The Connection Was Reset Error When Attempting To Load Certain Sites?
Apr 11, 2011
Ok starting about an hour ago I seem to be having a problem accessing youtube as well as Facebook & now Microsoft?I have done some searching around and tried a few of the suggestions I found including; trying another browser (happens using both Mozilla and IE), clearing internet cache, unplugging my modem for a minute then plugging it back in, etc, and so far none of these have worked. I did get youtube to work once since then long enough to upload a 10 sec video but once it was uploaded and I tried editing the video details I once again found myself taken to the page that says The connection was reset.
View 3 Replies
ADVERTISEMENT
May 26, 2012
So i just brought my computer home from my dorm where it was working fine. as it is in my rom now I bought the XAVB1004 from netgear to connect it from my room t the router in the computer room. That device works great as I have tried my laptop with it and it works. I can connect to the internet as i have set u my router on my computer( the one that i took from my dorm) but only google loads, i can also search in google, and youtube loads where i can oddly watch videos no problem. I have tried reinstalling my ethernet drivers, winsock reset, checking/unchecking just about every setting in internet options and so on. No browser seems to work and I am out of ideas. I turned firewall off as well to no prevail. I have no clue where to look next as 3 days ago my computer worked fine and all I did now was move it.
View 7 Replies
View Related
Mar 28, 2011
I have a different problem, after i succesfully erased the spyware protection virus, i cant get in the internet anymore :( it always says "the connection was rest" on firefox and it wont load any site in IE either. what to do
View 1 Replies
View Related
May 11, 2010
Ever since setting up this router it has been giving me problems on my laptop, connected wirelessly. At random intervals, throughout the house, an error saying "Connection was reset" comes up in firefox when browsing the web. I've tried resetting the router twice, and updating my network adapter's(Intel 465AGN) drivers. Neither of these worked. No settings on the router were modified, other than enabling the Qos engine. Signal quality isn't the problem either as it is full at all times. On my other computers, three connected through wireless and one through wired, there have been no problems at all and they perform very well.
View 2 Replies
View Related
Sep 13, 2011
I an currently running Cisco (ACS 5.2.0.26.3) and attempting to get my Cisco 5508 WLC's (7.0.98.0) loaded into ACS for TACACS+ authentication for managment users.
However I keep getting the following error:
*emWeb: Sep 14 14:44:45.931: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed for the user:test_tac. Service-Type is not present or it doesn't allow READ/WRITE permission.
Now I've attempted the step-by-step using the following URL but to no avail.( there are some slight differences in ACS 5.2)
[URL]
Latest WLC configuration guide I could find (Software Release 7.0 June 2010) isn't much useful either.
View 6 Replies
View Related
Mar 13, 2011
Getting error message W016.15ISP when attempting to make wifi calls on my T-Mobile myTouch 4g cellphone. I currently have internet service with Charter which uses a cable modem/router.
View 1 Replies
View Related
Oct 26, 2012
Certain sites on my desktop will not load. These sites include speedtest.net, twitter, battle.net ect. Youtube opens, but videos don't play. However some work fine, such as reddit.However, my connection is fine on my laptop. My laptop is wireless and my desktop is wireless.I recently got my desktop back from repairs, and it has a new motherboard, with a clean instal of windows vista. I installed all the drivers ect. It says im connected to the internet, and I can access some sites. I've flushed the DNS, and called my provider. They say nothing is wrong on their end.Oh, and after ringing the repair shop, they said to install adobe and java. Java installed fine, but the adobe site wouldn't load (lol). So I copied the adobe files from my laptop over to the desktop. Youtube videos now play, but it feels slow, considering im on a 30MB download connection.
View 3 Replies
View Related
Dec 18, 2011
I have a problem on my Google Chrome explorer that if for example I am going to [URL] so every time I am clicking in a link (no matter what... some friend's profile, or friend's pictures...) I see only the blue Facebook bar on top and that it. So if I want to page to load perfectly I need to mark the address and click enter, and then the page loads perfectly.
