I have tried repeatedly to upgrade my firmware from 1.0.03 to 1.0.04, but it always fails with a message :cannot upgrade at this time..." I've tried both IE and FireFox, and both wired and wireless connection to my PC (Windows 7).
View 4 RepliesHaving problems losing connectivity so decided to upgrade firmware from v1.00.7 to latest version available.
Downloaded the upgrade file and log into web based administrator. Select file and click on UPGRADE button. A couple of clicks on timeline then: UGRADE FAILED
I am trying to upgrade the firmware on my Linksys v1 router from 1.0.02 to 1.0.03 over a remote 56Kb circuit. I appear to be having a timeout problem. The upgrade always fails. I have upgraded several E1200s in my office over ethernet, and the upgrade appears to finish when the progress bar is at 15%. However, on my remote upgrade, the progress bar gets to 98%, hangs for a few more seconds, and then pops up a window with "Upgrade failed".
I suspect that there is a timeout on the upgrade process, and that I can't upload the 3.8 MB firmware file fast enough. If so, is there any way to increase the upgrade timeout?
I'm trying to upgrade my frmware to the lastest one (classic firmware) I've downloaded this file multiple times [URL] When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
View 6 Replies View RelatedIf by mistake I have attempted to upgrade the firmware my router "WRT610N" via my wireless laptop and after 24 hours the same screen "upgrading router" continues displayed and the router does not respond, How do I fix this?
View 9 Replies View RelatedI have an E3000 with firmware v. 1.0.01 build 6. I am trying to upgrade to the latest firmware version. I downloaded the file, and when I went to install from the web page I got the error message: Not enough memory available. I tried from 2 computers and got the same message.
View 6 Replies View RelatedI was prompted by Cisco Connect to upgrade the router software. During this process it came back and said the update failed. At this time the network connection dropped. The power light is now flashing on the device.
View 9 Replies View RelatedUpgraded my E3000 from 1.0.02 to 1.0.04 and now I cant get an ip from my arris modem. I did the 30/30/30 reset and everything but no luck. I've had to plug the modem directly into the computer for now. Where can I find the 1.0.02 download or how can I fix this?
View 3 Replies View RelatedI have comcast Triple HD cable internet and I have been using a low end 5 year old Linksys Router. I decided to upgrade and get the E3000. So far I have had no luck at all getting it to work. Setup fails to even connect at all. I spent 2 hours on the phone with tech support. There were in trying to get it up and running but we have been unable to get a TCP/IP number from my provider (comcast). I hooked up the old router to see if any of my settings looked unusual but they seemed normal.
View 9 Replies View RelatedAfter an indeterminate period my E4200 (firmware version 1.0.03) stops renewing the Internet IP address. This happens in both router mode and bridge mode.In router mode the E4200 is set for DHCP and connected to the cable modem, in bridge mode it is connected to a Dell switch with DHCP being provided by my Win2008R2 server.It appears that the device stops recognizing the existence of the Internet port - no lights come on when a cable is plugged in - whether connected to the cable modem or my Dell switch. Plugging the same cable into one of the 4 lan ports and that port lights up immediately (i.e. it is not a patch cable problem).If the E4200 is left switched off for some time (possibly days) it will work properly again for a while.
View 6 Replies View RelatedTrying to update my firmware 1.00.01 B15 to 1.00.01 B17. I downloaded the firmware to my desktop (using mac os X 10.5.5) and connected my computer directly to port 1 on the back of the router. I used the Firmware upgrade tool under the Administration tab to upload the new firmware file. The update progress starts but fails at 98%
View 4 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedI wonder if an updated firmware for E3000 would come out. Current one have few web-interface issues at QoS, DHCP, Custom Routes and WiFi setup pages.
View 9 Replies View RelatedI updated my E3000 firmware to Ver. 10.0.4 and did not backup the original firmware. How I can get the original firmware file for this router.
View 3 Replies View RelatedWant to switch to dualband E3000 from older, working fine except needs resetting often. What steps do I need to take? I do not have E3000 setup disk. I fear that I will go down a path that makes both of the routers unusable, at least down many hours.
View 9 Replies View RelatedPowerArchiver compression sw (newest version) does not recognize the file as valid archive
View 4 Replies View RelatedDownloading the latest firmware for the E3000. Seems like the link on the page is broken.
View 1 Replies View RelatedWill this router ever see a firmware update so that we can have some additional functionality? The version of Twonky Media server that was bundled with this router was old to begin with, and now we are stuck with it? I tried the E4200 but it just kept spinning my drive that's parked in a ThermalTake BlackX, at least the 3000 doesn't do that, but when can we expect some new firmware, it's been 8 months. I used to love Linksys, but with this kind of support I may have to move to a different brand, and I bet I am not alone. it doesn't break the E3000 like you broke the 4200.
