I'm trying to reset this router back to its original form (pass: admin (?)) but the ''hold the reset button for 45 seconds and unplug for 30 seconds'' just doesn't seem to work. When I try to install with the CD it just keeps saying that I have to reset it. how do you reset the WRT120N? Are the lights suppose to blink to indicate that you're done holding the reset bottom?
We've lost our WRT120N's administrator password and are trying to reset it to factory defaults.One peculiar thing that we have noticed is that the router has an IP of 192.168.106.1 rather than the default of 192.168.1.1 (this is verified by the default gateway, as well as a login prompt when 192.168.106.1 is put into a browser).Things we've tried to do to reset the router:
1) Press and hold the reset button at the back of the router for 30 seconds
2) Press and hold the reset button at the back of the router for 60 seconds
Interestingly, doing either of these things seemed to have no effect on the status lights.
I have WRT120N, i recently updated the firmware. 1.0.06. only my bad is i done it wireless. so its basically interrupted.I have tried, hard reset and power cycle and reinstall the firmware but still the problem occurs, this time its wired.it happens intermittently. i have tried pressing reset upon turn on and reinstall firmware on the bootloader. it stablized for a while but then disconnects and blinking stikes again.
Turns out one of the relatives changed the router name and password, and in a fit of brilliance, forgot to WRITE THE NEW USERNAME/PASSWORD DOWN!So I typed in 192.168.1.1 and tried literally every combination I know. NOTHING works tried rebooting the WRT120N. I tried both holding the reset button in, as well as holding the reset button in along with pulling the power adapter cord. Neither of these achieved the desired result (which would be the resetting of the factory username and password to "admin/admin".
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
I bought a Wireless-N Home Router MODEL WRT120N so that I could use my new Kindle Fire online, since I could never catch an open wi-fi signal in my house. Router IS correctly installed and working fine.....but when I go to use my Kindle, I see it on the list, click on it, enter my password.......and it tells my my password must be incorrect. I KNOW it is correct! I even went and CHANGED the password just in case!
My Kindle keeps giving the message "Unable to connect to the selected Access Point. Please check the password you have provided."
i'm attempting to access the router's configuration options (192.168.1.1) and it's requesting a user and a password, i have not set any of them so i'm using the defaults, been, user (blank), password (admin) but is not taking them; after 3 attempts it gives me a 404 error.
I have changed the router username/password in the past and either I can't remember it or its not accepting what I am entering, because the router logon will not go through. I have unplugged the router for 5 mins and then let it come back on and still cant get in, pressed the reset button down and let it come back up still nothing, and I have unplugged the cable modem and router for five mins and then plugged them both back up and I still can't get the router to reset to the default admin password. In the past it has worked before but now nothing I try will let me into the router interface to set up anything.
I got a problem with my router CISCO (DPC3825) where the eithernet is working properly and the wireless is not, and I had to plug the usb to make the setups, and suddenly the wireless was working but when I tried to reset the password something worng happened change the set of the wireles
I have an E3200 router and need to know how to reset the password... cant connect my tablet because it asks for cisco connect password and I have NO CLUE what it is... if i do the reset on bottom of my router will it let me reset my password???
im trying to reset my linksys WRT54G wireless router because im trying to change some settings. i tried the 192.168.1.1 and it asks for a password, but i dont remember putting one on....i tried the admin in the password field and empty name field but that dosent work.I've tried holding the reset button on the router itself for 10sec+ but that dosen't seem to do anything.
Is there a way to reset the parental password for the E300? I cannot figure out my Parental Passowrd and when I click recover passowrd I see my clue. From my clue I cannot get my password. So do I have to reset my router and start from scratch? Or is there another way to recover it.
WRT54G2. I forgot password , but have to reset anyway. Currently have desktop w/XP. a laptop w/Vista and will be adding a Widows 8 64 bit laptop.. Any special consideration for settup with the Window 8?
I was given this router (it's my 3rd one) and cannot get the reset button to reset the password. I have run throught a 30/30/30 reset as well as just holding the button in for the standard 30 seconds.
