Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 4.23
ISP : GTPL
I recently bought Tp-Link wr740N model but when i run Easy setup assistant on my Windows 8 64bit, A Welcome page appears. When i click START button , a windows error comes out saying. TP-LINK Easy Setup Assistant has stopped working with following error
[code]...
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
Region : China
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
tried to run the easy setup assistant but failed the connection test. The WLAN indicator did not flash or light up, don't know if that is the problem.
Have checked the cables and they are working fine. As this router is 3 yrs old, should I get a new one? Does it appear to be a hardware problem?
Region : Ireland
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
I am trying to setup my DVR for remote access but my public IP and the routers WAN are not the same?
Region : China
Model : TL-WR741ND
Hardware Version : V4
Firmware Version :
ISP :
My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to setup an adhoc network using TPLINK WR740N without using any internet connection?I want to setup a WLAN connection between my Desktop and 2 other Laptops for file transfer and sharing.... how to search and connect to other available wifi networks using my router?
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
wan led on my router is not illuminating. My internet connection is fine.I have pppoe connection. What may be the reason ?
Region : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to change my router password?
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
i m experiencing wireless disconnects every 5 or 10 minutes and all i have to do is too disconnect from the router in windows from Wireless connections panel , and reconnect and it ggets fixed for some time again . i got so frustrated that i changed to openwrt , the disconnection problem is gone but not getting the 150Mbps.
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.16.3 Build 130104 Rel.55864n
ISP : ISP
My Wireless setting
Wireless Radio:Enable
Name (SSID):Trojan_Horse
Channel:8
Mode:11bgn mixed
Channel Width:Automatic
MAC Address:A0-F3-C1-97-87-FA
WDS Status:Disable
I cannot access the WiFi signal beyond 20m....There is no obstacle in the path. My receiver also supports 802.11n. There is also no local network interference.
Region : Ireland
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Three Mobile
I have recently purchased a new desktop computer that does not have an internal WiFi card. To remedy this I bought the TP Link TL-WR702N. Currently my access to the internet is provided by a mobile WiFi router (one of these: { URL}, that spreads a wireless signal throughout my house for things like my phone and laptop to connect to. I was under the impression that the WR702N would be able to connect to this network and let my new computer run on it (I believe it's called client mode?)
Now so far I have not been able to get my computer to recognize the existence of the TP Link modem, despite both Ethernet and USB cables being plugged into the computer. I think I need both logging in and changing the mode from AP to client mode.
I emailed support and was given the instruction to read this FAQ [URL], however, when following those instructions, after clicking on "Change adapter settings" instead of reading the router, all I get is a blank screen.
Region : Others
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
Region : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
Region : Philippines
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Local PPPoE
I'm using this router for connecting 2 PCs, one lap top and few mobiles.The LAN network is always stable and never loses connection, but I'm having problems with the wireless connection. My lap top runs on wireless, and 3 Android mobiles, an xperia mini pro (problematic), xperia Tipo and Alcatel OT-908F. Almost always when I login to facebook on any of the mobiles, pictures won't show, and also youtube videos thumbnails won't show. On the xperia mini pro after 2-3 minutes of surfing, or doing anything else the connection drops, and then the mobiles can't see the wireless connection. My lap top can see it, but it cannot connect. After restarting the router everything is back to normal.
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
I seted up router and i coud acces the utility window, then i switced from w7x32 to w7x64 and then i try to acces the utility window i can only see.Username or Password is incorrect.Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". The settings will be restored to factory default after the resetting.
How to restore the device to the factory default settings?Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings.no pop up window appears i tried looking this up and the closest thing i found was to un-check the proxy but its not checked so what should i do to be able to access utility window?
Region : Others
Model : TL-WR740N
Hardware Version :
Firmware Version : 120320
ISP : connect communication
HOW CAN I BLOCK USER FROM MY ROUTER WHO USES WIRELESS WITHOUT CHANGING PASS BECAUSE I WANT HIM TO KNOW PASSWORD BUT HE COULD NOT CONNECT
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : Lexus
I am using tp link router for accessing internet in my laptop and mobile. everything is opening in my laptop but i had few problems when using internet in mobile. im using android mobile. when using play store the images and screen shots of applications are not loading but im able to download. I'm unable to see the images in play store. So I'm thinking that there is something problem in router settings.
Region : Sweden
Model : TL-WR740N
Hardware Version : V4.20.0
I have a TL-WR740N. If router is on and I turn on my laptop it will not automatically connect to the router. I must turn off the router and then turn on again to get connection to the Laptop. I think I have missed something in configuration of the Laptop.
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : I am trying to set up my router for about 2 days without any effect.
Here you can find, what I have to do to connect through Ethernet cable to the internet at our university:[url]....
When I set auto-detect IP on router, it says that I have Static IP. In CMD I can find out all the information about the connection and the licence is usually for one day (automatically renewing). I've also tried to clone MAC address, nothing happened.
Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx
783/31/2013 17:04PPPINFOsent [LCP ProtRej]
793/31/2013 17:04PPPWARNINGPPPoE link down
[Code].....