I keep getting this error every few days and I have to restart my router in order to gain access back to the web utility. I reflashed the fw a second time with no success. I have read about this trip 30 reset but have had no luck finding a post which describes how to go about that method.
View 5 RepliesIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : Virgin Media
Bought recently and I'm very pleased with Setup and Performance.
However, even though I have tried repeatedly with different user details and passwords I cant access the router Config without resetting to defaults using the pin in the back and admin admin.
I am using W7 and get to a log in screen via Control Panel / ... Network Sharing Centre / Network Map and see Router. Click on this and up comes a User Name and Pasword form but it never works with what I entered for the router.
i have a DIR-601. Basic settings, port forwarded for Xbox live and Wolfenstein enemy territory.I have a home PC with a wired connection and a laptop which is set up through wireless. I installed the game Wolfenstein: Enemy Territory on my laptop and every time I start the game and attempt to fetch a server list, my router resets itself. The game works fine when I connect directly to my modem, but not when I connect to my router
View 1 Replies View RelatedI have a series of problems I think are due to my 310N. First, with Facebook, I will suddenly be redirected to a248.e.akamai.net., which Chrome flags as an SSL error. Second, with (and only with) NYTimes.com, I will get "file not found" (and no numerical error) when trying to retrieve an article (via Chrome). AND, again only with NYTimes.com, I will get high-bit ascii characters in headlines. For other sites, I will get "invalid url" messages on web pages. If I unplug the modem and let it rest for 30 seconds, that seems to solve the problem. I have to do this at least once a day.
More than once a day. I don't think it's a 310N problem; but I've asked about this on other forums and got no useful reply. Previously I had similar problems with my 160 router. So, it's not the router. HOWEVER, shutting it off works with lot of the problems. Right now, after shutting off the router and turning it back on, now Facebook just doesn't come up at all. No error, just don't come up. I can ping it.
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies View RelatedI have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies View RelatedNew computer (Win7 desktop), works OK. Router is Linksys 310N. But, there are constant problems with "invalid URL" message. I was told a while back to hard code my DNS settings into the connection. That seemed OK, but last night, again got "invalid URL message" so I went back to getting DNS servers automatically. (what prompted the change was that I couldn't get to washingtpost.com). So, today I'm on NYTimes.com and everything is OK but when I try to access two pages (Op-Ed) I get "file not found". (IT was originally two pages and now it's many more.) I've had people look at the output from IPCONFIG /ALL; but any pointers, tips, etc. This seems limited to my desktop computer; the laptop on the same router is OK (also Win7).
View 11 Replies View RelatedThe router(Cisco 857) appears to be boot, and operate normally.I have tried formating the flash, re-downloading and FTP uploading the image, and also tried the latest image c850-advsecurityk9-mz.124-15.T17.bin, but this warning message persists. [code]
View 3 Replies View Relatedwant to be able to change LAN IPs on the fly for telneting into different equipment
View 1 Replies View RelatedSince i upgraded to the latest firmware my WAG160N reboots, the same as others that i read here in the forum, now i need to revert to the old firmware but sadly when i check the File is not Found. Please, re upload the old firmware.
View 1 Replies View RelatedI have successfully installed the 5.0.21.9 patch and ADE-OS 1.2 update but when I attempt the 5.1 install via "app install ACS_5.1.0.44.tar.gz local" I get the error "Manifest file not found in the bundle."
Here is a debug of the install:
HOST/admin# app install ACS_5.1.0.44.tar.gz local Do you want to save the current configuration ? (yes/no) [yes] ? Generating configuration...Saved the running configuration to startup successfully6 [30662]: application:install cars_install.c[195]
[Code].....
I created the repository by TFTPing the file to disk:/Upgrade and pointing a repository to disk:/Upgrade. I verified the checksum of the file as it sits on my TFTP server and also manually extracted the file to verify the manifest.xml file is actually there.
I can not connect to my wireless network from my pc. My laptop is fine. the internet worked like 5 times.. but it's been dead for two days now and everything I try seems to fail.i can see my router in connections, (sometimes not) And when i see it, it says limited acess and works for like10 mins..The OS is Windows 7 ultimate 64bit and im using a gigabyte GN-WB01GS USB WLAN card#2 network adapter. The signal strength is good. Ran all the windows trouble shooters... nothing, though it works wired. After clicking connect im told that it is attempting to authenticate forever and that is all that happens,I dont get why it works sometimes, then doesn't.when the internet works it have worked like 5 times (for 10 minutes) but now i cant even connect to it..Whenever i tried to download SOMETHING, it stopped working. And the internet i had those 5 times was were slow, not 54 mbit net. [code]
View 14 Replies View RelatedMy 1140 doesn't write to the config.txt file. I'm not sure why. I have three of these access points that we changed the firmware to make them autonomous. The other two worked fine.
View 1 Replies View RelatedHow can we restore ACS config from an existing backup file, in an ACS cluster deployment? is it through CLI? with"restore"or"acs restore" command? and should I restore only the ACS config or both ACS and ADE-OS config?
View 4 Replies View RelatedI uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies View RelatedI am trying to upgrade a brand new ISE 3395 from 1.0.3.337 to 1.0.4 (latest). It keeps failing with % Manifest file not found in the bundle Here is the output:
company-ise-01/admin# application upgrade ise-appbundle-1.0.4.573.i386.tar.gpg ftp
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Manifest file not found in the bundle
[code]...
I can't find anything about this for ISE, although there are a lot of topics for the same error for ACS.
I have enabled Network filtering on MAC address on my D-Link 628 router.
I've noticed entries in the log file - "Access Denied to LAN System with MAC address ______________" for 2 different MAC addresses. I do not recognize these MAC addresses. The entry that immediately follows these messages - "Above message repeated 466 times and 124 times. The entries for these 2 MAC addresses has been occurring multiple times with different repeat numbers over the past few days.