An I need to do this any time I am entering any link. And it's not only on this site. it's also some others sites includes Twitter.
I tried to see if the problem continues in other explorer like firefox and IE, but not... it works perfectly there!
View 3 Replies
View Related
Jan 14, 2011
I have today the issue that I am unable to load certain websites, I can enter but whenever I click on continue to navigate in that same site for example FACEBOOK, I see the operation just loads and dont go anywhere, after that remains in same condition unless I cancel or close the browser.I checked the firewall, and also the antivirus, but nothing seems wrong, I can get in into HOTMAIL, GOOGLE, but again certain sites if I search something on GOOGLE, get frozen again .
View 1 Replies
View Related
Jan 7, 2011
I am having trouble with my wireless connection. I am only able to visit websites but if I try to use the internet for anything else (AIM, Yahoo instant messenger, etc), it will not work. This is not a modem issue because my other computers' connections still work fine.
Configuration Host Name . . . . . . . . . . . . : JingJunBusiness
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
View 1 Replies
View Related
May 9, 2011
About a week ago my mom (unknowingly to me) installed a registry "booster" (Uniblue Registry Booster) and as expected, it messed some stuff up. As soon as she finished scanning and it "fixed" all her registry issues, she could no longer load webpages in her browser.PC was running XP at the time of the corruption, none of her system restore points work, and unfortunately her automatic backups had stopped running about 2 months ago without me knowing. She's been planning to switch to Windows 7 soon anyway so after a few days of trying to find a solution and not having any luck I thought "well maybe if we upgrade it will unintentionally fix some files / settings during the install." Going from XP to Windows 7 was no fun task itself, but after many hours of installs I had it upgraded to Vista and then to 7.
View 15 Replies
View Related
Dec 19, 2011
Loading yahoo page on windows 7.
View 1 Replies
View Related
Oct 12, 2012
This problem just started. I am unable to load certain https sites (for work). If i directly connect to ethernet, it works, so my isp isnt my problem. When i try to connect to the sites, it says "sending request" then times out. I have played around with the settings non stop and nothing has worked. I have a mac running 10.7.5.
View 3 Replies
View Related
Apr 30, 2011
i have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies
View Related
Mar 29, 2012
Every time I reset my 1841 router the startup configs don't load. Its acting like a password recovery process has started. I can't figure out why its doing it,
View 2 Replies
View Related
Apr 3, 2011
My computer had a filter on it that used a proxy server. The company (called Familink) went out of business. They provided an application for removing the filter, but it did not work, and the filter was never removed. I believe when the filter was installed, it modified the registry to prevent internet browsing unless the proxy was active. Now, since the company is out of business, there is no way to use the proxy, and I cannot browse the internet at all. I can still connect to secure (https://) sites just fine, but not any other channel. It is not a problem with the ISP, because I can browse the internet just fine on the same computer using linux. It just does not work with windows. When running a diagnostic test, I get error 0x2751, or "WSAEHOSTUNREACH"
View 3 Replies
View Related
Sep 12, 2011
Having being able to get a basic Ipsec VPN (with userid/password) connection to work between my Cisco ASA5505 and iPad over the Internet, I now am trying to introduce a digital certificate in the authentication VPN mechanism. However, I am getting an "Error processing payload: Payload ID: 1" , as seen on the Real time log viewer of my ASDM 6.2.This is what I did on the 5505 ASA to create a digital certificate:-
1) go to Configuration -> Remote Access VPN -> Network (Client) Access -> IPsec Connection Profiles and using the DefaultRAGroup profile I exported the Identity certificate (previously created) as PKCS12 with an appropriate passphrase/password.
2) I then created a new connection profile on the iPad using the CISCO ASA exported identity certificate. And unfortunately the connection fails, with the above message.
