The Connection To The Server Was Reset While The Page Was Loading
Jan 21, 2013
I receive the following error message:The connection was reset The connection to the server was reset while the page was loading The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.I am unable to connect to Facebook on my home computer, but can visit any other site with no problems. I can access Facebook from my work computer. I am using Firefox on both. I only use wifi as I only have a laptop and my router is in my office. I can access Facebook on my phone with my wifi enabled. I have not tried a direct wired connection (will try that next and let you know what happens) as I don't use my office, because it's currently full of junk.
Clearing the cache and cookies
Changed Firefox proxy settings to "no proxy"
Resetting my wireless router
Checking the Hosts file for facebook entries (there are none)
And still no access. The only way I have been able to access Facebook is by turning the firewall off on my wireless router (Belkin Wireless G). I don't want to have to turn the firewall off just to go on facebook. I am the only person in the house who uses a computer and the internet. So settings have not been changed, because I am the only person with access to change them (password protected wireless network as well).
When my wife gets chemo, we spend the day at the hospital, and I login to their WiFi as a guest. When I do, I make a connection with no problem, but after the initial page comes up, additional pages load very, very slowly regardless of what browser I use (Chrome, Firefox, or IE). I don't have that problem on any other network. Moreover, other users on that same hospital network can login as guests without encountering that problem. So, the problem is not browser-related, and it occurs only when a single laptop connects to a specific network. I'm using a Dell XPS 16, running Windows 7 Pro with Windows Firewall.
I have a HG-521 router which is syncing at 8724kbps, but it is slow loading pages. My isp is talktalk .
Tech Support Guy System Info Utility version 220.127.116.11 OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit Processor: Genuine Intel(R) CPU 575 @ 2.00GHz, x64 Family 6 Model 15 Stepping 13 Processor Count: 1 RAM: 3063 Mb Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 2 Mb Hard Drives: C: Total - 114370 MB, Free - 56821 MB; E: Total - 99 MB, Free - 61 MB; Motherboard: ASUSTeK Computer Inc., X58L Antivirus: avast! Antivirus, Updated and Enabled
I'm performing a migration from an ASA5520 running version 8.04 to an ASA5525-X running 8.6.
The issue I had was that whilst all of the SSL VPN portal configuration was migrated the initial portal page does does not load. I thought that this could be to do with ASDM and WebVPN both being enabled on the outside interface and so I tried changing the port used for ASDM and disabled the ASDM altogether on the outside - but still to no avail.
Could this have something to do with the fact that you can no longer just point your browser at the outside interface of the firewall to get to the ADSM? Does some configuration need to change for the ASA to accept connections on the outside interface?
The basic WebVPN access as it stands right now is:
It's' my first router (E 2500) one desk top and two laptop and also a Ipad connected, every thing look fine exept for the Ipad.Lots of page not fully loading, I have to reload couples of time to get it full load. and lots of Youtube video said not presently availale but work fine with laptop or desktop.Did not change any seting on the router, I just plug it and used it
Just purchased a SG300-52 and am trying to upgrade the firmware to 1.1.2 but cannot get the Upgrade/Backup Firmware Language page to load in the web browser interface. I have tried IE 8 and 9, Firefox 3.16 and 10.02, and Chrome from Windows 7 and XP Pro systems also tried FF and Chrome from Ubuntu system. The page just never loads - doesn't show anything.The same is true of the Download/Backup/Configuration/Log page. The other links under Administration > File Management seem to work fine.
I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.
I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.
The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.
I have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.
I'm having issues accessing facebook from my system, it worked untill a few days back where its not opening and gives a message "The connection to the website was reset". I have tried every trick in the book. I'm on Windows XP Pro.
1. I tried accessing the site from IE6 opera and mozilla still no luck.
2. I disabled my firewall and antivirus
3. Zonal Alarm and avira
4. I also uninstalled both and tried nothing worked.
5. Im able to ping the site and also did a tracert.I also flushed the dns and winsock.
I have a different problem, after i succesfully erased the spyware protection virus, i cant get in the internet anymore :( it always says "the connection was rest" on firefox and it wont load any site in IE either. what to do
I am configuring Clientless SSL VPN on ASA5505 with 8.2(2)17. After the login, default page should be "Home", but if activating "Anyconnect". it always goes to Anyconnect as a first page. If disabling "Anyconnect" using SSL VPN Customization Editor --> Portal --> Application, it always goes to the other one. Never get "Home" as a first page, can I set the first page manually?
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone -HP Mediasmart Windows Home Server -Desktop -Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP 2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
I've had two 932Ls for a year and they work fine. Both installed trouble-free and have been used with motion-detection wirelessly. I often go straight to their local IPs in my browser to make any changes to settings etc (avoiding myDlink). I just bought two 930Ls (don't need/want the IR-function on these) and tried to install them. Process went seemingly smooth but once the camera was installed and wireless, problems started to crop up. As I saved settings in the web interface, I would get 404 "page not found" errors. Refreshing would make it work again...sometimes. More often than not, I cannot reach it through the web interface and the camera reads "disconnected" in D-ViewCam. It usually works on myDlink though. i've checked all the network and wireless settings and they are identical to my 932Ls. The connection is just unstable for some reason. The problems are apparent in the web interface and D-ViewCam which also means I can't trust the motion detection and emailing function. It is also NOT visible in my Windows 7 network environment, whereas the two 932Ls (and my entire Sonos network) do show up there.The 930L is running firmware 1.04 and the 932Ls are running 1.02. I know there is a 1.06 available but before I try that I'd like to get your views on this problem. Could it be a faulty unit? I don't want to fight through this problems - if it persists I'd rather return the cameras and buy two more expensive 932Ls and just turn off the IR in the interface. Or is this a known issue with the 1.04 firmware?
