Laptop Stuck When Attempting To Authenticate
Jun 4, 2012
My laptop was connecting fine to a Liknsys G router until one day it couldn't connect because it gets stuck to Attempting to authenticate. I have one more laptop, a desktop and an ipad and all connect fine to the network except of my laptop. I removed the network password but nothing again.
View 9 Replies
ADVERTISEMENT
Aug 31, 2011
I'm having difficulty connecting my desktop to my wireless network. Some details to start off: I'm using a G-Sky usb wifi adapter model number GS-28usb. I recently moved from an apartment with free wifi and I set up broadband with Qwest/CenturyLink. The modem/router is an Actiontec Q1000. The firmware is up to date (I checked) and every other device I bring into the house can connect just fine (laptop, roommate's desktop and laptop, and my blackberry) I'm running Windows 7 x64 Ultimate on all machines, with all updates currently available. My network shows up in the list of available networks, signal strength fine, but when I try to connect, it does its initial "getting information..." in the small box in the corner of the screen, then the box disappears and no connection is made. The status of my adapter at that point will say "attempting to authenticate" and will remain like that even though (apparently) windows has given up on trying to connect to the network. It never gets to the point where it asks me for the passkey. I've changed just about every variable I can think of that might affect this on the router (encryption type, b/g/n, legacy mode, compatibility mode, etc, i've renamed the network, powercycled the router, etc) all to no avail. I've tried to manually add the network settings under wireless profiles, but even though the information I put in is EXACTLY correct, under available networks its says that my settings don't match those on the network. I've tried different wireless adapters, and none will connect, so I've eliminated a faulty adapter. I can connect to my laptop with an ethernet cable, and bridge the connections so I can use the internet on my desktop, but i cannot connect directly to the router.
here is my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersPancho>ipconfig/all
[Code].....
View 1 Replies
View Related
Jul 29, 2012
I can not connect to my wireless network from my pc. My laptop is fine. the internet worked like 5 times.. but it's been dead for two days now and everything I try seems to fail.i can see my router in connections, (sometimes not) And when i see it, it says limited acess and works for like10 mins..The OS is Windows 7 ultimate 64bit and im using a gigabyte GN-WB01GS USB WLAN card#2 network adapter. The signal strength is good. Ran all the windows trouble shooters... nothing, though it works wired. After clicking connect im told that it is attempting to authenticate forever and that is all that happens,I dont get why it works sometimes, then doesn't.when the internet works it have worked like 5 times (for 10 minutes) but now i cant even connect to it..Whenever i tried to download SOMETHING, it stopped working. And the internet i had those 5 times was were slow, not 54 mbit net. [code]
View 14 Replies
View Related
Oct 22, 2011
I tried changing my wireless settings from wpa2 to wpa, but it wouldn't allow me to connect. I made the change in settings because I read somewhere that it would allow you to connect your blackberry. I changed the wireless settings back to what they were, reset the router, but now the wireless sign doesn't even light up on my belkin router and it always says 'unable to connect to the network'. Something about 'attempting to authenticate'?
View 2 Replies
View Related
May 3, 2011
I have been trying to re-establish my wi-fi connection for over a day now. I have a Dell Inspiron 1545 with windows 7 and it has two wifi adapters, one is the 1397wlan and the other is a virtual miniport adapter. My carrier is at&t uverse/2wire and my service was disconnected for about eight or nine days and since then I cannot get my wi-fi back. The desktop computer works fine but my network adapters are showing attempting to authenticate and not connected for the miniport adapter. I have tried enable/disable, restoring to a previous date, ipconfig/release, and of course running the trouble shooter for Microsoft. The result is that they can't assist with my connectivity issue and that its either the adapter or my router. I can use the laptop with the ethernet cord but its not practical as the router is downstairs and I primarily work upstairs.
View 2 Replies
View Related
Sep 13, 2011
I an currently running Cisco (ACS 5.2.0.26.3) and attempting to get my Cisco 5508 WLC's (7.0.98.0) loaded into ACS for TACACS+ authentication for managment users.
