I'm trying to upgrade my frmware to the lastest one (classic firmware) I've downloaded this file multiple times [URL] When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
View 6 RepliesI tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View RelatedI have a 4200V2 acting as a Router and (2) more E4200V2's acting as Access Points,The E4200V2 acting as the Router is at Firmware 2.0.37, but, the other Access Points are at Firmware 2.0.36.126507 and when I try to have the Firmware Upgrade Utility in Setup update the Firmware it gives me this message:"Current Version: 2.0.36.126507Available Upgrade: Your router software is up to date"Where is the downloadable Firmware 2.0.7 located?How do I upgrade the Firmware Manually to 2.0.7 and should I ?
View 6 Replies View RelatedHaving problems losing connectivity so decided to upgrade firmware from v1.00.7 to latest version available.
Downloaded the upgrade file and log into web based administrator. Select file and click on UPGRADE button. A couple of clicks on timeline then: UGRADE FAILED
I am trying to upgrade the firmware on my Linksys v1 router from 1.0.02 to 1.0.03 over a remote 56Kb circuit. I appear to be having a timeout problem. The upgrade always fails. I have upgraded several E1200s in my office over ethernet, and the upgrade appears to finish when the progress bar is at 15%. However, on my remote upgrade, the progress bar gets to 98%, hangs for a few more seconds, and then pops up a window with "Upgrade failed".
I suspect that there is a timeout on the upgrade process, and that I can't upload the 3.8 MB firmware file fast enough. If so, is there any way to increase the upgrade timeout?
I have tried repeatedly to upgrade my firmware from 1.0.03 to 1.0.04, but it always fails with a message :cannot upgrade at this time..." I've tried both IE and FireFox, and both wired and wireless connection to my PC (Windows 7).
View 4 Replies View RelatedIf by mistake I have attempted to upgrade the firmware my router "WRT610N" via my wireless laptop and after 24 hours the same screen "upgrading router" continues displayed and the router does not respond, How do I fix this?
View 9 Replies View RelatedNew E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies View RelatedWhere can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies View RelatedI just purchased 3 E4200v2 routers. As I am prepping them to install, I am attempting to update the firmware from 2.0.26 -> 2.0.37. I downloaded the zip file from the Cisco support site and when unzipped the file is named FW_E4200_2.0.37.131047.SSA. When I attempt to do a manual update from the Admin page, I imediately get an image file is incorrect error.
I've downloaded the file a total of three times on 2 separate networks and have tried three different browsers to attempt the update, all with the same error. The support chat sessions have proven worthless, they seem very scripted and the last one kept trying to sell me a support contract...
I want to stay with the Classic firmware, even though it is lacking current bug fixes. Does anyone have a "good" copy of the 131047 firmware? It appears to me that the one on the Cisco site is broken.
Cisco keeps struggling with CCC firmware files.
Now the download link for E4200v2 CCC is available, but gives you an empty zip file (0 bytes). Quality Control is an unknown word at Cisco.
The file is no longer empty.
Is classic firmware 2.0.37 for the EA4500/E4200v2 vulnerable? I see that the workaround is to use the latest Smart Wifi firmware. How soon can we expect to see a classic firmware update? [URL] Linksys quote taken from a random review that I found on Amazon below......The manufacturer commented on this review(What's this?) Posted on Jul 26, 2012 9:53:51 AM PDT Linksys says: (MANUFACTURER) Jason, Cisco Linksys plans to offer Software Updates to the EA Series router for customers who choose a local management option (including Cisco Connect/Classic). We will continue to provide Customer Care and deliver SW Updates to address Security, Critical Bugs and User Interface issues as required. Customers can comfortably stay with the local management option and Cisco will deliver continued support.
View 9 Replies View RelatedAfter an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.
View 6 Replies View RelatedTrying to update my firmware 1.00.01 B15 to 1.00.01 B17. I downloaded the firmware to my desktop (using mac os X 10.5.5) and connected my computer directly to port 1 on the back of the router. I used the Firmware upgrade tool under the Administration tab to upload the new firmware file. The update progress starts but fails at 98%
View 4 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedI purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?
