Cisco :: 1200 Series Upgrade Failure?
Mar 22, 2011
I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point keeps "rebooting" itself, I am assuming that the upgrade failed, how can I get the access point upgraded?
When I start to access the AP by typing "enable" and enter the password it starts resetting again.
I have reset the AP by the mode button, power option but still not working.
At this point I would even accept a fix to get it back to working condition. Here is a capture.
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 15 Replies
ADVERTISEMENT
Jun 7, 2012
I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.
View 1 Replies
View Related
Dec 3, 2012
I have a office network that was setup before I started. We have a 172. subnet and a 10.2 subnet. When users on Wifi get a 10.2 address ( ran out of 172 address ) they are not able to get out to the internet. But if the laptop is connected to a LAN port and get a 10.2 address they are able to get to the Internet. Not sure if its the Aps I need to configure or the Pix seeing that if they get a LAN address of 10.2 everything works. This is becoming a bigger issue now that the company has out grown its main subnet (172.)
APs= AIR-AP1231G-A-K9
Vlan = 172.16.1.XXX
Vlan2= 10.2.0.XXX
Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz
View 9 Replies
View Related
May 15, 2012
I am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies
View Related
Apr 19, 2012
I recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.
View 1 Replies
View Related
Nov 20, 2012
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies
View Related
Dec 30, 2012
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies
View Related
Jul 24, 2011
at one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
View 7 Replies
View Related
Nov 24, 2011
I have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
After showing the warning banner message it takes long time before asking for username.
The sh version is given below.
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15
[Code].....
View 3 Replies
View Related
Feb 20, 2011
I'm trying to upgrade a 3750-24TS from c3750-ipservices-mz.122-25.SEE2 to a more recent image. On the first pass, I got
Error: There is insufficient space in flash: to install the requiredError: image. Clean up some old images, and try again.
So I used the delete /recursive flash:image-dir-name to clean out the old files, but I'm still getting the same message after doing this. What's the problem? Now I have a switch with no IOS and need to at least get something on there.
Switch#sh verCisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Fri 28-Jul-06 08:46 by yenanhImage text-base: 0x00003000, data-base: 0x010CE290ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)Switch uptime is 1 hour,(code)
View 16 Replies
View Related
Jun 28, 2011
Tried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
View 5 Replies
View Related
Apr 5, 2012
This weekend we have upgraded the ios on quite a few switches on a larger site, the site is a mix of 2960 and 3560 switches and the previouse ios versions were 12.2.44 on most switches but some had an older 12.2.25.On monday when we came into work we got a call that most of the ports on these switches were an amber color and most people could't use the network.After some investigation we discovered that we had a problem with dot1x so for a quick solution we just removed it from the switches and restarted all the ports with no dot1x enabled,[code]
View 6 Replies
View Related
Jan 24, 2013
IOS upgrade tried on the stack of 2XWS-C3750X-24T-S , Upgrade was tried to support WCCP on the platform. Current version is Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE1, Not able find any IP Plus ios in the site ? Only available are IP base and Universal K9 , Tried upgrading to c3750e-universalk9-tar.122-58.SE2.tar by using stack upgrade method as per document [URL]
Upgrade fails with error :
%Error opening flash:update/info (No such file or directory)
ERROR: Image is not a valid IOS image archive.
Why current ios is not supporting WCCP , I hope it is there in the featureset. ( tried "sdm prefer routing" but no success) Does c3750e-universalk9-tar.122-58.SE2.tar will give me wccp support ? What is the issue with my upgrade and how do I do a successfull upgrade ?
View 3 Replies
View Related
Jul 20, 2011
I've been working with a client's integrated 3750 WLC running 4.0.179.11. I want to upgrade the code because it is old plus I am having DHCP trouble. I have a couple of questions:
1. Is it OK to upgrade to SWLC3750K9-5-2-193-0.aes ? or do I need to go through 4.2 first ?
2. Will that code upgrade the bootloader at the same time?
3. How can I make sure there is enough flash space on the WLC?
4. Are there any special considerations to plan/prepare for?
The DHCP issue is failure of associated clients to get an IP address with this message found in WLC debugging:
[Code]...
View 10 Replies
View Related
Nov 5, 2011
applied an iOS update to a stack via tftp. I used the archive Download-sw tftp:// method. I rebooted the stack after complete and it never came back up. I discovered the master switch upgraded but not the member. The member was sitting there with all amber lights on and frozen after the iOS load. The master wouldn't finish boot until I removed the member from the stack. I had a version mismatch and they would not communicate.