However I keep getting the following error:
*emWeb: Sep 14 14:44:45.931: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed for the user:test_tac. Service-Type is not present or it doesn't allow READ/WRITE permission.
Now I've attempted the step-by-step using the following URL but to no avail.( there are some slight differences in ACS 5.2)
[URL]
Latest WLC configuration guide I could find (Software Release 7.0 June 2010) isn't much useful either.
View 6 Replies
View Related
Mar 22, 2011
I'm at my girlfriend's house and every laptop in the house works beside hers! I tried mine and it connects flawlessly also my itouch and my eee-pc also connect without any trouble but her laptop is stuck on Identifying i tried the whole netsh reset thing and sadly we cannot have access to her router as her dad hates it when we play in his Linux based stuff anyways any simple fix would be welcome, i hope no one will suggest changing routers/reinstalling the whole OS[CODE]
View 5 Replies
View Related
Oct 19, 2012
The wireless router PW has been changed, I got the new one correct but upon entering it on my laptop it goes around circle showing,"Wireless network detected" and then,"Unable to connect to preferred wireless network"It never works. I don't know how to fix this problem. It did not happen on my iPad.
View 2 Replies
View Related
May 15, 2012
I'm working as a network engineer for a service provider, and we had just gone through a pretty large scale upgrade throughout our network and service.But not long after the upgrade (or maybe ever since the upgrade, we can't confirm this because we probably missed it out due to many other links to be tested), we met a peculiar problem.Everything seems to be running fine most of the time, but there has been some weird 'ghost-like' activity which have been causing inconsistent network disruptions. At times, certain portions of the network can't communicate with other subnets.And most obviously is the problem with a continuous ping and a traceroute simultaneously. Ping is usually normal, but until a traceroute is attempted, it times out at the same time as tracert fails to obtain the route.Besides, performing a ping from the 2nd closest hop address, 10.250.253.251, which is a cisco layer 3 switch also has problems, the results shown are as belowType escape sequence to abort[CODE]
View 1 Replies
View Related
Oct 29, 2011
So all of a sudden the trusty HP 4000 stopped printing. A little bit of troubleshooting and I found out that the problem was the JetDirect card. I purchased a new one (615n - same model as the old one), installed it, ran a printer configuration page, confirming I have an IP (192.168.x.x) and subnet mask (255.255.255.0), config by DHCP.Also, ran a ping test and it appears to be fine?
View 1 Replies
View Related
Apr 11, 2011
Ok starting about an hour ago I seem to be having a problem accessing youtube as well as Facebook & now Microsoft?I have done some searching around and tried a few of the suggestions I found including; trying another browser (happens using both Mozilla and IE), clearing internet cache, unplugging my modem for a minute then plugging it back in, etc, and so far none of these have worked. I did get youtube to work once since then long enough to upload a 10 sec video but once it was uploaded and I tried editing the video details I once again found myself taken to the page that says The connection was reset.
View 3 Replies
View Related
Jan 22, 2011
i have a DIR-601. Basic settings, port forwarded for Xbox live and Wolfenstein enemy territory.I have a home PC with a wired connection and a laptop which is set up through wireless. I installed the game Wolfenstein: Enemy Territory on my laptop and every time I start the game and attempt to fetch a server list, my router resets itself. The game works fine when I connect directly to my modem, but not when I connect to my router
View 1 Replies
View Related
Jan 23, 2013
I am attempting to set up snmp v3 monitoring of my 2900 series routers from the third party Spiceworks utility. My snmp config on the router looks like this:
SNMP-Server view Westv3View internet included
SNMP-Server group Westv3Group v3 priv Read Westv3View
SNMP-Server user Westv3User Westv3Group v3 auth MD5 <password1> priv DES
[Code]....
