I have 2 computers running Slackware 13.37 and each has a T10/100 ethernet card/port. I want to create an ethernet network between them to pass text and possibly backup. I have given them 192.168.2.1 and 192.168.2.2. I want to be able to cut the connection at will. If I recall correctly there are 2 types of LANs one is NFS and NIS. Which would be the best for this purpose and where can I find a stepwise approach to setting it up?
View 1 Replies560km long pipeline, intermediate station at every 30 or 40 kms. Couple of Ip phones, 2 or 3 IP camera, and few control signls (IP system) will be connected at every stations. Do not expect heavy data. Which one may be the prefered economical solution can I use
1. Ethernet network (Switch with Optical SFP ports at every site)
2. SDH equipment at every site
3. DWDM equipment (if so lower end)
After upgrading to LMS3.2.1 I cant select devices in Netconfig. There seams to be a defect in the selection box:you have Task selection twice (left task-selector headlined with Device Selector) instead of device-selector left and task-select right.What can we do to can use netConfig?
View 1 Replies View RelatedDo the 1131AG APs support band select from a 4400 WLC running version 7?
View 2 Replies View RelatedSports bar with many Tv's playing differnet games, want the ability to have tables select the tv and hear the audio for their TV,Each table to have set of small speakers and a dial to select the tv.
View 1 Replies View RelatedI recently purchased a RV120W router and I am having a problem selecting n speed under the wireless settings.
If I select B/G/N-Mixed mode then when I go to save the change I get B/G/N-Mixed B/G/N-Mixed in red letters and it does not save. If I select N only then when I go to save it says in red letters N only N only.
It does not matter if I pick 20 only or 20/40. It does not matter if I enable or disable U-APSD. It does not matter if I use the LSB or USB side.
Firmware Version:1.0.3.10 :When I got the router it had an older firmware if I remember correctly, and it would let me change to n speed.
i have a Cisco 2801 router which is running ssl vpn, previously my ssl vpn is working, but when i reset the config to factory default and restore the working config, then i experienced this problem;
Here is my crypto config, here is the error:
CRYPT O_PKI: Can not select private key (key name)
webvpn gateway web vpn-gateway host name sslvpngtwy01 ssl trust point key name in service.
I just saw the AVC feature in WLC version 7.4.100.0 and wonder, if there is a possibility to select a AVC profile per user, based on it's RADIUS authentication via ACS.For example:
- A user in group teacher can access youtube on SSID A
- A user in group student can not access youtube on SSID A
I have this topology: ( I use OSPF instead of EIGRP for routing between PE CE. The customer vrf name is cusA, they have 4 sites: CE from site 3 have 2 links to 2 PE ( one for backup). CE from site 3 has exist point to internet and how can i choice 1.1.1.2 is next-hop for default-route
View 2 Replies View RelatedI have three computers in a Workgroup and I can transfer files through all the computers properly. However I cant set up permissions to who can access these files. The three computers are Windows 7 64bit desktop, Windows 7 64bit laptop, Windows XP Professional 32bit desktop.
What I tried so far...
Right-click on folder I wanted to share
Click on Sharing Tab
Click on Advanced Sharing>Permissions>Add...>Locations
I only see the name of the local computer, I don't see the two other computers on the network. The window looks similar to this, how I can find the other computers in my network, in the locations window.
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies View RelatedI have the following commands on my Cisco 3845 router running IOS version 12.2(24)T4:
ntp server 192.168.1.1 prefer
ntp server 192.168.1.2
ntp source loopback0
I see that the router is sending out NTP version 4; however, my NTP server is configured to accept only NTP version 3. Anything other than version 3 will be dropped.
How do I go about to configure NTP on the Cisco IOS router to send out only version 3 and not version 4?
We implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies View Relatedwas working fine with my new router DSL-2730U D-link router and using it's wireless connectivity with G/N mixed mode..and i noticed that the range is so low so i decided to switch to N-only mode and when i did that i couldn't connect at all!..the router uses N-150 btw.
View 8 Replies View RelatedI have an AE3000 dual band wireless adapter using the Win 7 Pro OS. At work our routers all use the same SSID, but utilize different channels. In terms of signal strength, the strongest signal is usually, but not always, one of the channels on the 2.4GHZ band (usually 11). However, in terms of speed of connection and lack of overcrowding, the best signal is invariably one the channels on the 5GHZ band (usually 161). My AE3000 will inevitably connect to the strongest signal (channel 11) even though it only slightly stronger than the signal on channel 161 and furnishes a much slower connection than that obtainable on channel 161. Is there any way I can "force" the AE3000 to connect via channel 161 rather than channel 11?
