have a 2921 with 3 segments, let's say 172.16.0.1/24, 172.16.2.1/23 and 172.16.5.1/24
How can I browse for computers (in Network... Windows xp/7) from other segment?
I have a WAN router that's on 172.x.x.x segment, and another WAN router that's on a 147.x.x.x segments.How can I make them communicate, I would like to interconnect both segments to talk to each other.We are using a Cisco 2800 on both segments.
View 8 Replies View RelatedWe have Linux server (CentOS) and nearly 120 computers in the local network (192.168.1.0 255.255.255.0) and nearly 20 computers have their own IP-address (real address). Periodically the 192-network computers can't browse the Internet; ping to the server is working; computers which have their own address are working properly
View 1 Replies View RelatedI have a new Cisco 3925 router. I have 2 network segments 10.0.1.X with net mask 255.255.255.0 and 10.0.2.x woith netmask 255.255.255.0. I have an internet gateway router at 10.0.1.21. I have set GBethernet 0/0 to 10.0.1.1 / 255.255.255.0 and GBethernet 0/1 to 10.0.2.1 / 255.255.255.0. I have set a static route 0.0.0.0 / 0.0.0.0 to 10.0.1.21 for gateway of last resort.
When I setup a workstation on the 10.0.2.X segment at 10.0.2.100 wirh a gateway of 10.0.2.1, I can ping 10.0.2.1 and 10.0.1.1 but can not ping anything else on the 10.0.1.X network or on the internet. When I am connected to the console port on the router I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and any address in the internet but I can not ping 10.0.2.100.
When I am on a network connected to the 10.0.1.x network af 10.0.1.100 I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and anywhere on the internet but can not ping 10.0.2.100 or any other address on the 10.0.2.x network other than 10.0.2.1. What Do I need to do on the 3925 to get to all address on each segment and to get to the 10.0.1.21 gateway from the 10.0.2.x addresses?
We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
Now I have a 172.16.0.0/16 network with a def. gw. for internet where is a MS Forefront TMG 2010 with BSplitter for traffic shaping. I purchased an 2921, 2,5 GB RAM, security+data license and an EHWIC-D-8ESG.
I made 4 subnets in a test environment with some access-lists, nothing fancy yet. How can I use FF TMG for bandwidth management, where should I put it? For those 4 subnets the def. gw. is, normally, the 2921 router. TMG is splitting traffic by client IP.
We have two offices separated by a WAN.Office A is our main office that has all of our servers, including domain controllers and active directory, on our own network.Office B is a temp. office that is piggybacking off of our sister company's network, but the computers there still connect back to Office A servers to login/access services. However, Office B connects to the sister company's local domain controllers for DNS/WINS.We're having an issue where NetBIOS names of the other office are not always showing up when browsing for computers within the WinXP Windows Explorer (My Network Places --> Entire Network --> MS Windows Network --> domain A). It seems entirely random whether or not we can see the other office's computers. We can still ping/remote to them, but cannot browse to them.
It would normally be a non-issue, but some of our software apps require us to "Browse" to the network server location, rather than being able to type in the address, during installation. Can't install if we can't browse the Office A servers. Obviously has something to do with WINS not always populating/updating, but I'm not sure what or how to fix this.
I am using Cisco ASA 5505 between my two network.
1) I want 192.168.1.0/24 LAN user can go to access 172.16.1.0/24 network but 172.16.1.0/24 cant access 192.168.1.0/24 network
2) what interface nameif will be or security Laval
3)what access list should be configure
4)what IP route should be used
We are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
i have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
We have remote office where we have 2921 router with 6 layer 2 switches. We have few servers which need to be in specific vlan.
2921 router does not have switching engine we are using this to support VOIP.
So on 2921 router i created 6 sub interfaces for each vlan and assign them to their specfic vlans. Then I have trunk connection to switch 1. Now switch 1 connects to all other switches in the network. As our company design all layer 2 switches should be transparent mode. i tested them i can ping from one switch to all other switches.
Router vtp mode i set to transparent mode and from all switches i can ping the router sub interfaces.
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
configuring up a 2921 router for remote site which is fitted with 24 port Etherswitch module.As part of this setup I have defined 3 vlans on the router, but when I go onto etherswitch and for example set switchport access to access vlan 3 it is not aware of this vlan.Do I have to set up trunk inbetween Router and its etherswitch?Wish I had ordered seperate switch as it would have been easier or am I missing something.sho vlan-switch shows my vlans but on swicth sho vlan brief does not.