I have set the logging level on the 2900 router to informational and see no errors of any kind popping up when I try to scan the router from SpiceWorks. Spiceworks just returns a generic "unable to contact host" message.
View 2 Replies
View Related
Dec 22, 2012
I am attempting to connect a video streaming device to my wireless network and it will not accept what I think is the password
View 1 Replies
View Related
Aug 1, 2011
I keep getting this error every few days and I have to restart my router in order to gain access back to the web utility. I reflashed the fw a second time with no success. I have read about this trip 30 reset but have had no luck finding a post which describes how to go about that method.
View 5 Replies
View Related
Jul 28, 2011
I upgraded the IOS on my 887VA router which is not yet in service. The next day I did a cold boot and made some changes. Then, when I wrote them this warning popped up which seems to imply I need to recreate my configuration from scratch in order to avoid potential issues.Is that the correct interpretation of this message/scenario? [code]
View 2 Replies
View Related
Nov 7, 2012
I have an ASA pair configured to replace a router that hosts a collection of IPSec Tunnels. Tunnels appear to work. I am lab'ing some additional controls that I would like to implement. On the Production Router that i plan to replace with the ASA's the current Tunnels are all wide open (all traffic allowed to pass). I was hoping to lock things down a little without having to reconfigure all of the Tunnels. My though was that an ACL on the Inside Interface blocking selected traffic Out (so into the LAN) should not impact the stability of the Tunnels but allow me to restrict some traffic from entering the LAN. One port that I was attempting to block is RDP 3389. When this ACL is applied to the inside interface it does not block Port 3389 at all. What am I missing? Is it that the trffic is being allowed because it is coming through one of my 'open' Tunnels?
Shouldn't IPSec Tunnel traffic be processed by the Inside Interface ACL just like all other traffic?
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 3389
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 135
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 137
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 138
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 139
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 445
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 389
access-list 145 permit ip any any
ip access-group 145 out interface Internal
This work great on a 2821 Router, but not so much on the ASA.
View 11 Replies
View Related
Jun 21, 2011
I have a Zoom adsl x6 model 5590 wireless router. I recently tried to update its firmware by following the instructions from the manufacturers site. Everything seemed to go correctly, but I am now unable to connect to the internet or my routers http address. My router now has a red power light along with a solid green light for the wlan and dsl.
View 2 Replies
View Related
Mar 13, 2011
Getting error message W016.15ISP when attempting to make wifi calls on my T-Mobile myTouch 4g cellphone. I currently have internet service with Charter which uses a cable modem/router.
View 1 Replies
View Related
Mar 17, 2011
We replaced a WLC2106 with a WLC2112 and the 2112 can't authenticate anything. Both WLCs have the exact same configuration on them. We are using a RADIUS server to do MAC authentication. Both WLCs have been set to use no delimiter in the MAC filtering.
When the 2106 is in place, we have no issues and all allowed devices can authenticate without issue. However, when the 2106 is removed and the 2112 is powered up, every single device fails authentication and is put on the exclusion list. When we check RADIUS, it tells us the devices fail because they are locked. We unlock the device's account, and 5 minutes later the 2112 has screwed something up and they are locked again.
View 3 Replies
View Related
Aug 20, 2012
we have deployed L3 in-band scenario for wireless 2 years ago and the solution was working without any problem. we have upgrade wireless controller to 5508, since then, when users login to the first page and certified, and they want to browse to the internet, NAC redirects the web page and ask for authenticatin again, despite the users' devices are being shown as certified devices in the list.
View 6 Replies
View Related
Aug 30, 2012
Having an issue with Macbook authentication. All Macbooks at this one site, on same switch, going to same RADIUS server, work except for one. Looking at logs it appears server and client never exchange certificates. Attached is log for failed Macbook authentication.
