The documentation for the 4410N states it supports 802.1x however, all I see is to configure 802.1x using mac address or using uername and password.
Does the 4410N support 802.1x using EAP? If so how is it configured?
I've looked over all the spec sheets and hunted around, can't seem to figure out if the RV016 or RV082 support PoE. what Cisco product would be best to inject PoE on a small business network. I have 1 RV016, and I'm looking to deploy a RV082 and WAP4410N, with the 4410 being the only device on my network that would need PoE, I'd rather not have to buy a dedicated PoE Switch or Hub just for that one device.
View 5 Replies View RelatedI need a power Injector compatible for WAP 4410N.
View 3 Replies View RelatedI would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.it is necessary to reset the table mac and other resources that are not possible via WEB GUI..I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.It has some important information about this topic, it is necessary to reset the table mac and other resources that are not possible via WEB GUI.
View 1 Replies View RelatedI installed one of these on a small network. It's going through a mini-switch 5 port netgear to a larger 16 port netgear. Users are only able to get (4Mbps, 5Mbps) down on a file transfer. Shouldn't I be able to get closer to 80 Mbps on a 100Mbps network when connected on 802.11N?
View 10 Replies View RelatedI'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies View RelatedI’m planning to use Cisco 4410N AP for my new office. I have 20 offices in 1st floor (20 * 15 FT floor size). I want to know is it possible to cover the entire floor using one 4410N AP?
View 3 Replies View RelatedHave a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies View RelatedI have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3 for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …
We are on our 2nd 4410N. we monitor the AP with software that graphs the signal strength. the first 4410N would completely dissappear for about 3 to 5 seconds every few hours, that would disconnect users and annoy them greatly. a few weeks after we bought it, we sent it back to Cisco who sent us a new replacement. we have been monitoring the new one and several times an hour strength strength drops about 50DB for about a minute. monitoring is done from about 15 feet away from the AP.
View 1 Replies View RelatedWe installed a new WAP 4401n to extend a network and plugged it into a D-Link mini swtich (5 ports). In about 2 minutes we got no activity on the switch. We pulled power on the mini-switch, waited a couple minutes and re-powewred. No activity. Looks like we blew the switch. Put another mini-switch in and it did the same thing in about 4 minutes.
The WAP4401n is a PoE ready AP. We are checking right now on whether it's a cable wiring problem or an AP problem.I believe we are using the RJ-45 data cable that came with the AP.
I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedHow does the implementation of encryption wep wpa etc in hardware cisco wap4410N ?
View 1 Replies View Relatedcan wireless router support up to 100 user including support network printer
View 1 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
I have seen posts and screen shots of WRVS4400N settings screens showing WDS but I can't find anywhere in my setup to enable WDS on my version 1. I am running firmware 1.1.13. This makes me think WDS is only supported on v2 of the WRVS4400N, is that correct?
View 1 Replies View RelatedDoes Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?
View 1 Replies View RelatedWe need U-APSD (a special WMM Feature).Does the WAP321-E-K9 Support this feature?We need it for powersave mode from cordless wlan phones.
View 1 Replies View RelatedBy any way can I achieve HA in 2500 controller? I dont mind even I didnt get Stateful switchover.
View 5 Replies View RelatedWe are Deploying New Stand Alone AP (Model:AIR-AP1142N-N-K9) in our infrastrucuture, through out our network, we used 802.11G Adapter for Wifi Clients throughout,
Coulple of Questions i Have,
1) In This New Access point i found only Radio0 -802.11N 2.4 Ghz & 5 Ghz , whether this Model AIR-AP1142N-N-K9 will Support 802.11G Adapters?
2) if Clients Comes up with 802.11 G Adapter will it Negotiate and Connect to it?, through out worldwide our network Wifi Clients used 802.11g network to Connect to wifi Network.
3) Also from Client PC is there a way to find what network adapter its running?
4) Correct me if i am wrong , if Client Laptops having G adapter, i Hope it will not Connect To Access point with N Adapter?
5) if these Access point Does not support G adapter, any way to upgrade or downgrade to other IOS to make this access point support G Adapters?
I would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
does 5700 have the heat-map support? can i load a floor-plan to the controller. i know we can make this with wcs. 7200 specifications controller must have load floor plan option.
View 1 Replies View RelatedDoes the 8500 support any SMOF SFPs? data sheet only talks about a MM based SFP.
View 15 Replies View RelatedTo determine if the 2811 and 1811 ISRs support Verizon or Sprint USB 3g modems?
View 1 Replies View RelatedI have an older Linksys WRVS4400N Version 1.1 VPN Router. I have it set to run in mixed mode G/N. I still can only get connection speeds of 54 Mbps though. How can I get my wireless N clients to see 300 Mbps speeds?
View 1 Replies View Relatedthat cisco ap 1142 will support WLC2506 or not .
View 2 Replies View RelatedDoes the WAP4410N access point for Small Businesses support any Discovery Protocol like Cisco Discovery Protocol (CDP) or Link-Layer Discovery Protocol (LLDP), both for sending and receiving frames? I did an extensive search on the manuals and I was unable to find it
View 1 Replies View Relateddoes wlc 2504 support air-ap 1262n-e-k9.if yes does the air-ap1262n need any upgrade or sometine to join the controller,this is versions & image for both AP & WLC2504: [code] and the below what i configure for my topology WLC connected to switch by Trunk linke allow all vlans.AP connected to switch by access mode for vlan 20. the IP address sechma :
1- WLC 192.168.10.1 , Gateway in switch 192.168.10.254 ( vlan 10 )
2- AP 10.10.10.2 ( DHCP ) , Gateway in switch 10.10.10.254 (vlan 20) DHCP server its the switch is self , we use the option 4
know if Cisco LMS will ever support the 2500 wireless controller ? I have just checked the supported devices for LMS 4.1 and the controller is not there.
View 1 Replies View RelatedHow Cisco Identity Service Engine (ISE) can work with WLAN controller 5508 to do the Local Web Authentication, on behalf tje guest profile is create using Cisco ISE guest management?
As i check Cisco ISE caveat wireless only support on LWA, and LWA not supported on Authorization's VLAN assignment.
what i need to concern abou the ISE authentication and authorization policy on behalf on Wireless LWA with use of ISE guest management case?
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies View Related