Cisco WAN :: Updated 2950 Switch Software Which Caused Network Assistant Error
Jun 23, 2011
I have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies
ADVERTISEMENT
Mar 18, 2013
I recently updated my NVIDIA nForce 10/100/1000 mbps ethernet driver and now my computer wont connect to the internet. In fact, it doesnt even acknowledge that the ethernet chord is plugged in. I am running windows 7 and have had no problems for years now. Since ive had my PC for so long I decided it was time to update, now im at a loss of what to do. I am currently using my laptop to submit this post, as my PC is not a wifi enabled device. I recall having this problem back when I first had this computer made and found a resolution online, (cant seem to find the same site i used back then.) I recall that it had something to do with me using the command prompt. While i have been looking for an answer, I have tried the following with no avail:
Reset IPv4 TCP/IP stack to installation defaults. netsh int ipv4 reset reset.log press enter
Reset IPv6 TCP/IP stack to installation defaults. netsh int ipv6 reset reset.log press enter
Reset WINSOCK entries to installation defaults: netsh winsock reset catalog press enter
Restart the computer after.
View 1 Replies
View Related
Mar 14, 2013
We are getting "Warning: Saving this config to nvram may corrupt any network management or security files stored at the end of nvram.” And “% Configuration buffer full, can't add command: a0/14” message. " message, when we try to save the configuraiton in one of the 2950 switch.
View 3 Replies
View Related
Oct 21, 2012
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
View 2 Replies
View Related
Nov 6, 2012
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies
View Related
Feb 13, 2012
As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
View 4 Replies
View Related
Jan 10, 2011
we recently updated all of our WLC's to 7.098 and it all went smoothly, controllers rebooted and AP's updated their firmware and rebooted OK.One WLC (4402) which was working fine since the update now has no AP's associated. The AP's were all configured to run in HREAP mode and are on remote sites within our WAN. I have checked that all policies and ports are still open (none have changed anyway) but the AP's can not join with the contoller.The log from an AP trying to join with the WLC.
[Code] .....
The logs on WLC show as below.
*emWeb:
Jan 12 13:14:13.629: %AAA-5-AAA_AUTH_ADMIN_USER: aaa.c:1289 Authentication succeeded for admin user 'adann'*spamReceiveTask:
Jan 12 13:14:12.919: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:a4:10 supporting CAPWAP*spamReceiveTask:
Jan 12 13:14:11.543: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:8f:a0 supporting CAPWAP*spamReceiveTask:
[Code] ......
View 5 Replies
View Related
Feb 11, 2012
I've connected a dslmodem/router to a fast ethernet port(fa0/1) on a 2620 router.There is a 2950 switch connected to the other port (fa0/0).I can ping the Internet via the router but and the switch but not from a host connected to the switch.I can't reach the dslmodem from the host pc.I've configured nat(overload) on the router.
View 8 Replies
View Related
Jun 9, 2007
I downloaded an update for the 1370 wireless card from the microsoft site and now my wireless network doesn't work. I went to the dell site and got the driver directly from the dell site (R140747.EXE) and it fails after it reached 59% complete. I tried another download recommended from this forum (R151519.EXE) and the same error at 59%. I have tried everything I have seen in the forums (closing virus software, editting setup ini file, etc) and I still get Update 778 error at 59%. I am running on an Inspirion 6000, CARD (CIRCUIT), IRELESS, MINI PCI CARD, 1370, BROADCOM CORPORATION, Dlink wireless router, windows xp with sp2, USA. I have also received an error that says something about internal setting incompatible (unfortunately I didn't capture the exact wording - I will attempt to recreate the error) This is terribly frustrating considering I was only following the dell suggestion that I update the driver and now that I attempted it, my laptop is sitting not being used.
