Looking to setup a backup router for our disaster recovery plan. We currently have a Cisco 877W that was setup by our ISP. I can log into the device with Telnet and a console cable, but I am not good using IOS commands, so I would like to use CCA. Unfortunatley, I cannot access the router using the software. I assume something is disabled in the config. Like HTTP or something.
View 1 RepliesI'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view. Here is the view of my Front Panel view after I connect the switch ?
View 2 Replies View RelatedWhile i was looking around in my stuff in the office i have found a Cisco 877W ADSL router .. so i have decided to use it instead of the one i am using now which is provided by the ISP that's made by Huawei.Anyway i have a good knowledge about basic cisco router configuration but i had never configured ADSL Cisco router, so i looked around on Cisco website, and i was lucky to get this two linksCisco DSL Router Configuration and Troubleshooting Guide - Step-by-Step Configuration of PPPoA with a Dynamic IP Address - Cisco Systems[CODE]
View 7 Replies View RelatedNTP server When I setup NTP server to take time from [URL] everything is working fine but as soon as I reset my router during boot I can see that router is first trying to get time before it's even connected to ATM and when it can't get time from NTP server it's removing NTP line from configuration (ntp server uk.pool.ntp.org source Dialer0 ). How I setup to wait with sync and do it once ATM connection is up and established? Or How to get IOS to leave this line and sync with NTP every 10 min)?
View 9 Replies View RelatedI have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedCNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
With my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
I have a Cisco 2948G switch that I am trying to communicate to through this program. It has both an IP address and is hooked up through a cable. I can get Cisco Network Assistant to come up and ask for it's Username and Password, and that it is where I am stuck! I have no clue as to what to put in there as a username and password? I do have a password setup on the switch to login in to it during terminal mode, but that is it.
View 1 Replies View RelatedI am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies View Relatedi have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies View RelatedI'm experiencing considerable difficulties with CNA and my 4948E cat's. Front panel view, vLans and VTP utterly fail...and I have gone to GREAT lengths. I initially configured them all for comprehensive use in a vSphere environment. Storage switch fabric and multi-vlan guest networking. I wiped the config's across the board, factory reset all of them in an attampt to get CNA working. NO GO and it's been wildly frustrating, 80+ hrs spent with no results.
So is CNA truely compatible with the 4948e? And if so, WHAT IN THE **** AM I DOING WRONG!!?!?!?!!!!!?
Config and info:
C4948#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.1(1)SG2, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Wed 24-Oct-12 02:27 by prod_rel_team
ROM: 12.2(44r)SG11C4948 uptime is 22 minutesSystem returned to ROM by reloadSystem image file is "bootflash:cat4500e-entservicesk9-mz.151-1.SG2.bin"Hobgoblin Revision 21, Fortooine Revision 1.40
Last reload reason: Reload command
[Code]...
CNA 5.8(1)
32 devices
When I first launch the application, it promots for CCO login information, but then tells me the username or password is invalid. I reset it once, and it appeared to work. Next time I launched the application though, it gave me the same login error and did not store any of the device credentials. This is a new install of CNA and it just has one community setup on it now. I've tried 2 different CCO accounts and they both give the same login failure. I know the passwords I'm using are correct though.
I'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies View RelatedSince I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
2950s work fine when upgrading the IOS using CNA. On all 2960s I get Failed to execute the command archive download-sw /overwrite /http iosFile
If I run the command using telnet and tftp server it works fine.
I have tried by deleting the old image then trying upgrade using CNA, but no luck
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies View RelatedI've been given a F5D7632-4 modem router which is said to be in working order, but without the Setup Assistant Software CD-ROM. How can I get a replacement for this?
View 1 Replies View RelatedI have new Belkin router and giving old one to my brother. It is F5D8233-4. Can I install without the CD "setup assistant"?
View 1 Replies View Relatedim trying to install a dell v715w all in one printer onto my macbook air, wirelessly. In order to do so the installation software says I need to download Dell Wireless Setup Assistant.
View 3 Replies View RelatedConfiguring QoS on my cisco877W for VoIP below is the current config. [code]
View 3 Replies View RelatedRegion : China
Model : TL-WR741ND
Hardware Version : V4
Firmware Version :
ISP :
My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?
why Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies View RelatedI have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies View RelatedCisco 877W. I configured it for PPPoE. But once I plug in the ADSL line, the dialer interface will get IP Address. But after like 2 minutes the PPP link will go off and I will get this log message: "Interface Vi1 unbound from profile Di1".
