was working fine with my new router DSL-2730U D-link router and using it's wireless connectivity with G/N mixed mode..and i noticed that the range is so low so i decided to switch to N-only mode and when i did that i couldn't connect at all!..the router uses N-150 btw.
View 8 Repliesi am using a D-Link 2730u, was trying to change the username and password for the router but it keeps saying that ACS URL is required, there is a place where i can put one but even after goggling it for a bit i didn't understand what should i put in there?
View 1 Replies View RelatedRegion : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
I have two computers in the house which are linked by an ethernet cables, my wireless router only has one ethernet hole,so I would like to know what I need to buy? such as an adapter or something, so I can have two ethernet cables to connect to my router.the type of router I have is called a Hauwei echolite HG521 broadband wireless ADSL2+ router.
View 1 Replies View RelatedI have a TP-Link TL-WN723 USB WiFi adapter attached to my laptop, which runs WinXP Service Pack 3. It successfully detdcts the WiFi provided by my Edimax BR62-04Wg router, but when I try to connect, it cannot obtain an IP address and cannot connect to the network.
- The very same WiFi adapter can connect to other routers without any problem
- Any other device can connect to the very same network provided by my router without any problem
- Using the WiFi adapter with other computers does not work
Thus, it seems that the problem is somewhere between this specific router and WiFi adapter. Here is an interesting detail though:If I try connecting to my WiFi while a LAN cable from the router is plugged into my computer, the wireless connection establishes too. Even if I later unplug the LAN cable, the wireless connection continues to work. But it won't establish the connection without the cable plugged in.Here's what I've already know/tried:
- Rebooting the PC
- Re-installing the WiFi adapter's drivers
- All drivers and firmwares are the newest available
- Re-starting and reconfiguring the router
- Using the Windows client for wireless networking and the client included on the WiFi adapter's CD
- Changing the router's connection type to any available option: Access Point, Station Ad-hoc, AP Bridge WDS
None of these had any effect except for one:
- When I changed the router's connection type to Station Ad-hoc, I could connect wirelessly even without the LAN cable plugged in, and I had Internet access. However, in this case, other devices, such as smartphones could not detect the WiFi connection.
I have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies View RelatedToday I bought a TP-Link 150 Mbps Wireless PCI Express Adapter so I can pick up the internet connection in my house from my home PC. (We use a laptop most of the time which is able to pick it up fine).I've installed the wireless adapter into the computer and installed the drivers however I receive an error message:
"The device may not be present or could have been ejected/unplugged from the system. Insert of Reinsert Now."
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies View RelatedI just set up a DPC3825 router, and I wanted to use WEP security settings so my DS Lite can connect to the internet, but it appear the only options in the Wireless > Wireless Security dropdown list are :
WPA-Personal
WPA2-Personal
WPA or WPA2-Personal
Disable.
I have been using a TP-Link wifi adapter for last two months, It worked flawlessly till a couple of days ago. It just so happened that i turned on my computer and even though the wifi connections were available, when trying to connect this message keeps showing up " Windows was unable to connect to UoC WiFi". I have tried everything from making a new wifi connection to changing usb-ports
FYI I use the same wifi connection on my netbook and android, and they are working fine, so it's definitely not a problem with the ISP.
[code]....
Just bought a verizon 4g mifi.The laptop hooked up in a second to the device but i cant get my desktop computer to detect the connection.I tried using a USB Linksys wireless adapter then tried a netgear g-router but neither detect anything.
View 1 Replies View RelatedI need to connect a wireless router to a mifi 2200 for internet access.
View 1 Replies View RelatedI just changed my wifi modem and now I have a problem to connect my wireless g usb adapter on my PC to wifi. This wifi modem has a password. how to setup the network connection.
View 1 Replies View RelatedI am trying to use a MIFI hotspot for the internet, I have a wifi laptop, and a wifi printer.I would like to print wirelessly from my laptop and use the internet at the same time, but I can't. To print I have to go to my wireless network and switch to my router. And if I want to use the internet I have switch my wireless network back to the MIFI hotspot.
View 3 Replies View RelatedWill a realtek wireless network adapter connect to a Linksys WRT 110 router from a wood frame house to a concrete building approx. 100 ft. away
View 1 Replies View Relatedmy netgear wireless router cannot see my n300 usb adapter. it shows as working in my device manager, but the netgear router says wireless not connected. when installing the adapter it said that windows has an icon to the left of the taskbar that i can click on and ask to join a network, which it didnt. it just showed network and an option to open network and sharing center, which i did. there were no wireless networks that showed available for me to log into with the adapter
View 4 Replies View RelatedWRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies View RelatedSometimes I cannot connect to the router after my computer has been to sleep. This has occurred on different routers. I can still see the network, but am told I cannot connect when attempting to connect to it. Restarting/shut down does not solve the problem - I have to restart the router itself, and then my computer will reconnect automatically. Other computers/devices will be unaffected by this and maintain a connection the entire time. Atheros AR5B91 Wireless Network Adapter using Windows 7 Service Pack 1.
