Cisco :: 4402 / Updated WLC Has Strange Error Log And APs Not Joining?
Jan 10, 2011
we recently updated all of our WLC's to 7.098 and it all went smoothly, controllers rebooted and AP's updated their firmware and rebooted OK.One WLC (4402) which was working fine since the update now has no AP's associated. The AP's were all configured to run in HREAP mode and are on remote sites within our WAN. I have checked that all policies and ports are still open (none have changed anyway) but the AP's can not join with the contoller.The log from an AP trying to join with the WLC.
[Code] .....
The logs on WLC show as below.
*emWeb:
Jan 12 13:14:13.629: %AAA-5-AAA_AUTH_ADMIN_USER: aaa.c:1289 Authentication succeeded for admin user 'adann'*spamReceiveTask:
Jan 12 13:14:12.919: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:a4:10 supporting CAPWAP*spamReceiveTask:
Jan 12 13:14:11.543: %LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:21:a0:81:8f:a0 supporting CAPWAP*spamReceiveTask:
[Code] ......
View 5 Replies
ADVERTISEMENT
Mar 6, 2012
LAP join process: 70:ca:9b:25:5b:9d -> AP MAC10.10.1.30 -> DNS
View 8 Replies
View Related
Oct 17, 2011
Last week and just yesterday, our switch SG200 50/50 logged an error like this:
%CDP-E-MALFORMED_TLV: CDP message from 88:43:e1:ab:66:f8 cached with illegal Appliance VLAN-ID TLV
At the time of the error, the SA520 router's LAN Port 1 where the SG200 Port 49 connected went down. (Light is OFF) So internet is down and other V LAN are disconnected. The MAC address on the log is the SA520 router. This happens 2x now and it needs for me to reboot both switch and router. and goes back again online.
SG200 50/50 Port Firmware 1.1.1.8
SA 520 Firmware (Primary/Sec):2.1.51/2.1.18
View 4 Replies
View Related
Jun 5, 2011
my MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies
View Related
Dec 12, 2011
this is what happens when I try to join an acs 5.3 to the domain. On two other acs appliances, it works.
View 1 Replies
View Related
Dec 6, 2012
I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.
View 10 Replies
View Related
Jun 23, 2011
I have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies
View Related
Aug 27, 2011
I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
View 10 Replies
View Related
Jun 9, 2007
I downloaded an update for the 1370 wireless card from the microsoft site and now my wireless network doesn't work. I went to the dell site and got the driver directly from the dell site (R140747.EXE) and it fails after it reached 59% complete. I tried another download recommended from this forum (R151519.EXE) and the same error at 59%. I have tried everything I have seen in the forums (closing virus software, editting setup ini file, etc) and I still get Update 778 error at 59%. I am running on an Inspirion 6000, CARD (CIRCUIT), IRELESS, MINI PCI CARD, 1370, BROADCOM CORPORATION, Dlink wireless router, windows xp with sp2, USA. I have also received an error that says something about internal setting incompatible (unfortunately I didn't capture the exact wording - I will attempt to recreate the error) This is terribly frustrating considering I was only following the dell suggestion that I update the driver and now that I attempted it, my laptop is sitting not being used.
View 5 Replies
View Related
Dec 20, 2011
we have a production network that uses five SG300 switches that functions brilliantly most of the time. four of our switches run in layer 2 mode and the last switch runs in layer 3 as it is used to route our 7 vlans as well as routing traffic between our two gateways. the switches use the original firmware that shipped with the devices (v1 device) and will be upgraded within the next week. the problem that we have is that the network seems to stop routing for all of the hosts after a given time. the only way to fix this issue usually is to reboot the main layer 3 switch. the main layer 3 uses a default route to one of the gateways and a return route has been applied in the gateway. the only thing i can think is that somewhere one of the devices routing tables become full and the network stops responding.
View 2 Replies
View Related
Mar 24, 2011
I have an ASA 5520 with 2GByte RAM running Software Version 8.2(4)4.