I know the router works, as in i can ping it. It asks for a password when i go to 192.168.1.1, but *blank* and "admin" do not work. When i click the cancel button it displays a pink(salmon) screen that says "401 Unauthorized Authrization required". (all of this is when i am connected to it with an ethernet cable to #1)
When it's sitting there it has an led lit over power and one ove wlan which flickers from time to time.
I have just moved and my ISP is the same ( Comcast) but I'm in a different region of the country. The former service (modem) was a cisco (1 port) that I connected my EA 2700 Cisco router to and it worked like a charm. My IP phones came right up as well. Now I have an modem/router combo (provided by my ISP) and when ever I attempt to connect to my VPN it will give me an error and not connect. I was told by my ISP that I could bridge the router and try that way.Do I need to set up all over again? or have the settings remained. Also I am unable to access my router with admin/password. How do I reset the password?
I changed my E1000 router name successfully, and then went into the Administration section to change my password. After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password. When I enter the exact same user name and password it does not accept them. When I try to enter the old user name and password it does not accept them either. I then try combinations of the two and it still will not accept the input. I have reset my router 4 times now and this keeps occurring. I am completely baffled.
COX cable was out yesterday doing some work outside our apartment building. Now, our CISCO LinkSYS WRT120N won't work. I was working before COX cable came out and has been working without problem for the past two years.When I plug the harddrive into slot 1 in the back of the router, "4" lights up. When I plut it into slot 4, "1" lights up. When I plug it into slot 2, "3" lights up, and when I plug it into slot 3, "2" lights up.I tried the router software, but when I reach the plug the router in step, the soft ware returns after a couple minutes and says it cannot locate the router, even though the router lights are on.
I have the CISCO Linksys Wireless Router Model Number: WRT120N. My laptop is finding the router, and connecting to it fine. However, when I try to log onto the internet, it says no internet connection (same in the available net work section in the menu bar).Internet (Charter) they have checked the modem and there is no issue. I have also plugged the Ethernet cord directly from the modem into the computer, and unable to access the internet.
For home use, I have a Windows Vista PC which is hooked up to the Internet via a wireless EV/DO modem that plugs into a USB port. I just bought an iPad and for connectivity, I then bought a WRT120N wireless router. But I cannot attach the EV/DO modem to the WRT120N since the EV/DO only has a USB port. I plugged the PC into one of the 4 ports of the WRT120N and the iPad sees the router, but what I would like is that it also sees the internet when the PC is online via the EV/DO modem. Is there a way to configure this? I realize that the PC would always have to be switched on if I want to have the iPad online, but for the time being I am ok with that.
Recently I bought a new laptop (Sony Vaio SVE1511HFXW) and I haven't been able to connect it to the internet wirelessly. I previously was working on a Sony Vaio VGN-NR series laptop that I had no problem setting up a wireless connection for. I ran my router set up disc on the new machine and basically everything got ruined. My other laptop lost it's wireless connection and connecting it with an ethernet cable didn't work either. So now both computers were not connected. Actually, all devices can't pick up the wireless anyway (I tried to get on netflix with my Wii and it didn't work) I restarted the router several times, reset it once and nothing happened. I could only connect with the cable after I reset the modem and router, but it's still saying it "can't detect an internet connection." When I ping the router I get an answer back.
Here's what I get when I run ipconfig in the command prompt:
C:UsersShinsei>ipconfig Windows IP Configuration Wireless LAN adapter Wireless Network Connection:
I am in a problem, my modem gets hacked everyday, such that many of the sites do not open and only "http://184.108.40.206/" opens instead of sites like yahho.com, sify.com. I checked on internet many people are facing such issue.Only thing I can do to resolve this is to reset my modem, but still this gets hacked even on changing my password.I am not able to understand how is it possible to modify the settings of modem when I have changed the password.Modem Model: Beetel 220BX.
I'm staying at a hotel where the internet offered is only wired. I can plug in the ethernet cable and no log-in is required. However, when I connect to the router and then try to access the internet from my laptop it does not appear to work.