View 2 Replies
View Related
Dec 20, 2012
7x stack WS-C3750E-48TD-E orignal code 12.2.35...i wanted to get it to 15.0.1 so as a test i disconnected top switch (not the master ) and installed via archive download-sw /allow upgrade 15.0.1.tar. and it worked away fine...
so i moved onto the stack, issued the same command, image loaded rebooted and stack hung..Consoled in and switch was unable to boot..looping on trying to load flash. [code]
View 8 Replies
View Related
Mar 10, 2013
I have tried to upgrade the firmware to the latest greatest but keep getting the "Incorrect image file" error. I bought two of the V1 units and had no trouble with one of them but the other is frustrating me. I have reset it and even tried a tftp upgrade of the firmware but still get "Incorrect image file" even in tftp.
View 1 Replies
View Related
Sep 14, 2010
I was prompted by Cisco Connect to upgrade the router software. During this process it came back and said the update failed. At this time the network connection dropped. The power light is now flashing on the device.
View 9 Replies
View Related
Feb 12, 2011
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies
View Related
Aug 30, 2011
I am facing a constant problem with cisco 7940 Ip Phones.
- I am able to configure it from Call Manager.
-But after that the phones starts restarting.
- I heard there is some issue with CISCO 7940 Farmware in recent times.
How to upgrade Firmware and where to get one.
View 4 Replies
View Related
Jan 3, 2012
I have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies
View Related
Oct 8, 2012
I have Cisco Catalyst Stack structure that consist of;
3750E-48TD-S (MASTER) (UNIVERSAL Image)
3750G-48TS-S (IPBASE Image)
3750G-48TS-S (IPBASE Image)
3750G-48TS-S (IPBASE Image)
I want to upgrade their IOSs to k9 images.
I can not dowload Universal Image file from Cisco website because of the expired service contract. I have IPBASE IOS files for all switches,
Can it be a problem to upgrade master switch IOS from Universal to IPBASE image?
View 1 Replies
View Related
Apr 11, 2012
My task is to upgrade a couple of 6500 series switches, 6513 with SUP720/MSFC3 (WS-SUP720) and Policy Feature Card 3 (WS-F6K-PFC3B) installed. How to upgrade those switches if in SSO redundancy mode with two SUPs installed?
I understand that it is good to connect to the MSFC3 via console and upgrade this first, is this correct?
I also have to upgrade some 6509 but I only can test it on one 6509-E, how to get everything up to date. [code]
View 1 Replies
View Related
Sep 25, 2012
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
View 2 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Jun 2, 2012
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies
View Related
Jul 24, 2012
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies
View Related
May 27, 2012
My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies
View Related
Jun 14, 2011
Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies
View Related
Jun 3, 2004
I run into a 1230 that would have a Web page completely different than the usual one. Instead of getting the normal User/pass menu and then the menu on the left side frame, you get this:
Cisco Systems
Accessing Cisco AIR-AP1220-IOS-UPGRD "1200AP"
Web Console - Manage the ap through the web interface.
Telnet - to the router.
Show interfaces - display the status of the interfaces.
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Extended Ping - Send extended ping commands.
Show tech-support - display information commonly needed by tech support.
Everything appears to work ok in that peage excepting the "Web Console" link which would probably go to the usual home page.Getting to it from the console, everything looks to be ok. You can configure the unit using the IOS and the unit apparently works fine. I have 12.2(13) JA3 running.I defaulted the unit, reloaded the image... I'm still getting that home page.
View 4 Replies
View Related
May 28, 2013
We have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
View 35 Replies
View Related
May 24, 2012
I have been looking for a new router that can handle intensive bandwidth for my office which can handle vlans, QoS, bandwidth management, VPN/VPN Passthrough, and perhaps multi-WAN/Load Balance. A friend has recommended the Mikrotik RB 1200 for my application, having looked at the product the feature set seems to be quite extensive and the price point is very attractive. The router is also rack mountable (a big plus!!!), my question is wether the router is relatively easy to configure/manage. I have managed/installed other routers such as the Cisco SMB series but I have no experience with Mikrotik. I am very tech savvy and have a moderate knowledge of network infrastructure. I have heard so may different responses to the simplicity and I would like y'all to weigh in before I purchase the router. (OR WHATEVER RACKMOUNTABLE ROUTERS YOU RECOMMEND FOR SMB)
View 10 Replies
View Related