Even writing this right now, the camera suddenly popped back up on the web interface inexplicably, without me doing anything. and back up on D-View Main Console.
I was trying to set up an ad hoc network and toyed around with some of the wireless network settings. The network I was trying to set up didn't quite work out so I tried to set it back to how they were but forgot how they were. Is there a way to delete the Wireless Network Connection and let it create a new one or is there a "standard" setting for this to strictly find a wireless network and connect to it?
We have a site to site VPN tunnel that consists off a Cisco 877 at a remote site and a Cisco ASA5510 at the Head Office.
Remote Site 192.168.100.0/24 > Head Office 192.168.0.0/24
telnet 192.168.0.36 25 works telnet 192.168.0.34 443 works telnet 192.168.0.202 21050 fails ping 192.168.0.202 works
The VPN tunnel is working in No NAT mode and allows IP any from each subnet. AD replication works fine across the VPN tunnel and so does telnet from the remote subnet to an exchange/web server at the Head Office.
The device on 192.168.0.202 is listening on the required port as we can telnet to it locally. The device does have a different gateway, but a route statement is in place to use 192.168.0.2 as it's default gateway for 192.168.100.0/24 traffic.
What doesn’t work is a connection to the phone system, we get the following in the logs:
6 Jun 09 2011 22:20:20 302013 192.168.100.1 60759 192.168.0.202 21050 Built inbound TCP connection 5799085 for outside:192.168.100.1/60759 (192.168.100.1/60759) to inside:192.168.0.202/21050
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
I have a pair of ASA 5550s running Anyconnect Essentials, with multiple connection profiles configured. I would like the login page to the portal to default to our main corporate profile (so the users get NAM and all the policy goodness), but presently it is defaulting to the last profile I created. Is there any way to modify the default connection profile in the drop down list so it always defaults to my preferred profile? It seems like I saw this sometime in the past.
normally insert the D-link CD in my computer and then follow the steps. this time in the step that all connectivity was being checked the message appeared that one of the cables (ethernet or the other one) is not connected whereas I am quite sure that they are properly connected and nothing at least as far as I know is wrong.after several times, I could connect to the wirelss connection but actually there was no internetwhen I also tried with cable directly from wall jack to my computer it was also the same case.
I just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
Ok starting about an hour ago I seem to be having a problem accessing youtube as well as Facebook & now Microsoft?I have done some searching around and tried a few of the suggestions I found including; trying another browser (happens using both Mozilla and IE), clearing internet cache, unplugging my modem for a minute then plugging it back in, etc, and so far none of these have worked. I did get youtube to work once since then long enough to upload a 10 sec video but once it was uploaded and I tried editing the video details I once again found myself taken to the page that says The connection was reset.
I have been having this problem randomly on and off the last week or so. If I type facebook in any of my browsers it comes back with the connection has been reset. If I use hidemyass I can get onto facebook though. My partner is having the same problem. I haven't got a firewall blocking facebook and it works sometimes and other times it doesn't so I am unsure what the problem is.
Ever since setting up this router it has been giving me problems on my laptop, connected wirelessly. At random intervals, throughout the house, an error saying "Connection was reset" comes up in firefox when browsing the web. I've tried resetting the router twice, and updating my network adapter's(Intel 465AGN) drivers. Neither of these worked. No settings on the router were modified, other than enabling the Qos engine. Signal quality isn't the problem either as it is full at all times. On my other computers, three connected through wireless and one through wired, there have been no problems at all and they perform very well.
Just bought myself an ASA5505 to replace a PIX 501, and having transferred over most of the previous config I've managed to get the two IPSEC VPN tunnels working as before.
Unfortunately when I try and SSH to the ASA the connection just resets instantly even when the tunnel is up. It seems as if the ASA is actively refusing the connection, though the log doesn't state this. I had always presumed that traffic over an established IPSEC tunnel was implicitly trusted and not subject to usual access-list rules.
I am unable to SSH to the ASA from the 10.0.0.x range, but I can SSH to a machine on 10.27.0.4 (so I know the tunnel is up and working)
Config (minus irrelevant sensitive information) is attached for reference.
Also - though I'm not sure how relevant it is given the tunnels appear to work - when I enter the line "crypto map meepnet-map interface outside" in config mode the ASA reports "WARNING: The crypto map entry is incomplete!" even though I have supplied the access-list, peer and transform-set variables.
since last nite my router E1200 has been having speed up and down problems.first it goes to 150mb/s then back down to 1 for a few minutes, usualy its stuck at 72mb/s which is a far cry from its rated 300mbps but qi'd rahter have that than 1-2mbps.i'd be happy with 150mbps but that only lasts 5mins then goes down to 1-2mbps and i have to reset my connection.
I have a Linksys WRT54GS (v5) router. I noticed that my firmware was outdated and tried to upgrade it tonight. During the upgrade progress, the browser reset the connection and now cannot access my router configuration pages.I did a hard reset. Then I did the 30-30-30 reset.
The reset worked but no matter what I do, I cannot navigate to any readable page within the router. I get the log in box and successfully log into the router. However, the configuration page(s) are all jumbled and devoid of useful information. It almost looks like a web page that needs flash to be enabled. Lots of colors and boxes but no text or links to other configuration pages
I know it's an old router but it has served me well. I would love to reinstall the old firmware (or new!) and copy my saved configuration file back to the router.Is there a way to access the configuration via a command line interface?