Cisco :: Band Select On 1131AG?
Feb 24, 2011Do the 1131AG APs support band select from a 4400 WLC running version 7?
View 2 Replies
ADVERTISEMENT
Cisco Wireless :: WLC 5508 / Is Band Select Is Enable By Default On 7.2.110
Sep 27, 2012I have several WLC 5508 with 7.2.110 firmware. My questions are:
(1) Is band select is enable by default on 7.2.110?
(2) All the variables settings on the band select, how do I set it up to make 5 ghz more preferable than 2 ghz?
Linksys Wireless Adapters :: How To Select 5GHz Band For AE1000
Mar 4, 2011The product literature for the AE1000 says that you can select which band to use. However there doesn't seem to be an option to do that. I have an E4200 and when I set it up, it assigned my 5GHz and 2.4GHz bands the same SSID. If I configure the AE1000 to connect to that SSID, it seems to connect to the 2.4GHz band. Do I have to change the SSID for 5GHz and initiate a connection to it manually?
View 9 Replies View RelatedLinksys Wireless Router :: No Connection To 5GHz Band On E3000 Dual Band?
Apr 14, 2010I have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.
View 9 Replies View RelatedTP-Link Dual-Band Wireless :: DHCP Not Working For 6 GHz Band?
Apr 2, 2013Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
To Select Between NFS And NIS Lan
Mar 27, 2013I have 2 computers running Slackware 13.37 and each has a T10/100 ethernet card/port. I want to create an ethernet network between them to pass text and possibly backup. I have given them 192.168.2.1 and 192.168.2.2. I want to be able to cut the connection at will. If I recall correctly there are 2 types of LANs one is NFS and NIS. Which would be the best for this purpose and where can I find a stepwise approach to setting it up?
View 1 Replies View RelatedCisco Wireless :: 1131AG APs As Bridges?
Feb 27, 2012I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedCisco Wireless :: Disable Led On 1131AG While Associated With WLC
Jun 9, 2010On autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies View RelatedCisco Wireless :: 1131AG AP Not Able To Boot
May 31, 2012My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
Cisco Wireless :: IOS Of LAP 1131AG Is Corrupted
Jun 5, 2011IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies View RelatedCisco :: Multiple SSIDs On 1131AG?
Jun 21, 2011I am trying to use two different SSID's on my 1131AG each with different security, is this possbile?
View 1 Replies View RelatedCisco :: LMS 3.2.1 Can't Select Devices In NetConfig
Jan 19, 2012After upgrading to LMS3.2.1 I cant select devices in Netconfig. There seams to be a defect in the selection box:you have Task selection twice (left task-selector headlined with Device Selector) instead of device-selector left and task-select right.What can we do to can use netConfig?
View 1 Replies View RelatedCisco Wireless :: 1131AG Not Joining To Controller (7.4.100)
Apr 2, 2013My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
Cisco Wireless :: AP 1131AG Cannot Upgrade From Version 3.0 To 7.3
Feb 14, 2013I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies View RelatedCisco Wireless :: Clients On 1131AG Cannot Talk To Each Other
Jul 27, 2012I have a dozen clients on an 1131AG and they cannot ping each other. I get a reply but it says destination host unreachable.
View 4 Replies View RelatedCisco Wireless :: 1131AG Can't Browse Domain
Jul 25, 2012We have six 1131AG WAP's, lightweight, managed through a 2514 controller. We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.
View 3 Replies View RelatedCisco Wireless :: Activate WAP4410N And AP-1131AG?
Mar 16, 2011I have WAP4410N and AP-1131AG for the school lab's Access point. First, WAP4410N doesn't make connection to wired network.
There's no DHCP server in our school and uses below :
192.168.x.x ip address
255.255.0.0 Subnet
192.168.1.254 Gateway
210.220.16.7 DNS address.
So I seted these settings on the configuration page, but when I connect to the WAP4410N wireless, I can't connect to the internet. Problem reporter in Windows 7says there's IP adress problem on the access point. ...but the ip address is correct. I did everything on the manual ....
Second, AP-1131AG. I entered with console cable and changed the ip address. And I enabled wireless radio(default:disabled) but I cannot find SSID with wlan. I added SSID on SECURITY-SSID manager. It says 'interface on' on 802.11a/g, but it is the same. I can't find SSID. other labtops can't, too.. tried using vlan. FAILED....
Cisco :: 1131AG - Max Retransmissions And Interference Threshold?
Apr 30, 2013We're getting complaints about a specific 1131AG in the field only being intermittently accessible. WCS shows both the a and b/g interfaces randomly bouncing, sometimes the reason for the bounce is unknown other times it says it's because it lost connection to the controller. I can ssh into the WCS but the engineer who setup the AP's doesn't seem to have enabled remote access via telnet or ssh.