View 6 Replies View RelatedRegion : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
The product literature for the AE1000 says that you can select which band to use. However there doesn't seem to be an option to do that. I have an E4200 and when I set it up, it assigned my 5GHz and 2.4GHz bands the same SSID. If I configure the AE1000 to connect to that SSID, it seems to connect to the 2.4GHz band. Do I have to change the SSID for 5GHz and initiate a connection to it manually?
View 9 Replies View RelatedI just set up a DPC3825 router, and I wanted to use WEP security settings so my DS Lite can connect to the internet, but it appear the only options in the Wireless > Wireless Security dropdown list are :
WPA-Personal
WPA2-Personal
WPA or WPA2-Personal
Disable.
In an enviroment with WCS and a WLC5508 with 40 AP's (WAPs are either 1262's and 1252's), I have noticed that the bulk of users are infact operating on 802.11g although most operating notebooks are running 802.11n capable NICs (including my own laptops NIC - but yet when I connect I connect at 54Mbps.). Only a small portion of registered clients are using 802.11n. All my WAPs have both radios enabled?My question is how does a client notebook select a "prefered" band of 802.11n. I know in some cases the wireless NICs themselves have an option to select the "Prefered Band", but there are many notebooks out there that dont have this option. What would make a client connect at 802.11n over 802.11g? Who makes that call ?
View 4 Replies View RelatedDocumentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 Replies View RelatedWe have a mix of 1231 and 1242 access points in an LWAPP environment. They are connected to WiSM controllers in our 6509's and are managed by a central WLC. Everything is running version 7.0.230. My question is can I apply MAC address filtering on a select group of AP's to restrict access to a specific SSID broadcast on these AP's without affecting other AP's also connected to the same WiSM?
View 3 Replies View RelatedI can't choose any devices when I try to launch a NetConfig Job in LMS 3.2.
I have to check in the job summary if the device on which I'll apply the job is the good one.
Unfortunately, this problem doesn't appear every time so I don't know where to look for an answer.
I have several WLC 5508 with 7.2.110 firmware. My questions are:
(1) Is band select is enable by default on 7.2.110?
(2) All the variables settings on the band select, how do I set it up to make 5 ghz more preferable than 2 ghz?
how we can select a network module for 2811 router?gigabit or ethernet Hwic?
View 1 Replies View RelatedThe 5508 is running code 7.0.116.0. I have created a group interface for 3 subnets and assigned the group to the WLAN. Clients are getting IP addresses in a round robin fashion. The issue or downside to this is if the lease has not expired before the next time the station connects to the WLAN it consumes an address on another subnet instead of grabbing the unexpired lease IP address on it's previous VLAN. It seems that the WLC determines the VLAN in the interface group before the DHCP request from the client in case the client already received a DHCP address that has not expired. This can be problematic since we have seen some iPhones requesting an address every 20 minutes thus consuming an address on every subnet in the interface group. Other than setting a lease time extremely low what can be done to address this?
View 1 Replies View RelatedQ: If i m going to do a Bonjour Gateway deployment, do i still need the vlan select feature on the wism's or is enabling multicast enough?
Details of the Q:
I m working with WISM s and WISM2;s, 1130 and 3602 ap;s. Cores are 6509-E's.
i m going to implement a Bonjour gateway (which is an Aerohive ap, no wifi enabled, its just a Bonjour gateway)
This ap is connected with a trunk port (to a 6509-E) and has the wifi client vlans on the trunk as allowed vlans. It also has an allowed vlan for AppleTV;s which will be wired devices.
The Aerohive gateway gets an ip address in every wifi subnet, so far so good.
I was thinking that if i enable multicast :
- globally on the wisms, with mcast-mcast distribution
- on the SVI's for the wifi client vlans
- on te SVI's of the vlans for cisco aps
- on the SVI for AppleTV
- SVI for wism management
- SVI for the Bonjour gateway
then do i still need vlan select? Maybe a stupid question, but i m not sure how to interpret some things in this document.
I am calculating Cisco 4500X power consumption requirements to select appropriate UPS systems. I have 4500X switch with dual power supplies.which value should I take for power consumption calculation, in data sheet it has two values: AC Power Max Rating: 750W System Power Consumption: 330W nominal/400W max
Which values should I take, to calculate UPS systems capacity? And also I am interesting when 4500x has two power supplies what is power consumption?
I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies View Related