View 2 Replies View RelatedHow do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies View RelatedWhat is the best method (the one that works) to connect the E3000 with the SPA2102 phone adapter? Or, is it not possible?
View 9 Replies View RelatedI have the following commands on my Cisco 3845 router running IOS version 12.2(24)T4:
ntp server 192.168.1.1 prefer
ntp server 192.168.1.2
ntp source loopback0
I see that the router is sending out NTP version 4; however, my NTP server is configured to accept only NTP version 3. Anything other than version 3 will be dropped.
How do I go about to configure NTP on the Cisco IOS router to send out only version 3 and not version 4?
how we can select a network module for 2811 router?gigabit or ethernet Hwic?
View 1 Replies View RelatedSports bar with many Tv's playing differnet games, want the ability to have tables select the tv and hear the audio for their TV,Each table to have set of small speakers and a dial to select the tv.
View 1 Replies View RelatedI just saw the AVC feature in WLC version 7.4.100.0 and wonder, if there is a possibility to select a AVC profile per user, based on it's RADIUS authentication via ACS.For example:
- A user in group teacher can access youtube on SSID A
- A user in group student can not access youtube on SSID A
I have an AE3000 dual band wireless adapter using the Win 7 Pro OS. At work our routers all use the same SSID, but utilize different channels. In terms of signal strength, the strongest signal is usually, but not always, one of the channels on the 2.4GHZ band (usually 11). However, in terms of speed of connection and lack of overcrowding, the best signal is invariably one the channels on the 5GHZ band (usually 161). My AE3000 will inevitably connect to the strongest signal (channel 11) even though it only slightly stronger than the signal on channel 161 and furnishes a much slower connection than that obtainable on channel 161. Is there any way I can "force" the AE3000 to connect via channel 161 rather than channel 11?
View 6 Replies View RelatedThe product literature for the AE1000 says that you can select which band to use. However there doesn't seem to be an option to do that. I have an E4200 and when I set it up, it assigned my 5GHz and 2.4GHz bands the same SSID. If I configure the AE1000 to connect to that SSID, it seems to connect to the 2.4GHz band. Do I have to change the SSID for 5GHz and initiate a connection to it manually?
View 9 Replies View RelatedIn an enviroment with WCS and a WLC5508 with 40 AP's (WAPs are either 1262's and 1252's), I have noticed that the bulk of users are infact operating on 802.11g although most operating notebooks are running 802.11n capable NICs (including my own laptops NIC - but yet when I connect I connect at 54Mbps.). Only a small portion of registered clients are using 802.11n. All my WAPs have both radios enabled?My question is how does a client notebook select a "prefered" band of 802.11n. I know in some cases the wireless NICs themselves have an option to select the "Prefered Band", but there are many notebooks out there that dont have this option. What would make a client connect at 802.11n over 802.11g? Who makes that call ?
View 4 Replies View RelatedWe have a mix of 1231 and 1242 access points in an LWAPP environment. They are connected to WiSM controllers in our 6509's and are managed by a central WLC. Everything is running version 7.0.230. My question is can I apply MAC address filtering on a select group of AP's to restrict access to a specific SSID broadcast on these AP's without affecting other AP's also connected to the same WiSM?
View 3 Replies View RelatedI have several WLC 5508 with 7.2.110 firmware. My questions are:
(1) Is band select is enable by default on 7.2.110?
(2) All the variables settings on the band select, how do I set it up to make 5 ghz more preferable than 2 ghz?
Q: If i m going to do a Bonjour Gateway deployment, do i still need the vlan select feature on the wism's or is enabling multicast enough?
Details of the Q:
I m working with WISM s and WISM2;s, 1130 and 3602 ap;s. Cores are 6509-E's.
i m going to implement a Bonjour gateway (which is an Aerohive ap, no wifi enabled, its just a Bonjour gateway)
This ap is connected with a trunk port (to a 6509-E) and has the wifi client vlans on the trunk as allowed vlans. It also has an allowed vlan for AppleTV;s which will be wired devices.
The Aerohive gateway gets an ip address in every wifi subnet, so far so good.
I was thinking that if i enable multicast :
- globally on the wisms, with mcast-mcast distribution
- on the SVI's for the wifi client vlans
- on te SVI's of the vlans for cisco aps
- on the SVI for AppleTV
- SVI for wism management
- SVI for the Bonjour gateway
then do i still need vlan select? Maybe a stupid question, but i m not sure how to interpret some things in this document.
I'd like to use my D-Link router as a network adapter to connect a PC to my existing wireless network. how to configure the D-Link router? I'd like to leave the Belkin settings alone as much as I can.
I have a D-Link DIR-615. Hardware Rev. is C1. Firmware Rev. is 3.10NA.
I also have a Belkin F5D8235-4 router. Hardware Rev. is v2000. Firmware Rev. is 2.01.04
I have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.
View 2 Replies View Related