View 4 Replies
View Related
Jan 30, 2013
I have been trying to set this up for like 4 hours. What a waste of time. This should be as easy as punching in the IP and password for the radius server. It isn't.I have a brand new SG-300-10. LATEST firmwawre, I just updated it about 5 minutes ago. 1.2.7.6 I think.This is what I have done so far in the GUI: (I have CLI access too if necessary)
Security > RADIUS and entered my radius IP/secret there.
Security > Access Management Profiles > Create new template called ALL that permits access to all applications. Set it as active also.
Security > Management Access Authentication > For HTTP and SSH
I put RADIUS first then Local second.My radius server works. As I type this message I am logging in via radius with OpenBSD/Centos even Fedora. (If OpenBSD can do it, these switches can do it.)But whenever I try to login with RADIUS credentials to my switch, I get no logs or any connectivity reports on my radius server? Is the switch even attempting to contact the server? The logs dont show anything regarding RADIUS. I am trying a reboot now, but I don't think that should be necessary.Is there a step I missed? When first looking at this I expected it to be done in 5 minutes. I have been on this for lik 4 hours. Isimply want to login to the administration console (web gui) using RADIUS credentials.
View 5 Replies
View Related
May 24, 2011
I think i've got everything set up to authenticate against AD for Tacacs+ device logins. When i check the logs, i see:"24408 User authentication against Active Directory failed since user has entered the wrong password". This leads me to believe that it is checking AD correctly, however if i enter the password correctly for the same AD user, there is no log at all...no pass, no fail.
If i look at the Tacacs debugs on the switch, i see the following:May 25 10:55:07.927 CDT: TAC+: ver=192 id=874699084 received AUTHEN status = ERRORMay 25 10:55:09.932 CDT: TAC+: send abort reason=Unknown
Obviously the switch is communicating to ACS, and ACS is passing info back to the switch. ACS also appears to be communicating effectively with AD since it knows when i put in an incorrect password for the specific user.
View 2 Replies
View Related
Feb 14, 2012
I am trying to connect using officeextend but couldn't . I have managed to connect the officeextend AP to the DMZ WLC however i cant get the users to authenticte to the ACS (although there is a rule to access the access on ports 1813 and 1812). Should the DMZ WLC need the ACS servers (i thought they wouldnt require as they are anchored back to the Internal WLC that the ACS server address
oon a side note, i have'nt created dhcp for hte officeedxtend users - will this cause an issue - (just deciding on to it on WLC or windows server)In-fact i cant even see myself authenticating on the ACS server
View 25 Replies
View Related
Mar 16, 2012
I work at a public library, and our wireless network is controlled with a captive portal. I am using the app Tasker on my Verizon Galaxy Nexus (Android 4.0.3) to do things like automatically silence the phone when it connects to the wireless network. What I'm hoping to do is get it to also automatically authenticate with the captive portal. I know this is possible on a PC, but I'm not sure how to implement it with my phone. Takser allows for using HTTP GET of HTTP POST. With GET I have fields for "Server:Port", "Path", "Attributes", "Timeout", "Mime Type", and "Output File". For POST I have "Server:Port", "Path", "Data", "Timeout", "Content Type", and "Output File". Here is documentation about these two methods:
Quote:HTTP Get Send an HTTP GET request to a webserver.The response code is stored in %HTTPR. A response code of -1 indicates a problem making the request. Any returned data is stored in the variable %HTTPD if the content type is text-based (max 4K).
Example: running a script
Server:Port: [URL] [no port specified, use port 80]
Path: cgi-bin/palpable.pl
Attributes: [must be separated by newlines, no spaces please]
colour=pink
scent=rosy
[code]....
View 17 Replies
View Related
Feb 9, 2012
We have remote users that dial-in over ISDN to a Cisco 2911. We have configured AAA to pass the authentication off to a RADIUS server. Once successfully authenticated, the router permits the users to access a single web server. However, we need to do some testing in our test environment, but unfortunately we don't have an ISDN line to test with. We have created a little environment in our LAB using a 2911, a switch, a RADIUS server & web server. I was hoping that we could simply create a "user" VLAN off the back of the 2911 to simulate our remote users, and access the web site from the test usr PC's over the LAN. I was hoping that the 2911 would be able to intercept the connection and pass the authentication off to the RADIUS server (as it does with the PPP ISDN traffic). But I cannot find anyway to do this, because I can only configure AAA to offload either PPP traffic or telnet/ssh connections to the router itself.