View 10 Replies View RelatedAn interface on 2921 router is not coming up. When I shut/no shut the interface, I see this:
Router#sh log | i 0/2
Oct 17 08:55:06: %IP_VFR-7-FEATURE_DISABLE_IN: VFR(in) is manually disabled through CLI; VFR support for features that have internally enabled, will be made available only when VFR is enabled manually on interface GigabitEthernet0/2
Oct 17 09:00:35: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
[Code]...
This is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
I have a 2921, and I have 4 network segments. In segment 172.16.0.0./27 I wand to "pair" somehow connections. I mean IP 172.16.0.x has to have MAC aaaa.bbbb.cccc and so on, and not accept connections otherwise.How can I do that?
View 7 Replies View RelatedIs it possible to configure a Cisco2951 and a Cisco2921 in HSRP?
View 1 Replies View RelatedI have a 2921 with 4 segments: [code] My DHCP server is 172.16.5.2 and I need to serve clients from 172.16.2.0/23 by MAC address and only to that segment.
View 2 Replies View RelatedWhat I’m looking to do is setup a net-flow monitor for traffic going across a PIX firewall. I know unfortunately I can’t do this directly from the PIX because it does not support net-flow.
I do have a 2921 router on the same network that I have net-flow enabled to monitor traffic across the MPLS Connection.
Since the traffic for the MPLS is going out a direct interface I have applied the IP Flow egress/ingress commands to that interface to obtain the net-flow data I need. The PIX firewall however is not a direct interface so this can’t be done. I have done a little reading and believe I could use a policy map to create a “filter” so that any traffic that meets the ACL associated with the Policy-Map would get sent to net-flow monitor.
My question is how do I set that up so that so I can have the two net-flow data “streams/sources” go to separate net-flow ports so that I can monitor them independently of each other or is that not possible?
Both devices are connected to a 3750X switch; however neither is connected to a 10GB port. To my understanding that means I can’t run net-flow on the switch itself.
got a RPS2300 with 4 cat3750g48ts on it (yeh I know - Cisco documentation allows only 2 of them ). What will happen if I connect an additional Cisco 2921 router?
View 0 Replies View RelatedI have a 2921 where I am shaping some traffic based on sub net on my lan. I have applied the shaping policy to the lan interface in the outgoing direction.
Topology is as follows:
ISP - ASA - ROUTER - LAN
Policy map:
Policy Map shape-lan
[code]....
I am seeing a lot of no-buffer drops on the policy and I am wondering what the best solution is to solve this:
Class-map: tc-class (match-any)
8730680 packets, 10803689863 bytes
5 minute offered rate 4453000 bps, drop rate 0 bps
[code]....
Should I just be increasing the queue-limit or should I be changing something else?
I have a 2921 router and want to use mpls feature. Right Now we are using c2900-universalk9-mz.SPA.151-4.M1 image but mpls static cross connect” is not working with this image. And will this image(c2900-universalk9-mz.SSA) be worked?
View 2 Replies View RelatedI can not find any information about management port of Cisco ISR 2911, 2921 and so on. There is management port in specification of 2911 and 2921 and I do not know if this port can be as a simple Ethernet port – forward traffic in/out on L3.
View 2 Replies View Relatedthe cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
View 6 Replies View RelatedI have 2 links to 2 different departments switch with an up link of 10mb. I want to guarantee that both departments get at least 5mb, but can use part of the other 5mb that not in use. Is this possible?
View 3 Replies View RelatedOn 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedI have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View RelatedI have a Cisco 2921 and a 3750 stack. I want to use both interfaces on the 2921 to connect to the 3750 stack switch 1 and 2. Is this possible using same ip subnet?
View 2 Replies View RelatedI am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
i have an 2921 connected to an Catalyst 3560. My router interface shows quite a lot of input queue drops. Load is not too much max 5/255.
View 1 Replies View Relatedi'm using 2960 cisco switch and every department has a switch same model, i have noticed that every 10 to 15 minutes my network is disconnected for atleast 10 seconds and all client conneted to the server was disconnected also.
View 26 Replies View RelatedIn my customer having 3750 switch and they have simply assign IP address for vlan and enable telnet in switch and other things are same as default switch.In this switch they have connected 8 cisco layer 2 switches(6 managed and 2 unmanged switch) and approximately 5 servers connected in this switch.In a particular interval,users accessing File server are connected to 3750 switch become hanged for few min.This happen for some particular interval.users accessing this server becomes entirely hanged for few min,then i have configured port monitor cmd and i have installed one wildshark tool to host connected directly to that switch.
View 3 Replies View Related