View 1 Replies View RelatedI have a laptop with an Intel Centrino 6300 Ultimate-N wireless card. With the previous firmware I was able to reach 300mbps while on the 5GHz band. Since I updated my E3000 to the latest firmware (1.0.04) I can only reach speeds of 144mbps. I have done a factory reset on the router and stll get the same result. Is there any way I can get it to reach 300mbps again with the current firmware?
Also, yes I have uninstalled / updated the driver software for my wireless card. I have also changed the appropriate settings for the 5GHz band. (40MHz channel width, using WPA2 encryption)
I purchased a WRT160N router last Friday. After setting it up, everything seemed to work fine, but after a couple of hours, the router stopped responding to any requests. The LEDs stayed on as if nothing had happened, but the router was dropping everything coming from both the WAN and a wired LAN interface. Since than, I had to restart it 3 times during the last 3 days.The firmware is 1.53.0, which seems to be the latest firmware for the European market - even when I try to get a newer firmware, this site only offers the US version 1.02.2.Should I update the firmware to the US version 1.02.2 ? Is there any difference between the 1.53.0 and the 1.02.2 version ? Is there a way to restore the original firmware in case the update fails ? I haven't found any link to 1.53.0 version..Also, does this firmware updating affect my warranty ?
View 9 Replies View RelatedI have a stack of 4 Cisco Switch 3750 (1 x WS-C3750G-24T, 2 x WS-C3750-48P and 1 x WS-C3750V2-48PS) and I want to do an firmware upgrade of this stack. Actually, all the 4 switches are at the firmware version 12.2(50) SE1 "IPBase" and I want to upgrade them to 12.2(55)SE5 IPBase. According to the release notes, all the switches in my stack are supported.
To upgrade the firmware, I use the command "archive download-sw /imageonly /overwrite tftp://IP_Address/c3750-ipbaselmk9-tar.122-55.SE5.tar" The firmware gets uploaded correctly but then I get the error message "There is insufficient space in flash: to install the required image. Clean up some old images, and try again."
When I do a "show flash", I see that the switch has 5650944 bytes free of 15998976 bytes.
How can i upgrade my switches? Is there an error in my command which I use? Do I need to add an other option?
The problem is, the switches are located in a branch office and there is no direct access to them. Everything must be done remotely.
I have the latest firmware, have the settings correct (the UPnP is disabled and whatever)
Model number: E3000
Serial number: CVQ01KC13100
Firmware version: 1.0.04 build 6
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): PPPoE
Went out of town 2 weeks in March, and all through April didn't have any disconnects. Have had this problem since I got it, it gets really bad from time to time (like now). Thought it was my provider for the longest time, but found out if I connect via wired, no disconnects! Is re-flash simply downloading and installing firmware?
After a ugrade from Snow Leopard to Lion on my Imac, the software witch i have by mine E3000 router, works not longer anymore
View 1 Replies View RelatedI recently installed a firmware upgrade on my E3000 to firmware version 1.0.04.build 6. Since the upgrade I am unable to see any of my files on my network computer which is running windows 7. Before everything was fine and I could stream to my dvd players and dish receivers.
View 1 Replies View RelatedI just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
I would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies View RelatedI just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies View RelatedThe file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View RelatedI tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View Related[code]...
This is new EA6500 and The firsttime Setup My EA6500，Download New Ver Linksys Smart Wi-Fi Router Setup,he say Your router was not successfully set up.
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
I have a WRT110 wireless router which disconnects suddenly and continuously. In addition, its performance is really poor. The current firmware installed is 1.0.03. I found a new firmware for this model (1.0.04.10) but when I try to install it, I choose the .bin file downloaded from Linksys TechSupp website, click on the "Start Upgrade" button, but I always get the following message "Please designate the path to the firmware".
View 9 Replies View RelatedI had issues with my router incorrectly resolving URLs. For example, going to facebook.com would gtive me a "wiki does not exist" message. Pinging facebook.com would give me an IP that belongs to wikipedia. The answer was SUPPOSED to be upgrading to v3.0.03.I upgraded and now my router WILL NOT connect to my DSL modem. Oh, it says it's connected and shows the correct IP address for my DSL modem but the gateway is showing 0.0.0.0. Direct connection to my PC works just fine.I have cycled the power on both the router and the DSL modem several times. The DSL modem is working just fine. I have done several IP release/renew on the router. I have reset the router. To no avail. This firmware update (which completed successfully) seems to have killed my routers ability to communitcate with the internet.
View 4 Replies View Related