Is this an indication that someone nearby my router is attempting to hack into my wireless router or do I have a configuration issue?
I have an ASA pair configured to replace a router that hosts a collection of IPSec Tunnels. Tunnels appear to work. I am lab'ing some additional controls that I would like to implement. On the Production Router that i plan to replace with the ASA's the current Tunnels are all wide open (all traffic allowed to pass). I was hoping to lock things down a little without having to reconfigure all of the Tunnels. My though was that an ACL on the Inside Interface blocking selected traffic Out (so into the LAN) should not impact the stability of the Tunnels but allow me to restrict some traffic from entering the LAN. One port that I was attempting to block is RDP 3389. When this ACL is applied to the inside interface it does not block Port 3389 at all. What am I missing? Is it that the trffic is being allowed because it is coming through one of my 'open' Tunnels?
Shouldn't IPSec Tunnel traffic be processed by the Inside Interface ACL just like all other traffic?
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 3389
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 135
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 137
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 138
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 139
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 445
access-list 145 deny tcp 192.168.30.0 0.0.0.255 10.187.10.0 0.0.0.255 eq 389
access-list 145 permit ip any any
ip access-group 145 out interface Internal
This work great on a 2821 Router, but not so much on the ASA.
my environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
Region : France
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : orange
i have installed TL-MR3220 after my livebox (orange french box), my MR3220 is configurer on the DMZ zone in the livebox, internet is ok on the pc but when adsl signal is down on the livebox, the MR3220 don't switch to 3G connexion. The wan led is alway on in the router. But if i unplug the wn cable, the router switch on the 3G connexion. If i plug the wan cable the router kill 3G and use wan connexion.
How can i config my WAN config on the router for automatic switch by the router. Actually, the WAN config is fixed address (DMZ address in the livebox) Whis PPPOE id, the router can't connect. The livebox modem can't work on briddge.
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies View RelatedI am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies View RelatedWRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. After all that I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port.
View 4 Replies View RelatedWRT120N router: After several hours on the phone with Technical support I got nowhere. Guy had me putting in "admin" in the user name then the PW. I kept getting the 401 authorization required message. I reset my router and used the disk to setup again. After that I went again to the 192.168.1.1 and got the request for authorization, entered admin in the PW and it does nothing, just reloads the request and browser keeps connecting. I have WIN 7 HP, use Firefox 5.0 mostly, but tried on IE8 as well and it does the same thing. I am attempting to open a port. Also the support site has been down for over 13 hours for routine maintenance service.
View 2 Replies View Relatedhow i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
View 9 Replies View RelatedI have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View RelatedI am attempting to set up snmp v3 monitoring of my 2900 series routers from the third party Spiceworks utility. My snmp config on the router looks like this:
SNMP-Server view Westv3View internet included
SNMP-Server group Westv3Group v3 priv Read Westv3View
SNMP-Server user Westv3User Westv3Group v3 auth MD5 <password1> priv DES
[Code]....
I have set the logging level on the 2900 router to informational and see no errors of any kind popping up when I try to scan the router from SpiceWorks. Spiceworks just returns a generic "unable to contact host" message.
I've owned the Rev A DIR-655 for years and have loved it, but recently it started acting up. I have a complicated setup saved as a gateway settings file (.gws). I decided to purchase a new DIR-655 for the ease of importing my settings without having to manually setup again, however, much to my dismay, the new file format for the configuration settings on the Rev B is not .gws but rather .bin. The .gws file will not import. I tried changing the file extension to .bin with hopes it might import but no luck. I also found the utility which decrypts the .gws file into .xml and used those values to manually re-enter the settings into the Rev B router, but my port forwarding is not working the same. I was wondering if there is any utility to convert the .gws file to the .bin file in order to import into the Rev B router, or if not, can I still purchase the Rev A model somewhere. The online shops I've checked do not list the hardware version.
View 7 Replies View RelatedModel : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.8 Build 110418 Rel.43954n
ISP : SBB - Serbia Broadband[/COLOR]
I have been usung TP link for years, and now I want to use the 3G modem option the 3420 offers. But in the list of countries I can't find Serbia, and I can't find the ZTE MF 195. I found that on the TP Links site list of compatible modems there is Other countries, but in the modem list there isn't such an option, and since there is also no ZTE MF 195, and there isn't a "Telenor" entry for the service provider.I tried telling the router that I'm from another country, and setting up some of the parameters manually, but "surprisingly" it didn't work. Is there or could someone make a program which makes BIN files specific to the modem that isn't on the list, or is there a place where the BIN files grow?
just noticed today, that there's a FW ver.4.13 for Rev.D, which I uploaded into the router too. Captcha is now gone (I read it was flawed anyway), and no option to turn it back on (I'd do anyway).So I'm looking for the older firmware that I was using for a year or so, which was 4.11. I found it and downgraded to it (actually, this was on another DIR615 rev.D), and guess what? No catpcha in that either!As far as I remember, I was using 4.11-B04 (but not sure, really), whatever it means, and now I only find 4.11-B02 everywhere.Is it possible that those FWs with buggy captcha have been removed from FTP servers worldwide?
View 5 Replies View RelatedI have home network with my Linksys E-4200.
My HP Microserver (Ubuntu +Samba+Apache) is connected via LAN. I have notebook (Windows 7). To my server (FILE+WEB) I have access only when I connected via LAN cable. In windows 7 i see my server and have access to the files. Webserver works also properly: access with the name of the server in web browser.
But by WiFI connection, there is no access ! The server has the reserved local IP-address, like 192.168.1.200.
What should I do to solve it? By typing "192.168.1.200" i see the localhost page, but nothing more!