View 9 Replies View RelatedI have a stack of 4 Cisco Switch 3750 (1 x WS-C3750G-24T, 2 x WS-C3750-48P and 1 x WS-C3750V2-48PS) and I want to do an firmware upgrade of this stack. Actually, all the 4 switches are at the firmware version 12.2(50) SE1 "IPBase" and I want to upgrade them to 12.2(55)SE5 IPBase. According to the release notes, all the switches in my stack are supported.
To upgrade the firmware, I use the command "archive download-sw /imageonly /overwrite tftp://IP_Address/c3750-ipbaselmk9-tar.122-55.SE5.tar" The firmware gets uploaded correctly but then I get the error message "There is insufficient space in flash: to install the required image. Clean up some old images, and try again."
When I do a "show flash", I see that the switch has 5650944 bytes free of 15998976 bytes.
How can i upgrade my switches? Is there an error in my command which I use? Do I need to add an other option?
The problem is, the switches are located in a branch office and there is no direct access to them. Everything must be done remotely.
I would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies View RelatedI just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies View RelatedThe file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View Related[code]...
This is new EA6500 and The firsttime Setup My EA6500，Download New Ver Linksys Smart Wi-Fi Router Setup,he say Your router was not successfully set up.
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
I have a WRT110 wireless router which disconnects suddenly and continuously. In addition, its performance is really poor. The current firmware installed is 1.0.03. I found a new firmware for this model (1.0.04.10) but when I try to install it, I choose the .bin file downloaded from Linksys TechSupp website, click on the "Start Upgrade" button, but I always get the following message "Please designate the path to the firmware".
View 9 Replies View RelatedI had issues with my router incorrectly resolving URLs. For example, going to facebook.com would gtive me a "wiki does not exist" message. Pinging facebook.com would give me an IP that belongs to wikipedia. The answer was SUPPOSED to be upgrading to v3.0.03.I upgraded and now my router WILL NOT connect to my DSL modem. Oh, it says it's connected and shows the correct IP address for my DSL modem but the gateway is showing 0.0.0.0. Direct connection to my PC works just fine.I have cycled the power on both the router and the DSL modem several times. The DSL modem is working just fine. I have done several IP release/renew on the router. I have reset the router. To no avail. This firmware update (which completed successfully) seems to have killed my routers ability to communitcate with the internet.
View 4 Replies View RelatedWhen I attempt to upgrade the firmware, I receive error code 0x82BF010E. It wont allow me to complete the firmware upgrade on my Mac OS X (10.7.5)
View 3 Replies View RelatedPS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?
View 9 Replies View RelatedMy Linksys WRT54G router has been dropping out lately and I've been recommended to update its firmware as it is very out-of-date. Well, everytime I try to upgrade the firmware to it, I get an error message that says "the connection to the server was reset while the page was loading." I'm trying to upgrade the firmware through the router's site 192.168.1.1 under the adminstration tab
View 2 Replies View RelatedI am trying to upgrade the firmware, your web site requires the version number, my version is V8, your site offers up to 7.2 ?
View 2 Replies View RelatedI have a wrt54g (8.1) that was acting a little funny so did some googling and followed the instructions to install new firmware. First the installation failed, double checked to make sure I downloaded the correct file (FW_WRT54G_8.1.09.02_US_20071227.bin), did a reset and power cycle. Checked the information again and everything on the router setup completely disappeared.
View 8 Replies View RelatedThere is no “firmware” number after the model and I believe this router has never had a firmware upgrade. However, if I try to download any of the 3 upgrades from the Linksys support site I get the message “firmware not available, sorry for the inconvenience.” Since the suggested solutions to so many problems posted in the forum is to first upgrade the firmware, I find this response with no explanation quite annoying. I am having problems replacing my current hardwired Linksys two port router with the WRK54G wireless 4-port router. Questions regarding that problem I will post under a different topic. For now, how I can get the firmware upgrade for the WRK54G?
View 5 Replies View RelatedI have tried to upgrade the firmware to the latest greatest but keep getting the "Incorrect image file" error. I bought two of the V1 units and had no trouble with one of them but the other is frustrating me. I have reset it and even tried a tftp upgrade of the firmware but still get "Incorrect image file" even in tftp.
View 1 Replies View RelatedI have an E3000 with firmware v. 1.0.01 build 6. I am trying to upgrade to the latest firmware version. I downloaded the file, and when I went to install from the web page I got the error message: Not enough memory available. I tried from 2 computers and got the same message.
View 6 Replies View Related