I can not find any information about management port of Cisco ISR 2911, 2921 and so on. There is management port in specification of 2911 and 2921 and I do not know if this port can be as a simple Ethernet port – forward traffic in/out on L3.
View 2 Replies
i have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
How does the IP address is assigned on management port of WS4507 R, syntax.
View 2 Replies View RelatedIs there some kind of trick to getting the fastethernet 0 management port to come up? My adjacent switch is up/up, but fe0 is down/down. I dont' see how this could be possible. I am getting all my info remotely, but I am pretty sure it's wired up correctly.
View 2 Replies View RelatedI attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies View RelatedWhat is the point of it? It is not a remote console. If i reboot the switch i cannot get back to the out of band management port unless the switch is fully running. Is this only for security purposees? so all telnet/ssh is from an Out of band network?
View 15 Replies View RelatedI'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies View RelatedOur out of band connections with the new routers (1941 & 2921) with the new IOS 15.0 are not working.
Here is our configs:
Router:
line aux 0 exec-timeout 3 0 modem InOut transport input all stopbits 1
Modem(D-Link):
at&fs0=1s2=127s37=9e1q1&c1&d2&s1&k0&r0&w
Here is an output of the debug command:
*May 17 05:02:14.206 UTC: TTY1: CTS went down on IDLE line*May 17 05:02:17.206 UTC: TTY1: CTS came up on IDLE line*May 17 05:02:22.206 UTC: TTY1: CTS went down on IDLE line*May 17 05:02:25.206 UTC: TTY1: DSR came up*May 17 05:02:25.206 UTC: tty1: Modem: IDLE->(unknown)*May 17 05:02:25.206 UTC: TTY1: EXEC creation*May 17 05:02:25.206 UTC: TTY1: create timer type 1, 30 seconds*May 17 05:02:25.674 UTC: TTY1: create timer type 10, 30 seconds*May 17 05:02:26.154 UTC: TTY1: pause timer type 10 (OK)*May 17 05:02:26.154 UTC: TTY1: resume timer type 10 (OK)*May 17 05:02:26.174 UTC: TTY1: pause timer type 10 (OK)*May 17 05:02:26.206 UTC: TTY1: DSR was dropped*May 17 05:02:26.206 UTC: TTY1: Set
[code]....
It goes into the handshake but then disconnects immediately.
I've got a client with a Management Port set up for Out-of-Band management. Here's the configuration of the interface and some relevant static routes:
interface Management0/0
description MGT
speed 100
duplex full
nameif Mgt
[code]...
The route through Mgt interface is required as my client accesses the device from a subnet that isn't local to M0/0.Unfortunately, now any traffic originating from outside and destined to 10.48.0.0/16 is choosing the Mgt interface. I had thought that the 'management-only' keyword prevents this from happening (traffic traversing between interfaces).
There is a broad scope of /16 addresses on the 'inside' so just swapping destinations won't work (the client wants to avoid a routing table with 50+ static entries, understandably)My temporary solution was to do this:
route inside 10.0.0.0 255.128.0.0 10.38.103.1
route inside 10.128.0.0 255.128.0.0 10.38.103.1
route Mgt 10.0.0.0 255.0.0.0 10.38.100.254
If 'management-only' doesn't prevent traffic from using the Mgt interface, what is the point of the command?
We are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
i have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
We have remote office where we have 2921 router with 6 layer 2 switches. We have few servers which need to be in specific vlan.
2921 router does not have switching engine we are using this to support VOIP.
So on 2921 router i created 6 sub interfaces for each vlan and assign them to their specfic vlans. Then I have trunk connection to switch 1. Now switch 1 connects to all other switches in the network. As our company design all layer 2 switches should be transparent mode. i tested them i can ping from one switch to all other switches.
Router vtp mode i set to transparent mode and from all switches i can ping the router sub interfaces.
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
configuring up a 2921 router for remote site which is fitted with 24 port Etherswitch module.As part of this setup I have defined 3 vlans on the router, but when I go onto etherswitch and for example set switchport access to access vlan 3 it is not aware of this vlan.Do I have to set up trunk inbetween Router and its etherswitch?Wish I had ordered seperate switch as it would have been easier or am I missing something.sho vlan-switch shows my vlans but on swicth sho vlan brief does not.