I would like to know if I am on the right track thinking I can use the CISCO identity certificate on the Client computer. The identity certificate is RSA 1024 bits and is self enrolled.I have not ebabled the CA Server in the Local Certificate Authority of the ASA 5505, I wonder if I have to.
View 0 Replies
View Related
Jan 21, 2011
For a few days now, my internet has been as the title suggests. A speed test has shown my download and upload speeds to be about 0.06 mbps each. Every once in a while, I try a diagnose and repair, and occasionally I get one of either "Reset your TCP/IP settings" or "Improve your TCP/IP performance", but neither works. I've tried resetting my modem and have done a system restore to no avail. Offline performance is good, RAM is in good shape, etc. AVG hasn't found any viruses or spyware. It's an ethernet cable, by the way.
View 11 Replies
View Related
Aug 16, 2012
when load MIB file have error unable to load the MIB file Error: can't find RFC1155-SMI.I can not find RFC1155-SMI.my Where I can find or download RFC1155-SMI.my.
View 5 Replies
View Related
May 7, 2012
I have a Cisco 1841 router connected to two different lines (same ISP) and I would like to load balance between them. I think I have achieved this point, but the problem is that remote VPNs do not work (only from Dialer1).This is my diagram:
ISP1----ISP Router----------Fa0/1 ROUTER 1841
----------Fa0/0 LAN
ISP2 ----------------pppoe Dialer1 ROUTER 1841
I have tried to redirect all my vpn traffic through the Dialer1 with PBR, but it does not work.
View 4 Replies
View Related
Jan 15, 2012
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
View 3 Replies
View Related
Jul 8, 2012
MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 1.1.1.1 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.
View 2 Replies
View Related
Apr 28, 2011
Is it possible to connect two distant sites e.g. 30 miles wirelessly? Will there be any issues with Line of sight and interference? Will it be a better solution compared to that of wired counterpart?
View 3 Replies
View Related
Jan 31, 2011
When I try to go to certain websites on my home PC they take up to several minutes to load. It does not matter what browser I use. When I visit the same sites from work (or any other place, literally) the sites load without delay of any kind.
View 4 Replies
View Related
Nov 26, 2012
I am currently at university, using a Local Area Connection. I am aware that the university blocks torrenting which I am totally fine with though when I try to carry out a process such as posting a large entry on Livejournal.com or Dreamwidth.org, it tries to load for a couple seconds and then fails. When in Google Chrome, it says that it's "uploaded 100%" but then I receive "Error 7 (net::ERR_TIMED_OUT): The operation timed out.". When using Internet Explorer, it either doesn't load at all or I get the standard "Internet Explorer cannot display the webpage". When I try to carry out a different process on dreamwidth and livejournal (editing my layout), Chrome tells me "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." These issues always happen no matter when I try them.
View 2 Replies
View Related
Feb 10, 2013
My bsnl wimax connection has stopped working on my laptop...IT WORKS ON MY FREINDS' LAPTOP. On my laptop (windows 7), in the taskbar, it shows connected and everything seems fine but i cant access any sites or download anything? Does this have to do with a bluetooth device i installed a few days back or some other issue.
View 3 Replies
View Related
Jul 11, 2011
I have been working with my ASA 5505 VPN Concentrator to maintain a connection with one of my remote sites. I have several tunnels that work fine and dont have any issues at all, but one tunnel with outside IP ending in 146 and inside LAN 192.168.3.0 goes down every 24 hours. Attached is the config from the concentrator. I changed around the Security Association Lifetime Settings and the tunnel would drop after that amount of time expired. If I set it to 24 hours, the tunnel would drop every 24 hours. If I set it to 8 hours it would go down every 8 hours.