As soon as I enable outside interface Gi0/0 I get the following error message on the console every now and then:
(set_exptime) Timer not a leaf 0x714644dc. Traceback: 0x805e4b3 0x8061b92 0x855ce33 0x85606e7 0x85634ee 0x8563f53 0x8564664 0x8564a12 0x85623a5 0x8063b63
mgd_timer_set_exptime: Not a leaf called from 0x855ce33
I have configured a second 5520 as failover mate and once I have activated the failover device and the configuration replication was finished this second device started the same tracebacks immediately.
View 4 Replies
View Related
Apr 22, 2013
The issue that I am having is that the network cable I have that going from my router to my desktop computer, seems to be flaky, at least it seems that way...When I try to use the network cable that goes into this desktop, into another computer(one that I know works), the connection status alternates between connecting, and no network cable detected, connecting...and no network cable connected, and so forth.it NEVER connects. When I plug the cable back into the desktop, it does the same thing for maybe a minute, but then eventually connects. However, every other computer, laptop, macbook, another desktop PC, that I have tried connecting using this same cable never connects.
View 5 Replies
View Related
Aug 13, 2011
My desktop PC has occasional hiccups in which I can't connect to any website (via any browser, I've tried Firefox, Chrome, Opera & IE) for short periods of time (usually ~1 minute) but all other Internet connectivity seems to be normal. (I can ping Google for instance, and I remain connected to Google Talk, but I can't load the Google website.)
I recently did a fresh install of XP Pro SP3 and am pretty confident that there is no malware running on the system. (I'm running Microsoft Security Essentials and Windows Firewall but I also did a Malware Bytes scan which uncovered nothing.) The desktop is connected wirelessly but I don't suspect an issue with the router because my laptop (via wireless) and my girlfriend's desktop (via wired) can surf the web just fine when my computer is experiencing issues.
I checked for proxies (both in the browser settings and in Windows settings) but everything appears to be setup correctly (that is, unproxied.) DNS is set to the proper DNS servers for my ISP (Cox) but I also tried switching to Google's DNS servers with no luck.
View 3 Replies
View Related
Feb 23, 2012
My Wi-fi on my rig seems to have some odd problems. When I'm gaming i often get a lag spike every 10-20 second or so, and before I got the "Vista anti-lag" program I was also getting the enormous 60 second lag spike. I'm sure many Vista users recognize this problem. But here is the deal, the first kind of lag spikes completely disappear while talking on Skype! Which makes me wonder, what is it with Skype (only while talking) that removes the lag? Gaming with Skype makes all games run fluently without any spikes at all.
View 2 Replies
View Related
Jul 6, 2012
Basically I started disconnecting when I logged onto Blacklight Retribution after a recent game patch, after a few days the problem stopped and I was able to play again (with no changes to my computer) a few days later another patch was added and the problem occurred again, at first I thought it was a Blacklight specific problem (as this was my only installed game) however i installed a few other games (Kabold Online, Perfect World, Forsaken World, TF2, MW2 and C9) and I got the same problem on each of these games. I haven't been able to log onto a single Online game for more than 5 minutes, normally I'm disconnected at login, HOWEVER, my internet works completely fine in for everything else, i can browse the web, download game clients etc with no problem whatsoever.(Forgot to add, When i disconnect my LAN Cable mysteriously Unpluggs itself (according to computer) and a disable/enable in network manager reconnects it)
- Checked to see if drivers were up to date (they were)
- Rolled back NIC Driver (and put it back when this didn't work)
- Checked device manager for any problems with my NIC, (working as normal apparently)
- Tried setting my NIC to 100mbps Full Duplex
- Setting my power options to not interfere with NIC
- Had a DHCP error in my event logs so i set my gaming machine to a static IP
- Turned of UnUP, Turned on DMZ
- Turned off "Green Ethernet"
- I had other Errors in the form of a service stopping my NIC
- Phoned ISP, Everything is OK there end but they sent out a new router, but problem still occurs
- Noticed that a service was sending a stop control to my NIC, looked on forums for fixes and applied several of them
- Reformatted computer with old XP (switched from windows 7), updated, installed latest drivers etc and still same problem except now I don't get anything in event viewer when the problem occurs.
The only thing i haven't tried is replacing my NIC, but considering the internet works completely fine for everything but Online games I'm unsure how this could be the problem.
