the games, had my ISP come out and test my lines and replace my modem and network card, Ping tested, Speed tested and the results were stellar, but I still have the problem and so I feel that the problem is on my end. I have a self built machine, My OS is Windows Vista 64-bit, Mobo-EVGA 132-CK-NF79 2, Processor-2.85 gigahertz Intel Core2 Quad.
View 3 Replies View RelatedI've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....
Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies View RelatedI have 3 laptops connecting wirelessly to this router. One is running at 18Mbps, the other two at 0.4Mbps. the internet setting are the same and the security is the same (WPA2-Personal with AES encryption). One of the slow computers is brand new and WAY faster than my "fast internet" computer. The other is about the same as the "fast internet" computer. I updated the I connected the new computer to the router tusing an ethernet cable and it had superfast internet. I redid the Cisco connect on each computer, but it didnt change anything. Why is it so slow wirelessly?
View 4 Replies View RelatedI called my internet provider to come fix the problem and my internet was working PERFECTLY. Until, it started to mess up again. I don't know, what's wrong with it AT all. The Linksys box is working fine, the ROUTER is working BUT, my internet keeps dropping and takes HOURS upon HOURS to come back on, UNTIL I reset the Linksys box. Then it stays on for a bit. A few hours or a few minutes then suddenly, "No internet access."
View 3 Replies View RelatedEverything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View Relatedi want to connect two computers to run the same program, they are conneted to a router and both have internet. i doing this for tax season and i want them to run the same program and have the same information on them.
View 5 Replies View RelatedCan I make them share a single HDD? Like for booting windows, loading games and stuff? All 6 computers to have ONE single HDD? Will save me tonnes of money if this is even possible?
View 8 Replies View RelatedIve been having an issue for the past 3 weeks keeping my primary wired PC and the wireless PCs in my home network connected to the Internet. The internet constantly disconnects intermittently (with no rhyme or reason) and have tried everything I could do to try to resolve the issue. I connected my wired PC directly to the Optimum Online Cable Modem (Arris Telephony Modem v 3.0) I use to connect to the internet and it still has connection issues. Most of the time when it drops the connection, the network icon on the taskbar says I�m still connected to the internet. Only after a few minutes will the network icon finally appear with the yellow exclamation point over it. When I right click the network icon, I will check the network and sharing center and will click on the red x over the connection from my router to the internet. Sometimes when Windows checks for internet connection problems, it will state that it cant resolve the issue, and other times it will state that the DNS server isnt responding or cannot communicate with Primary DNS Server. I�ve had my ISP cable guys check my cable wire (coaxial cable wire) for packet loss, swapped my old router for anew one (twice), readjust the connection outside for a specific low node issue, and did 3 or 4 trace routes, conducted a multitude of ping tests, went on speedtest.com to check the signal strength and they state that everything looks great on their end. I also used different Ethernet ports built into the motherboard of my PC to see if my network adapter was the issue, but my internet connection it still continues to drop, even when only my pc is wired directly into the cable modem. I even changed the Ethernet cables themselves to see if they might have been faulty, but it still continues to drop.
I forgot to mention that I did the flushdns and registerdns commands , plus reset the TCP/IP, but my internet connection still continues to drop. The only thing(s) I have not done is change the network adapter completely (install a new Network PCI adapter ) and have the cable guy re install an entire new coaxial cable wire, of which myISP is adamant that I don�t need to have done since when I am able to connect to the internet, my signal strengths and speeds are great (download speeds of 32mbps and upload speeds of 5mbps). I know I�ve said a mouthful, but Im at a loss of what I should do next. When connected to my cable modem through my wireless N router, ALL of my PCs (my wired PC and my wirelessly connected PCs through my home network)will disconnect from the internet . Both the cable modem and the wireless N router still appear to be online (none of the lights on the front of the modem or router have changed ) I�ve even considered the strength of the ethernet cable itself, possibly thinking that the ones I have may not be strong enough for my internet speeds (purchased a CAT 6 Networking Ethernet Cable). My router , OS, cable modem, ISP, motherboard, and built in network adapter specs are shown below;
ISP: Optimum Online (with Boost Service) OS: Windows 7 Ultimate (with latest Windows 7 Service Pack 1 updates) Cable Modem : ARRIS Touchstone DOCSIS 3.0 E-MTA Telephony Modem TM802 Wireless Router: Netgear Rangemax Dual Band Wireless N Gigabit Router WNDR3700 Motherboard: ASUS Rampage Formula Built In Network Adapter: Dual Gigabit LAN (2 RJ45 Ports)
if you have two no of win 7 computer , and you run ping command at the same time at both PCs but the successfull at only one PC , second computer shows unsuccess full ping
View 2 Replies View Relatedhow can we share files between computers that connected through switch,also how we can apply password,and share between only some computers?
View 3 Replies View Relatedanother computer is connected to my home network, and i want to remove them as i don't know who it is. I also notice my files have been very recently shared within the 'homegroup'. i have not personally done this.is someone accessing my computer?
View 3 Replies View RelatedBasically, my home network is comprised of a WRT54GS Router which the cable modem and my main computer are plugged into (as well as vonage, networked printer). That leaves one port open which is used to connect a Dlink DES-1105 10/100 switch. I am connecting it using a crossover cable, though that was not necessary.I just noticed that a computer connected to that switch gets MUCH less download speeds at speedtest.net, and it gets STUCK on the upload test (doesn't even start).I unplugged it and plugged it directly into the router for testing. I get 20-30 megs down (like I should), rather than 5-11 like the switch gave me (ONCE the switch gave me over 20, not sure why..)The upload test NEVER runs though. I've tried different computers as well. I tried setting the computer to "100 full duplex" manually and no luck.