View 10 Replies View RelatedAn interface on 2921 router is not coming up. When I shut/no shut the interface, I see this:
Router#sh log | i 0/2
Oct 17 08:55:06: %IP_VFR-7-FEATURE_DISABLE_IN: VFR(in) is manually disabled through CLI; VFR support for features that have internally enabled, will be made available only when VFR is enabled manually on interface GigabitEthernet0/2
Oct 17 09:00:35: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
[Code]...
This is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
I have a 2921, and I have 4 network segments. In segment 172.16.0.0./27 I wand to "pair" somehow connections. I mean IP 172.16.0.x has to have MAC aaaa.bbbb.cccc and so on, and not accept connections otherwise.How can I do that?
View 7 Replies View RelatedIs it possible to configure a Cisco2951 and a Cisco2921 in HSRP?
View 1 Replies View RelatedI have a 2921 with 4 segments: [code] My DHCP server is 172.16.5.2 and I need to serve clients from 172.16.2.0/23 by MAC address and only to that segment.
View 2 Replies View RelatedWhat I’m looking to do is setup a net-flow monitor for traffic going across a PIX firewall. I know unfortunately I can’t do this directly from the PIX because it does not support net-flow.
I do have a 2921 router on the same network that I have net-flow enabled to monitor traffic across the MPLS Connection.
Since the traffic for the MPLS is going out a direct interface I have applied the IP Flow egress/ingress commands to that interface to obtain the net-flow data I need. The PIX firewall however is not a direct interface so this can’t be done. I have done a little reading and believe I could use a policy map to create a “filter” so that any traffic that meets the ACL associated with the Policy-Map would get sent to net-flow monitor.
My question is how do I set that up so that so I can have the two net-flow data “streams/sources” go to separate net-flow ports so that I can monitor them independently of each other or is that not possible?
Both devices are connected to a 3750X switch; however neither is connected to a 10GB port. To my understanding that means I can’t run net-flow on the switch itself.
got a RPS2300 with 4 cat3750g48ts on it (yeh I know - Cisco documentation allows only 2 of them ). What will happen if I connect an additional Cisco 2921 router?
View 0 Replies View RelatedI have a 2921 where I am shaping some traffic based on sub net on my lan. I have applied the shaping policy to the lan interface in the outgoing direction.
Topology is as follows:
ISP - ASA - ROUTER - LAN
Policy map:
Policy Map shape-lan
[code]....
I am seeing a lot of no-buffer drops on the policy and I am wondering what the best solution is to solve this:
Class-map: tc-class (match-any)
8730680 packets, 10803689863 bytes
5 minute offered rate 4453000 bps, drop rate 0 bps
[code]....
Should I just be increasing the queue-limit or should I be changing something else?
I have a 2921 router and want to use mpls feature. Right Now we are using c2900-universalk9-mz.SPA.151-4.M1 image but mpls static cross connect” is not working with this image. And will this image(c2900-universalk9-mz.SSA) be worked?
View 2 Replies View Relatedthe cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
View 6 Replies View Relatedhave a 2921 with 3 segments, let's say 172.16.0.1/24, 172.16.2.1/23 and 172.16.5.1/24
How can I browse for computers (in Network... Windows xp/7) from other segment?
I have 2 links to 2 different departments switch with an up link of 10mb. I want to guarantee that both departments get at least 5mb, but can use part of the other 5mb that not in use. Is this possible?
View 3 Replies View RelatedOn 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedI have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View RelatedI am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedI have a Cisco 2921 and a 3750 stack. I want to use both interfaces on the 2921 to connect to the 3750 stack switch 1 and 2. Is this possible using same ip subnet?
View 2 Replies View RelatedNow I have a 172.16.0.0/16 network with a def. gw. for internet where is a MS Forefront TMG 2010 with BSplitter for traffic shaping. I purchased an 2921, 2,5 GB RAM, security+data license and an EHWIC-D-8ESG.
I made 4 subnets in a test environment with some access-lists, nothing fancy yet. How can I use FF TMG for bandwidth management, where should I put it? For those 4 subnets the def. gw. is, normally, the 2921 router. TMG is splitting traffic by client IP.