View 5 Replies
View Related
Jan 27, 2013
I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
View 2 Replies
View Related
Sep 25, 2012
I recently replaced my harddisk and ever since I've been getting BSOD's whenever I try to watch a video online (no matter what website I'm on). I'm pretty sure it's not my GPU, because I can watch my own videos just fine. It could be the RAM,ause I ran Memtest86+ for 7 passes and it found two errors, but I have no problems playing games. So, I'm thinking it's my network-driver (Realtek) even though I already (re)installed the latest version[CODE]
View 1 Replies
View Related
Jan 16, 2011
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies
View Related
Jun 25, 2006
i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies
View Related
Dec 27, 2012
I'm experiencing considerable difficulties with CNA and my 4948E cat's. Front panel view, vLans and VTP utterly fail...and I have gone to GREAT lengths. I initially configured them all for comprehensive use in a vSphere environment. Storage switch fabric and multi-vlan guest networking. I wiped the config's across the board, factory reset all of them in an attampt to get CNA working. NO GO and it's been wildly frustrating, 80+ hrs spent with no results.
So is CNA truely compatible with the 4948e? And if so, WHAT IN THE **** AM I DOING WRONG!!?!?!?!!!!!?
Config and info:
C4948#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.1(1)SG2, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Wed 24-Oct-12 02:27 by prod_rel_team
ROM: 12.2(44r)SG11C4948 uptime is 22 minutesSystem returned to ROM by reloadSystem image file is "bootflash:cat4500e-entservicesk9-mz.151-1.SG2.bin"Hobgoblin Revision 21, Fortooine Revision 1.40
Last reload reason: Reload command
[Code]...
View 11 Replies
View Related
Sep 19, 2012
CNA 5.8(1)
32 devices
When I first launch the application, it promots for CCO login information, but then tells me the username or password is invalid. I reset it once, and it appeared to work. Next time I launched the application though, it gave me the same login error and did not store any of the device credentials. This is a new install of CNA and it just has one community setup on it now. I've tried 2 different CCO accounts and they both give the same login failure. I know the passwords I'm using are correct though.
View 15 Replies
View Related
Aug 15, 2011
I m getting below error messages in show logs -
Aug 12 15:30:57.127 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:02.175 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:08.219 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:10.239 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
there is no error messages related to PSU in "show env all " log .
here is show version -
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by cisco Systems, Inc.
[Code] ....
View 8 Replies
View Related
Oct 18, 2012
I'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies
View Related
Feb 28, 2011
Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
View 4 Replies
View Related
Feb 22, 2011
2950s work fine when upgrading the IOS using CNA. On all 2960s I get Failed to execute the command archive download-sw /overwrite /http iosFile
If I run the command using telnet and tftp server it works fine.
I have tried by deleting the old image then trying upgrade using CNA, but no luck
View 1 Replies
View Related
Jun 5, 2013
I'm having an issue with port-security on a cisco 2950 switch. The port-security is setup to user sticky mac-addresses and was working just fine. Recently when a computer was changed out and I needed to clear the security on the port it wouldn't let me.I would type clear port-security sticky int fa0/## and it would give me an error. The error would be that the sticky command doesn't exist.So I went back and type clear port-security ? and the only option was dynamic. Even if I try to take the port security off the switch it wont let me, it never shows the option for sticky.If I change the maximum number of mac-addresses allow the computer will work, but I can never clear the old addresses out.
View 3 Replies
View Related
Oct 22, 2012
CNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
View 2 Replies
View Related
May 16, 2013
With my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
View 16 Replies
View Related
Feb 16, 2012
I have a Cisco 2948G switch that I am trying to communicate to through this program. It has both an IP address and is hooked up through a cable. I can get Cisco Network Assistant to come up and ask for it's Username and Password, and that it is where I am stuck! I have no clue as to what to put in there as a username and password? I do have a password setup on the switch to login in to it during terminal mode, but that is it.
View 1 Replies
View Related
Mar 22, 2011
Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
View 2 Replies
View Related
Dec 30, 2012
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies
View Related
Mar 3, 2011
I keep having no internet connection on my home wireless network, usually when i download newer versions of software, such as iTunes or java. this only happens on my dell inspiron laptop 1525. my other computers in my house work just fine. i have windows vista on laptop. the only error message i get is:The network adapter Bluetooth Network Connection in not connected. the only solution i have found so far is to do a system restore to a previous date, and voila, i have my internet connection back, no problem.