I have swapped the router a few times, double and triple checked my key settings, disabled keep alives on both ends, and this problem just started happening a few weeks ago after working fine for years. I also get the following e-mail error every time it goes down:
<161>Jul 10 2011 16:19:47: %ASA-1-713900: Group = xxx.xxx.xxx.146, IP = xxx.xxx.xxx.146, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
View 6 Replies
View Related
May 4, 2011
I'm trying to set up a website filter on my DIR-601. I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging. Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites". When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.") However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received. Unable to load the webpage because the server sent no data." This happens with ALL non-blocked websites. I'm using hardware version A1, firmware version 1.01NA.
View 2 Replies
View Related
Jun 4, 2012
My laptop was connecting fine to a Liknsys G router until one day it couldn't connect because it gets stuck to Attempting to authenticate. I have one more laptop, a desktop and an ipad and all connect fine to the network except of my laptop. I removed the network password but nothing again.
View 9 Replies
View Related
May 15, 2012
I'm working as a network engineer for a service provider, and we had just gone through a pretty large scale upgrade throughout our network and service.But not long after the upgrade (or maybe ever since the upgrade, we can't confirm this because we probably missed it out due to many other links to be tested), we met a peculiar problem.Everything seems to be running fine most of the time, but there has been some weird 'ghost-like' activity which have been causing inconsistent network disruptions. At times, certain portions of the network can't communicate with other subnets.And most obviously is the problem with a continuous ping and a traceroute simultaneously. Ping is usually normal, but until a traceroute is attempted, it times out at the same time as tracert fails to obtain the route.Besides, performing a ping from the 2nd closest hop address, 10.250.253.251, which is a cisco layer 3 switch also has problems, the results shown are as belowType escape sequence to abort[CODE]
View 1 Replies
View Related
Oct 29, 2011
So all of a sudden the trusty HP 4000 stopped printing. A little bit of troubleshooting and I found out that the problem was the JetDirect card. I purchased a new one (615n - same model as the old one), installed it, ran a printer configuration page, confirming I have an IP (192.168.x.x) and subnet mask (255.255.255.0), config by DHCP.Also, ran a ping test and it appears to be fine?
View 1 Replies
View Related
Oct 22, 2011
I tried changing my wireless settings from wpa2 to wpa, but it wouldn't allow me to connect. I made the change in settings because I read somewhere that it would allow you to connect your blackberry. I changed the wireless settings back to what they were, reset the router, but now the wireless sign doesn't even light up on my belkin router and it always says 'unable to connect to the network'. Something about 'attempting to authenticate'?
View 2 Replies
View Related
Aug 31, 2011
I'm having difficulty connecting my desktop to my wireless network. Some details to start off: I'm using a G-Sky usb wifi adapter model number GS-28usb. I recently moved from an apartment with free wifi and I set up broadband with Qwest/CenturyLink. The modem/router is an Actiontec Q1000. The firmware is up to date (I checked) and every other device I bring into the house can connect just fine (laptop, roommate's desktop and laptop, and my blackberry) I'm running Windows 7 x64 Ultimate on all machines, with all updates currently available. My network shows up in the list of available networks, signal strength fine, but when I try to connect, it does its initial "getting information..." in the small box in the corner of the screen, then the box disappears and no connection is made. The status of my adapter at that point will say "attempting to authenticate" and will remain like that even though (apparently) windows has given up on trying to connect to the network. It never gets to the point where it asks me for the passkey. I've changed just about every variable I can think of that might affect this on the router (encryption type, b/g/n, legacy mode, compatibility mode, etc, i've renamed the network, powercycled the router, etc) all to no avail. I've tried to manually add the network settings under wireless profiles, but even though the information I put in is EXACTLY correct, under available networks its says that my settings don't match those on the network. I've tried different wireless adapters, and none will connect, so I've eliminated a faulty adapter. I can connect to my laptop with an ethernet cable, and bridge the connections so I can use the internet on my desktop, but i cannot connect directly to the router.
here is my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersPancho>ipconfig/all
[Code].....
View 1 Replies
View Related
