I have a WAN router that's on 172.x.x.x segment, and another WAN router that's on a 147.x.x.x segments.How can I make them communicate, I would like to interconnect both segments to talk to each other.We are using a Cisco 2800 on both segments.
View 8 Replieshave a 2921 with 3 segments, let's say 172.16.0.1/24, 172.16.2.1/23 and 172.16.5.1/24
How can I browse for computers (in Network... Windows xp/7) from other segment?
I have a new Cisco 3925 router. I have 2 network segments 10.0.1.X with net mask 255.255.255.0 and 10.0.2.x woith netmask 255.255.255.0. I have an internet gateway router at 10.0.1.21. I have set GBethernet 0/0 to 10.0.1.1 / 255.255.255.0 and GBethernet 0/1 to 10.0.2.1 / 255.255.255.0. I have set a static route 0.0.0.0 / 0.0.0.0 to 10.0.1.21 for gateway of last resort.
When I setup a workstation on the 10.0.2.X segment at 10.0.2.100 wirh a gateway of 10.0.2.1, I can ping 10.0.2.1 and 10.0.1.1 but can not ping anything else on the 10.0.1.X network or on the internet. When I am connected to the console port on the router I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and any address in the internet but I can not ping 10.0.2.100.
When I am on a network connected to the 10.0.1.x network af 10.0.1.100 I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and anywhere on the internet but can not ping 10.0.2.100 or any other address on the 10.0.2.x network other than 10.0.2.1. What Do I need to do on the 3925 to get to all address on each segment and to get to the 10.0.1.21 gateway from the 10.0.2.x addresses?
We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
I am really new to Cisco and having a hard time with my Cisco 2800 series.
I have two sites connected with each other Site A and Site B (Using the same Cisco 2800). Now site A can connect to site B on the Cisco and the internal network, but site B can only see the Cisco and not the internal network of site A. So all the traffic is coming in to site B but can't break out of site B. I have tried everything I can think of but again my knowledge of Cisco is not good at all.
I'm trying to get a node in SVI1 on VRF1 to speak to another node in SVI2 on VRF2 to reach each other. After hours of failure, I went to outside resources. Everything I read on the internet says it's not possible on this platform and at least one TAC engineer seems to agree.
I just can't believe such a high-end data center switch is not capable of handling such a basic feature.
I have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies View RelatedI am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies View RelatedI am using Cisco ASA 5505 between my two network.
1) I want 192.168.1.0/24 LAN user can go to access 172.16.1.0/24 network but 172.16.1.0/24 cant access 192.168.1.0/24 network
2) what interface nameif will be or security Laval
3)what access list should be configure
4)what IP route should be used
The layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
I've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
Is there any official Cisco reference to describe what is considered to be the highest acceptable production CPU load on 2800 routers? I found the document "Integrated Services Routers G2 - Performance Overview" that states at page 5,Most service providers set their CPU alarms to 60 or 65 percent. Many enterprise customers are comfortable running production networks with CPU around 70 or 75 percent.
View 3 Replies View RelatedI have a router with two interfaces what i need to filter the HTTP traffic from one interface and the rest of the traffic through the other on my cisco router 2800.
View 3 Replies View RelatedI have a problem to create a VLAN with a Cisco 2801.,I need to have base ports FastEthernet 0 / 0 and FastEthernet 0 / 1, in the same VLAN.
Basically I'm trying to switch access redundacion, now I have redundant switches in which I have the servers, but if one of these switches fails, and,coincidentally is where I have connected the router, the server runs out of internet connection.,I idea is to connect the FastEthernet 0 / 0 to a switch, and FastEthernet 0 / 1, to the other switch,but I managed to have these two ports in the same vlan, in order to have a unique IP for both FastEthernet ports,As I can do this?. do is a lot of documents using the switchport command, but this command is not available in my router, I tried different IOS, and nothing.,currently I have the following IOS: c2801-adventerprisek9-mz.124-24.T6.bin
I have a 2800 router and tried so many ways to block the unwanted sites on my office network.Like access list ip based, null0 routing and policy map. Faced issues with below config
1. Creating Access-list. very difficulty to block the sites with https those sites will be opend, and we cant block all the IPs
2. Creating null0 routing. it also a bit deficult the block maximum sites because we can't fiend all IPs for those sites
3. Policy map.. with policy map we can only 1site we can block, but not more than one..
I heard that port based routing or port based access-list are the best ways to stop the websites in my local network..for this one i need to map the site to unsued ports then i need to null rouging or need to create the access-list.
I have a cisco 2800 router.. (flash:/c2800nm-advsecurityk9-mz.151-4.M4.bin, Version 12.4(13r)T11) configured DHCP, DNS, NATING and Bandwidth restriction...And to stop some social network [URL] i configured ip route 66.220.144.0 255.255.240.0 Null0 (rang of facebook address) But still i am able to open facebook.com in my network...