View 9 Replies
View Related
Aug 12, 2012
I keep getting log messages like the following on my router:[RV220W]Tue Aug 14 00:00:14 2012(GMT+0200) [RV220W][Kernel][KERNEL] BW_LIMIT_PKTS IN=LAN SRC=10.0.0.10 DST=173.194.35.134 PROTO=TCP SPT=1159 DPT=443,i.e. a large number of BW_LIMIT_PKTS messages regarding traffic from the LAN to the WAN destined to ports 53, 443 and 80 only. Is it related to QoS policies? What is the meaning of this message?
View 3 Replies
View Related
Mar 25, 2012
I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
View 3 Replies
View Related
Sep 1, 2011
Our costumers has implemented 2 AIR-WLC4402-50-K9 with Software Release 7.0.98.0, the wireless infrastructure consist in 2 Root-Mesh-LAP and 8 Mesh connect over-the-air to deploy outdoor coverage.
All the LAP are Aironet 1520 Series Mesh Access Points with equipped with 3 antennas for 2.4GHz and 1 antenna for 5GHz (backhaul).For one year all seems to be ok, yesterday after a power outage of one Mesh-Root-LAP, 5 Mesh-Lap continues reload each 10-12 minutes, on the WLC Log you can see event like a reboot from AP Console, on the LAP console i can capture this event before the reload:
Log on LAP Mesh
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0
%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:
Radio Not Beaconing for too long ....
LWAPP-5-CHANGED: CAPWAP changed state to DOWN
AP1780-Mesh uptime is 11 hours, 10 minutes
System returned to ROM by power spike
%DOT11-6-GEN_ERROR: Error on Dot11Radio0 - Not Beaconing for too long - Current 0 Last 0%SYS-5-RELOAD: Reload requested by Dot11 driver. Reload Reason:Radio Not Beaconing for too long ....*Sep 1 16:05:43.399: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
What does it mean? That the beacon signal trasmitted from Root-Mesh-LAP cannot reach the Mesh-Lap and so the Mesh-LAP force a reload?Where we should search the cause? In the power instability or in a interference on the 5GHz radio interface?
On one of mesh Lap I found a strange reason for a releoad:AP1780-Mesh uptime is 11 hours, 10 minutesSystem returned to ROM by power spike
Log on WLC
Log System Time Trap
0 Thu Sep 1 17:31:11 2011 AP Disassociated. Base Radio MAC:00:22:be:41:33:00
1 Thu Sep 1 17:31:11 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
2 Thu Sep 1 17:31:11 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:22:be:41:33:00 Cause=Heartbeat Timeout Status:NA
[Code]....
View 7 Replies
View Related
Jan 30, 2013
we want to replace our 1242 AP's with the 1602 model and so far everything works like a charm. We have just noticed, that most of the clients which are connected on the 5GHz N radio, the web interface of the AP1602 shows his own host name instead of the clients host name.
For example:
Radio0-802.11N2.4GHz
SSID INTERN :
[code].....
The Host name of the 1602 is "AP-LABOR", so why it shows the own host name for the Dell E6420 Notebooks on the 5GHz radio and on some "NONE"?
View 1 Replies
View Related
Apr 13, 2013
I've a WRV210 Wireless-G VPN Router with RangeBooster, that logs this alert almost every time, "Packet type : 0 -- free socket buffer only".Also each time that some devices, like Android, are connected to the Wifi, the wifi starts a reboot and drop cycle.
Some extra context information, I've connected to the router a Cisco Gigabit switch and all the wired devices are connected to the switch, that could overload the router? Other point I've a Cisco VOIP gateway connected to the router and a few VPN's and firewall rules setup.
View 1 Replies
View Related
Nov 13, 2011
I have searched the forums, and can see that I am not the only one with speed problems on this router. When I changed from a D-link dir-615 (yeah, no wonder I changed it ) my download speed dropped from 4-5 MB/s to 1,3 MB/s. I'm using a wired connection. Have tried disabling QoS in router settings, did a firmware upgrade, reset the router. You see, when I do speed tests on the internet I get 40-50 mbits download, 25-30 mbits upload. I have tried many different files to download, both torrents and through my browser.