We are also seeing these events:
802.11a interface of AP * is down: Controller 172.17.0.10 Reason: Max retransmissions for the AP have reached.Interference threshold violation reported by '802.11b/g' interface of AP *, connected to Controller '172.17.0.10'.I know I can adjust the threshold percentage, but that would only seem to mask the issue.WCS gives this version info on the AP:
Versions
<DIV style="DISPLAY: block" id=versions mcestyle="display: block;">
Software Version
6.0.202.0
Boot Version
12.3.8.0
[code]....
Cisco Routers :: RV120W Cannot Select N Speed Under Wi-Fi
Aug 27, 2012I recently purchased a RV120W router and I am having a problem selecting n speed under the wireless settings.
If I select B/G/N-Mixed mode then when I go to save the change I get B/G/N-Mixed B/G/N-Mixed in red letters and it does not save. If I select N only then when I go to save it says in red letters N only N only.
It does not matter if I pick 20 only or 20/40. It does not matter if I enable or disable U-APSD. It does not matter if I use the LSB or USB side.
Firmware Version:1.0.3.10 :When I got the router it had an older firmware if I remember correctly, and it would let me change to n speed.
Cisco VPN :: 2801 - SSL VPN Error On IOS / Cannot Select Private Key
Mar 12, 2011i have a Cisco 2801 router which is running ssl vpn, previously my ssl vpn is working, but when i reset the config to factory default and restore the working config, then i experienced this problem;
Here is my crypto config, here is the error:
CRYPT O_PKI: Can not select private key (key name)
webvpn gateway web vpn-gateway host name sslvpngtwy01 ssl trust point key name in service.
Cisco Wireless :: Select AVC Profile On WLC Based Via ACS 7.4.1
Feb 4, 2013I just saw the AVC feature in WLC version 7.4.100.0 and wonder, if there is a possibility to select a AVC profile per user, based on it's RADIUS authentication via ACS.For example:
- A user in group teacher can access youtube on SSID A
- A user in group student can not access youtube on SSID A
How To Select Optical Transmission Mode
Apr 4, 2013560km long pipeline, intermediate station at every 30 or 40 kms. Couple of Ip phones, 2 or 3 IP camera, and few control signls (IP system) will be connected at every stations. Do not expect heavy data. Which one may be the prefered economical solution can I use
1. Ethernet network (Switch with Optical SFP ports at every site)
2. SDH equipment at every site
3. DWDM equipment (if so lower end)
Cisco Wireless :: 1131Ag Showing Operating Status Down
Feb 16, 2010I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies View RelatedCisco Wireless :: 1131AG Series AP Supported By WLC 4400?
Jan 21, 2013I am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
Cisco Wireless :: WLC AIR-WLC2106-K9 With 2 X Aironet 1131ag Not Appearing
Oct 3, 2012we have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
Cisco Wireless :: 1131AG - How To Disable Syslog Counter
Oct 24, 2012I can't figure out how to disable the syslog counter on my 1131AG WAP. See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
I've tried both of the following commands, neither one removes the counter:
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
how to rid the syslog counter
Cisco Wireless :: 1131AG AP With 5508 Controller Lighting?
Jun 5, 2013I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"
View 8 Replies View RelatedCisco Wireless :: 1131AG And Radio Reset Code 46?
Apr 24, 2012I have a problem with one of our 1131AG AP, B/G radio go down:
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?
Cisco :: Select A Default Route Within MPLS/VPN Network
Nov 30, 2012I have this topology: ( I use OSPF instead of EIGRP for routing between PE CE. The customer vrf name is cusA, they have 4 sites: CE from site 3 have 2 links to 2 PE ( one for backup). CE from site 3 has exist point to internet and how can i choice 1.1.1.2 is next-hop for default-route
View 2 Replies View RelatedCisco WAN :: 3845 - Select NTP Server Version On IOS Router
Dec 26, 2012I have the following commands on my Cisco 3845 router running IOS version 12.2(24)T4:
ntp server 192.168.1.1 prefer
ntp server 192.168.1.2
ntp source loopback0
I see that the router is sending out NTP version 4; however, my NTP server is configured to accept only NTP version 3. Anything other than version 3 will be dropped.
How do I go about to configure NTP on the Cisco IOS router to send out only version 3 and not version 4?
Cisco :: Requirements For VLAN Select Feature In 5508 WLC?
Jan 8, 2013We implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies View RelatedWireless :: Speakers And Control To Select Choice Of TV's?
Oct 10, 2011Sports bar with many Tv's playing differnet games, want the ability to have tables select the tv and hear the audio for their TV,Each table to have set of small speakers and a dial to select the tv.
View 1 Replies View RelatedCisco WAN :: Find Out IP Address Of Aironet 1131ag Wireless Router?
May 30, 2011How do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies View Related