ADMIN-II_2811#sh run
Building configuration...
Current configuration : 1812 bytes
!
! Last configuration change at 17:26:33 UTC Sat Nov 24 2012
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
Needing to upgrade IOS on 2800 router from c2800nm-advipservicesk9-mz.123-14.T7.bin to c2800nm-advipservicesk9-mz.124-15.T13.bin. I noticed ther are several other files on the old code that may needed for booting up router but Im running low on memory. The other existing files are ;
c2800nm-advsecurityk9-mz.124-3i.bin
securedesktop-ios-3.1.1.45-k9.pkg
sslclient-win-1.1.4.176.pkg
Do I need these files for the upgrade or can i delete them when upgrading to 124-15.T13.bin. ?
How to setup redundancy on a 2800 series Router so that whenever it fails it will be routed through the MPLS router
View 5 Replies View RelatedI'm trying to turn off SSH version 1 & 2 to pass PCI compliance. Problem is, I cannot touch the VPN link between the two offices. I'm afraid the PKI certificate used for the VPN will be deleted if i zeroize the RSA key which seems to be the only way to stop the router responding on port 22.
Here is the stuff from the running config related to the crypto map:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[ code].....
I'm only CCNA so I'm not even sure if the certificate or RSA key is being used for the VPN link, but I can't tell from the running config that zeroizing it would be a good idea and not break the VPN. I'm open to other ways of disabling SSH, as we are able to just connect using a console cable. But it looks like denying port 22 with an access-list doesn't even stop the router from responding to the port.
I have a customer who has a Cisco 2821 router with software 2821/HSEC/K9 and they wish to upgrade to C2821-VSEC-SRST/K9.From my understanding they want to use the same router but install an IOS with the capabilites it has at the moment but with voice. [code]How do I go about pricing this up and what upgrade sku's will do this?I am not to worried about the memory.Is it just a simple ios upgrade as the srst licenses are on a trust basis?
View 2 Replies View RelatedMy Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
Just need to verify if HWIC-2T is compatible with the Cisco2800 routers?
View 4 Replies View RelatedI am in need to have the arp table cleared every 5 seconds or so on a 2800 router. I was wondering how I might be able to accomplish this.
View 4 Replies View RelatedI have Router 2800 series Global nating is configured on it.
ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
My object is that i want give internet access only for few users ip E.g IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedI have 2800 series router which is directly connected to ISP. How can secure the router from outside access; I am totally new to the security concepts.
View 2 Replies View RelatedI have a pair of router Cisco 2800 running in HSRP, now I want to configure one sub interface with another sub net, Will my current IP on physical interface work or do I need to create two Sub interfaces for each network. Do i must need encapsulation on sub interface
Current Config:-
Router 1:-
interface FastEthernet0/1description Connect to LAN_SW1 Gi1/0/1ip address 192.168.1.13 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 90standby 1 preempt
Router 2:-
interface FastEthernet0/1description Connect to LAN_SW2 Gi1/0/1ip address 192.168.1.3 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 110standby 1 preempt
For second network I do not require HSRP
Router 1:-
interface FastEthernet0/0description Connect to LAN_SW1 Gi1/0/1no ip addressduplex fullspeed 100
[ code]...
Router 2:-
interface FastEthernet0/0description Connect to LAN_SW2 Gi1/0/1no ip addressduplex fullspeed 100
[Code]...
I wish to block some url that users have access through my LAN .That's i wish to block icmp,access towards such sites, i wish to block icmp because dns will resolve the domain and they can access through ip address.what i have in place is a cisco 2800 series routers,
View 7 Replies View RelatedIs there a way to set static routes per VLAN?Example VLAN 100 sends all traffic to 192.168.1.1 and VLAN 200 sends all traffic to 10.1.1.1. (2800 Series RTR)I have 5 networks that have their own gateway to the Internet via satellite link. Those networks run over the same infrastructure on separate VLANs. They frequently send traffic to each other, which gets sent over a slow SAT link. I introduced a router to the network and would like to set all my hosts default gateway to the local routers sub-interface then have a static route that send all traffic that is not on one of my 5 networks back to that VLANs respective SAT modem to get routed out over the Internet.
View 4 Replies View Relatedwe have a 2800 series router functioning as our internet router and it will only forward packets to addresses with host entries in the routing table even if the network is directly connected.
View 18 Replies View RelatedI remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 Replies View RelatedI am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedI got a Cisco 2800 router and am planning to use FastEthernet 0/1 to trunk in 802.11Q VLAN's to cater for some of our radio links. speed and operation of the sub-interface that will be created. Or explain it here. We got a radio link that we want to trunk into this Cisco 2800 and it is suppose to be connecting at 100Mbps but currently operating at around 80Mbps. Reports shows that the max in and out traffic for this link this year till today is 25Mbps. Will it not fail teh CPU etc ?
interface FastEthernet0/1
no ip address
!
[Code]....