In summary what I want is for a user to access an internal web site over a LAN interface of a 2911 - but have the 2911 authenticate the user via a remote RADIUS server first. Is there a way to configure a 2911 (or any router!) to do this?Is the answer to configure port-based authentication (802.1X) on the switch?
View 3 Replies
View Related
Feb 24, 2013
We are running Cisco Secure ACS for Windows version 4.1(1)b23p5 on a Windows 2000 member server. Starting from today, ACS fails to authenticate users. Using the same external user (andrea-meconi) I can verify successfull and failed authentication. This is the AUTH.log for a genericRADIUS request...
AUTH 25/02/2013 15:30:24 I 0396 3900 External DB [NTAuthenDLL.dll]: Starting authentication for user [andrea-meconi]
AUTH 25/02/2013 15:30:24 I 0396 3900 External DB [NTAuthenDLL.dll]: Attempting
[Code].....
View 1 Replies
View Related
Jul 30, 2012
I have setup Cisco Identity Service Engine (1.1.1) with Wireless LAN Controller (7.2.110)Everything is complete unless the URL redirect. My guest client can join the Guest SSID and also can authenticate to ISE.But after they success to authenticate with ISE, the URL in the browser doesn't change to the pre-configure. It still be something like [URL]. Anyway the content in the browser is changed to the URL that being configured such as url...How can I do with this situation cause everything is working fine but only the browser URL that is not change to the preconfigure one.
View 5 Replies
View Related
Apr 12, 2013
I have 1142 with W7 (c1140-k9w7-mx.152-2.JB)I have it configured WPA2+AES on the 2.4GHZ interface (Config below)I have my PC and Mac and phoens connected, all good.However I also have a Wi-Fi radio (url...), when I try to connect the radio to the wireless net, I keep authentication failed.If I configure my old Linksys router as the network, also using WPA2/AES, all works.Just something do to with Cisco pass and this radio.I tried TKIP > same but when I tried Tried WEP > working good!.
[code]....
View 21 Replies
View Related
Sep 8, 2011
I am transitioning from RADIUS auth to local auth and i don't want to hassle everyone to change in one hit.If i can get auth requests to look in the WLC local net db first and if not found try RADIUS then this is what i am after! You can easily do it with web auth but doesnt seem so easy via WPA2 method.
View 1 Replies
View Related
Jun 3, 2012
Have set up a pair of ACS 5.3 servers and have set up device administration authentication be passed through to an RSA server via RADIUS. All works great.
What we want to do is go a step further and set the system up so that ACS Administrators also have to authenticate to the ACS system by RSA via RADIUS (the same as the Device Authentication we've set up) for ACS administration tasks.
Looking at the options available in the ACS Administration setup (administrator accounts etc) there doesn't seem to be an option to authenticate via another method apart from a local administrator account on the ACS.
Is it possible to do this?
View 1 Replies
View Related
Aug 21, 2012
I have seen couple of people with win7 cannot authenticate to ISE: 12520 EAP-TLS failed SSL/TLS handshake because the client rejected the ISE local-certificate.I've thought of this: Maybe get a 3rd party cert (go daddy) and have that installed in ISE.I know i do have to make a CSR Cert.Sign.Request that matches cn=primary.ise.mydomain, would I also need a cert for secondary?
If I use LEAP as a preferred protocol then it doesn't ask for cert and users are authenticated successfully.I know they have to say do not validate cert and all that but sometimes it doesn't popupt to them they just can't get on.Again maybe going wtih 3rd party certs will make it easier while benefiting from using PEAP?
View 5 Replies
View Related