View 3 Replies View RelatedI have multiple macs and when all of them are connected to the wag120n router, macs can't seem to find/see each other as if they are connected to different networks. I have tried another router ie. netgear dg834g router and this problem didn't occur and i am able to connect over the network without a problem. Obviously there is something wrong with the router settings.
View 2 Replies View Related1) We have a server running active domain, and it also assign the IP address to domain users.
2) All the server, computers are connected to Cisco ASA5505 for the network.
Currently our VPNs were set up to use DHCP and local IP pools. It seems that I can get into the network, however the IP address the VPN gets was from the internal pool not From SERVER. As a result, the VPN is connected, by VPN is not able to ping to the router or the server. Is there anyway, I can configure the router treats VPN as the physical port. then the active domain server can assign the IP address to VPN.
I need to change my password. There are other computers accessing my Wi-Fi. How do I disconnect them and block so only I can access my account.
View 1 Replies View RelatedMy Dlink DIR-615 had worked flawlessly for almost 7 months now.But since last week it started showing problems.All the computers connected to LAN thru the switch could not access the Internet but the Server(192.168.0.100) which is connected to the DIR-615 could connect to the internet.the above screenshot was captured thru a laptop running Win7 Ultimate connected to the DIR-615 thru WiFi-n.Even after repeated Reloads the same error cropped up in the browsers in the computers connected thru the switch.The computers connected to the switch could access the Internet after I restarted the router.
View 7 Replies View RelatedMy Wi-fi on my rig seems to have some odd problems. When I'm gaming i often get a lag spike every 10-20 second or so, and before I got the "Vista anti-lag" program I was also getting the enormous 60 second lag spike. I'm sure many Vista users recognize this problem. But here is the deal, the first kind of lag spikes completely disappear while talking on Skype! Which makes me wonder, what is it with Skype (only while talking) that removes the lag? Gaming with Skype makes all games run fluently without any spikes at all.
View 2 Replies View RelatedIn our ASA 5520 " tmatch compile thread" process is taking too much CPU while applying ACL for a moment . CPU goes to high and then back to normal .. The code is 8.2(5) . Is this a normal operation or abnormal .
View 5 Replies View RelatedI am running XP pro. I have checked thoroughly for viruses/malware/etc. and everything appears to be clean. I have up to date drivers for NIC's, have cleared all temp data, done basically everything that the first tier Time Warner Cable(my ISP) tech support people will tell you to do as they read from that frustrating script we're all too familiar with and have had to deal with time and time before, including resetting modem and router, bypassing router, etc. etc. et bloody cetera.Ran several pings to a variety of servers and noticed ping spikes every 10or so seconds into the 300-600 range from an average of about 20-30ms.
View 5 Replies View RelatedI have a T1 connection to one of my sites, I am running HREAP with 4 AP's. I have been noticing a spike in traffic from my AP's to the WLC. Even when no one is on the wireless. When you use encryption (DTLS) should this cause spikes on the T1 ?
View 2 Replies View RelatedIn my customer having 3750 switch and they have simply assign IP address for vlan and enable telnet in switch and other things are same as default switch.In this switch they have connected 8 cisco layer 2 switches(6 managed and 2 unmanged switch) and approximately 5 servers connected in this switch.In a particular interval,users accessing File server are connected to 3750 switch become hanged for few min.This happen for some particular interval.users accessing this server becomes entirely hanged for few min,then i have configured port monitor cmd and i have installed one wildshark tool to host connected directly to that switch.
View 3 Replies View RelatedI recently puchased the WMP600N, connects great, I can browse the internet and even download without a problem.But when I try to play games such as world of warcraft, warcraft 3, (basically games that require immediate constant data transfers), I get 2-4 lag spikes every couple of minutes. As you might notice, this is a huge problem for many online games.
View 9 Replies View RelatedWe have a Catalyst 3560G 24 port POE switch. It's been running fine for 1+ years. A few weeks ago we enabled SPAN on it to capture packets. Today, we had a random spike in CPU on the switch. Seems hardware swithing continued to work fine, but software based processes choked and effectively took down EIGRP, HSRP, etc. We collect syslogs from the router and we saw 2 crashes/reboots. Both showed the exact same error both times, with the same hex values. I **believe** the CPU usage dropped when a tech disconneted the SPAN port and it's state changed to down, but I'm not 100% sure.Could this indicate an IOS bug (I'm hoping it's not a hardware failure)? And, how to track this down to see if this could be related to SPAN? I've disabled SPAN for now.
View 3 Replies View RelatedI am having a cisco 7609-S router with the image sup-bootdisk:c7600rsp72043-ADVIPSERVICESK9-mz.122-33.SRD7.bin. Im getting above 95% cpu spike for 10 mins in every 2hrs of interval, after it has been integrated with Ciscoworks LMS version 3.2.1 and added this to HUM. In LMS the HUM polling has been configured for every 1hr to monitor the cpu and memory utilization.
I have gone through the below cisco document and I have configured all of the snmp-server view commands as illustrated in the below website.[URL] After configuring the same, now we are observing the cpu spike every 4 hrs or i would say 5 hrs... I have checked all the settings of ciscoworks LMS and there is absolutely no other jobs are running in the day time... The spike comes every 4 hrs.
I recently downloaded the crysis 2 demo. But i disconnect 2-5 minutes into a game. I tried playing while directly plug into the modem and i can play as long as i want.
I am currently using the D-Link DIR-615 HW VER:c1 FW VER:3.13.Crysis is the only game with this problem at the moment. I have tried googling it but still won't work.I have tried to disabled my firewall+antivirus and i still disconnect.