View 2 Replies
View Related
Apr 5, 2011
I am monitoring my WRVS4400N with SNMP and create graphs by MRTG. Problem is that data about traffic are strange, very low. I have 50 MB line but max traffic shown on graphs is about 8000 bits per second. Also the "shape" of graph does not correspond with real traffic.
View 1 Replies
View Related
Dec 15, 2011
I have a VPN tunnel between two 892s. When either ISAKMP or IPSec SA lifetime expires tunnel stops processing traffic. However nothing is logged in the syslog. But when I enable debug crypto isakmp error and debug crypto ipsec error following entries appear:
ISAKMP:(0):Can't decrement IKE Call Admission Control stat outgoing_active since it's already 0
ISAKMP:(2041):R-U-THERE-ACK sequence number 0x63D809BB does not correspond to expected value 0x63D809BC
%CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=XX.XX.XX.XX, prot=50, spi=0x3560099E(895486366), srcaddr=YY.YY.YY.YY, input interface=GigabitEthernet0
ISAKMP:(2043): IPSec policy invalidated proposal with error 4
Is this a bug? IOS is Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1)
View 2 Replies
View Related
Apr 13, 2012
My ASA 5510 IOS version 8.4.2 CSC IOS version is 6.6.1125,I configured ACLs and Class maps to forward all HTTP,HTTPS,SMTP,PoP3 and FTP taffic to CSC.Here my issue is my CSC not getting updating from the internet and some email sites like Webmail and Gmail are not taking forward after entering credintials. If i removed ACL belongs to the HTTPS , all are working fine( CSC updating well and all email sites are working.)
View 1 Replies
View Related
Jun 11, 2013
I updated an AP1121 accidentally with the LWAPP version of an AP1130ag.
View 1 Replies
View Related
Aug 30, 2012
Now that Comcast is in the process of rolling out IPv^ to their customers nationwide, will there be a firmware update that properly displays the IPv6 /64 address as provided by the cable provider? Currently the only IPv6 address displayed is on the LAN page and is not configurable (greyed out) except for the prefix length. I already have a cable modem that will provide both IPv4 and IPv6 addresses as they are rolled out.
Currently running WRVS4400N v2 fw 2.0.2.1
View 1 Replies
View Related
Apr 20, 2012
There is new firmware for the B series of the Dir-825 but the change log is not updated.
View 10 Replies
View Related
Nov 22, 2012
BGP prefix list is not updated when other party having new downstream with different AS number.BGP filter has disabled but the prefix list is still not updated.BGP soft reset is performed, but the prefix list is still not updated.BGP prefix list is only updated when the other party having new prefix with the same AS number.Can explain why?
View 1 Replies
View Related
Mar 3, 2011
I keep having no internet connection on my home wireless network, usually when i download newer versions of software, such as iTunes or java. this only happens on my dell inspiron laptop 1525. my other computers in my house work just fine. i have windows vista on laptop. the only error message i get is:The network adapter Bluetooth Network Connection in not connected. the only solution i have found so far is to do a system restore to a previous date, and voila, i have my internet connection back, no problem.
View 3 Replies
View Related
Sep 17, 2012
We have three WAP4410N that loses the connection. We've updated the firmware, changed the equipment, repeatedly reconfigured, but the problem persists.Is used the firmware 2.0.5.3 with WPA2 Enterprise Mixed authentication.
View 5 Replies
View Related
Jan 14, 2013
After updating driver Intel(R)82578DC Gigabit Network Connection my computer cannot find modem Experiabox from KPN (Netherland). Temporely solved by restore to the old version?
View 1 Replies
View Related
Jul 6, 2012
first I replaced a new internal hard drive. Installed new and updated drivers. connected to the home wireless network. everything working well so far as of last week. this week, I replaced new battery and ran norton 360 updates. after the updated, I can't connect wirelessly to my home network. I checked if Norton is blocking the communication but I don't think it did.
View 3 Replies
View Related
Dec 30, 2011
Ever since I updated my wireless NETGEAR WNR1000v2 Firmware to its current Version V1.1.2.28NA I'm unable to connect to the internet with my PSP Firmware version of 6.60. I used to be able to connect up with no problems. I can scan and it sees the connection and i'm able to set the PSP network settings up however when I go to test it it will not connect up.
View 4 Replies
View Related