View 3 Replies
View Related
Sep 28, 2011
We have installed last Network Assistant version, 5.6(3), but we can't add any switch to it.... It says always "Unsopported Device type: unknown".Our switches are all 2950, 2960 and 2970 models.
View 4 Replies
View Related
Apr 2, 2012
why Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies
View Related
Jul 6, 2012
first I replaced a new internal hard drive. Installed new and updated drivers. connected to the home wireless network. everything working well so far as of last week. this week, I replaced new battery and ran norton 360 updates. after the updated, I can't connect wirelessly to my home network. I checked if Norton is blocking the communication but I don't think it did.
View 3 Replies
View Related
Jan 10, 2013
Im looking to connect up 4 new pcs to network but I don't have enough wall ports. I thought I could plug cisco 2950 switch into the port on the wall and act like a hub. The switch configuration is default and there is only one vlan. How is it that it won't connect. Does it need a crossover cable.
View 3 Replies
View Related
Mar 16, 2011
My internet (via wifi) works just fine. But here is the situation that has me baffled-I have a house that has ethernet wired ports in each room, then there is a central hub in my closet. In the hub, I have a grey ethernet cord that is labeled 'service'. This service wire connects to a board that features 12 ethernet ports, 1 of which says 'in', 1 says 'security interface' and has a little nub in it, and the other 10 are not labeled. The grey wire is in the 'in' port.So I am left with 10 ports- port 3 of 10 has a (phone cord size) cord in it, connecting into the 'line' port on my Qwest modem/router. (Qwest set this all up for me, by the way). The modem/router is obviously plugged into the wall. Now- remaining loose in the hub are 9 ethernet cords- 5 blue, 4 green. Each one of these is written on in sharpie, and has a room label on it. 'Family, living room, kitchen, etc...'. So, pretty obvious, I simply found which cord corresponds to the room I am trying to use (family GREEN is one, family BLUE is another). These 2 wires correspond to the top port, and bottom port of a switch plate that is in my family room. Now- inside the closet hub I plugged family GREEN and family BLUE into the back of the ROUTER, ports 1 and 2 (of 4 available). Now- I went back to the wall- connected ethernet wires into the wall plate and then into the ethernet devices I am trying to use (slingbox and directv dvr). Neither are working.
If I go to setup menu on dvr it says it cannot find a network, not getting an ip address. is that the slingbox red lights are both solid (which means there is a connection), and if I go back to the router ETH1 and ETH2 are lit up on the front, again implying that I have a valid connection. This isn't rocket science, but I must be doing something wrong. Are the family GREEN and family BLUE supposed to go into any of the 9 remaining ports that are open inside the closet hub? Because my thought was- let's say hypothetically I wanted to use every available wall jack in my house. There are 9 wall jacks total, but there are only 4 ports on the router. So this would not work. But, there are 9 ethernet ports open on the board in the closet. So I must need to use the ports in the closet, NOT on the router? If so, are these closet ports specific? Because (remember I have a phone like cord coming out of port 3, going into the 'line' port on my router/modem) I took this phone like cord out of port 3, plugged into port 4. and 5, and 6, 7, etc... and none of them would allow my wifi to work- the INT light goes off on the modem/router at that point. But when I plugged back into port 3 (where Qwest originally put it), INT lit back up and wifi worked again. So this makes me think that these 10 (9 remaining) ports are specific somehow? I know this was a lot to read. End result I am looking for- continue to use my wifi on the computer (the ONE place in my house there is no wall jack lol), and connect my slingbox and my directv dvr to the wall jack in my family room so I can (have slingbox) and get On-Demand content for directv.
View 5 Replies
View Related
Jul 29, 2012
I updated my Mac to OSX 10.8 and now every time I try to login to my work network (a windows network) it locks my account. Each time, my sysadmin unlocks my account and I am able to successfully login one time but then, if I login again (after restart or sleep) I am locked out.
View 1 Replies
View Related
Dec 27, 2010
I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
View 4 Replies
View Related