View 2 Replies View RelatedI am using a company called Zen for adsl, I have 8 IP from XXX.XXX.XXX.248 to - XXX.XXX.XXX.255, Gateway is 254, Address 249-250-251-252-253 I would like to appear at the 4 sockets at back of router, and 252,253 will be used for a server...I understand I should be using Routed IP , but I cannot get it to work, I can ping out to google from the server, but the server is not live to the world. [code]
View 8 Replies View RelatedI had the Cisco 877W Router working in my old company. The old company was closed and I bring all of network equirments to new company.I am trying to setup this router to new company but lost menu, console cable and software CD.
View 2 Replies View RelatedI have a Cisco 877W in place with an ADSL connection, which is working fine. However I cannot get it to hand out a DHCP address. If I associate with the AP over wireless then set a static IP I have full connectivity, similarly if I connect over Eth0 and set a static IP I have full connectivity. So it does just seem to be DHCP. Below shows my config... Any thoughts on the issue? Is it access-list related?I have checked with Wireshark and I see the DHCP request being sent out, but I don't see a DHCP offer being returned
View 4 Replies View Relatedhow to configure WPA2 /AES on 877W. Also how to enable IPS on the router. My ios is 12.4.11T1
View 7 Replies View RelatedI am running an 877W in the home that for the most part works fine, however after being connected for a variable amount of time I partially loose my DSL connection. Line sync stays up, but the traffic is lost.
A shut/no sut of the atm or dialer interfaces does not resolve the issue, only a reload or power down/up will fix the prob short term till it happens again.
Am currently running advipservicesk9-mz.151-3.T1, but have also rolled back to advipservicesk9-mz.124-24.T5 which has the same issue. Have tried a 857W with the same results. So ruling out IOS and hardware, its pointing to a config issue. It has also only been an issue since changing from ADSL1 to ADSL2+.
interface ATM0
no ip address
no shutdown
no atm ilmi-keepalive
exit
[code]....
I've tries some changes mentioned here and from other sites, but no success yet...
I have a working easyvpn setup. We need to change the HQ ip address (current it is i.e 85.146.110.101). This is ACL is applied to Fastethenet conecting to ISP:
interface FastEthernet4
description $FW_OUTSIDE$$ETH-WAN$
ip address dhcp
ip access-group 101 in
ip inspect SDM_LOW out
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto ipsec client ezvpn Acom
As soon as I apply again the ACL to interface Fastethernet 4, access to internet is lost. If I put original ACL 101 (with ip address 85.146.110.101) it works fine.
So I am wodering what wrong with may ACL? Should I make the change via SDM not CLI (to be honest I did not know/use SDM before today)?
I've an 877W with four V LANS, All bridged (group) onto a BVI which is bonded to ATM etc for ADSL:
c870-advipservicesk9-mz.124-15.T5.bin"
1 is the backbone, and for the switch, and has DHCP running and working with no problems - x.y.1.z . Multicast is enabled so that various multimedia bits of kit can find each other.
2 is the "primary" WiFi, which has android devices as they cannot handle SSID not being broadcast or devices that can only do wep.(WiFi radio) it has DHCP, x.y.2.z which works fine. Multicast is enabled so that various multimedia bits of kit can find each other.
3 is a secondary WiFi for the kids, "hidden" ssid. They are fire walled so that bugs can't infect any other windows PC DHCP x.y.3.z.
4 Is a secondary WiFi for our laptops, "hidden" ssid .
For some reason, DHCP is not working on 4. it was working until the good lady of the house quizzed why her net was not working... I've concentrated on vlan4, as there are no "local" access-lists definitions to stop anything. I've enabled debug ip dhcp server, and can see requests serviced on Vlan2, but not on 4, I've enabled/re enabled encryption/ shields on Vlan4, but still can't see dhcp requests arriving and do not see them being stopped somewhere. I can see that the station authenticates OK, but if I connect the same laptop to v lan 02, requests pour in and are answered, proving it's maybe not a Microsoft problem.
Let me just say, I'm more or less self taught with the the net, no real mentoring, so 'think' I have the general idea of the different layers, access-lists etc. so this config is probably not ideal, but it works.
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
[code]....