I have a problem in the ACE 4710. In view of the connections of a web environment. When I view connections on Config> Operations> Real Servers, Conns column values appear very high connections (Example. 1606317769078).Already in Config> Operations> Virtual Server the number of connections appear normal. Version 4710 ACE Device manger A4 (2.1a)
View 1 RepliesI am getting sync fail on device manger A3(2.2) to ACE 4710 appliance when I am changing certificate in one of proxy service.
View 1 Replies View RelatedIn a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
CH01AC03/P-115-A# sh ft group summary
FT Group : 14
Configured Status : in-service
Maintenance mode : MAINT_MODE_OFF
My State : FSM_FT_STATE_ACTIVE
My Config Priority : 200
[code]....
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
I have been looking for the command to view all concurrent active connections or sessions on our Cisco 2911. I want to see what the total connections or sessions are at peak times throughout the day.
View 4 Replies View RelatedWe have an ACE 4710 that has two web servers in an active/passive scenario. The issue is that if node 1 fails and node 2 takes over connections to node 2 stay active even if node 1 becomes available again. Is there are way to ensure that node one is not placed back into service if it becomes available again.
how active/passive failover shoudl be configured, so I can make sure I have it set up correctly;
I am completely new to the Cisco ACE devices but have been asked to look at deploying them. I have read the ACE virtual partioning paper which covers the ACE module, and it mentions the following;"In an active/active high-availability design, both the primary and backup Cisco ACE modules are active simultaneously. The active virtual partitions are distributed across both modules, such that approximately half are active on the primary module and the remaining are active on the backup module."does the same resilience model work the same using the Cisco 4710 appliances? I.e. can we split virtual partions across two physical devices thereby having an active/active scenario.
View 4 Replies View RelatedWe have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
View 3 Replies View RelatedIs this normal to have millions of current connections within an ace 4710? There is only 3 current connections but shows a high number?
View 3 Replies View RelatedI have four ACE 4710. Each pair of ACE is in one geographical location. Probes are configured so that it is checking regular regex (HTTP GET).When there is need rserver update we change text in our testpage.html (for ie. from "OK" to "SUSPEND" ) so that probe detect fail. In fact rservers are still operational, but should not accept new connections. This works fine. BUT I observed that established connection/sessions did not end up after probe fails. ACE probably wait for openned/established connections to end up and it is what I am askign for.What happens if probe fails but in fact rserver is operational? I thought that if probe fails it also end up/cut all established connections to rserver. But seems it is not true.
View 2 Replies View RelatedWe are using a sticky serverfarm with 2 real servers, one server was down for maintenance for an extended period of time. When it came inservice again it was not getting any connections. is it because all the connections had stuck to the other server ? we want sessions to be sticky but we also want to LB?I got it working by bouncing the server that had been online all the time. things started to LB then.BTW the ACE 4710 is running 4.2.1
View 1 Replies View RelatedI must redirect all connections from port 443 to 9443.
this is configered and running:
serverfarm host FARM-002
probe test-xml
rserver svx-xmlfw-lb-01 9443
backup-rserver svx-xmlfw-lb-02 9443
inservice
rserver svx-xmlfw-lb-02 9443
[code]....
I have in the moment following problem. All connections become redirectet to port 9443 but port 8080 shouldn`t be redirectet to port 9443. What can i change in my config to solve this problem?
We are using a ACE 4710 with A3(2.6) software release.I had to change our sticky load balancing method for HTTPS to cookie based.However while connections appear to work if I look at the show sticky database table I can not see or confirm sticky entries for the cookie based connections.Here or config snippets to show the config
sticky http-cookie ghh-www scook-ghh
cookie insert browser-expire
serverfarm ghh-www-443
class-map match-all ghh-www-443_CLASS
2 match virtual-address 172.16.1.21 tcp eq https
[code].....
our application team is mandating, that the solution we should come up with for SLB, should support Active/Active mode of SLB operation.
My question, is this mode of operation supported/accredited by Cisco, and what is the draw back from the traditional active/standby.
I have the following drawback was held on autodicovery on a CiscoWorks LMS 4.0 which captured all the IP's of the devices on the network between these found a LAN segment that connects to all devices, when creating this view for the Campus Manager appears a LAN segment and We don´t want to appear there on the views, can you edit the view and delete this segment of the map. or if it is necessary to rediscover again.
View 2 Replies View RelatedReport run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View RelatedI have an application for work that I need to access true vpn connection :I have Sbs server 2008 with vpn support , I can access my folders and exchange and ... , this works fine.Now I have an application that search to connect to the server via local ip at work but when I use vpn to access it then the application goes searching on my local ip adress and not on the vpn ip adress.vpn has same ip as local ip at work).Now my question is: Can I set the application to search on the range of my vpn connection instead of searching on my local ip when i am not at work but on a different site ?I tryed almost anything but the application still looks directly on my local ip instead of the ip of my vpn
View 8 Replies View RelatedI just recently got the internet and I have a desktop computer that has ever rarely been used and it has never had the internet on it. I called tech support of my ISP to see what many be the problem why I can't connect to the internet and found that the source of the problem was I do not have a LAN network connection. When I open Network Connections on the computer, nothing is there. I also went to device manager and there is nothing there for Networking. Under category of "Other Devices" in Device Manager there is a question mark next to "Ethernet Controller". Are there drivers or something I need download to fix this so I can connect to the internet via a DSL connection.
My computer specs are:
Windows XP Professional
Version 2002
Service Pack 2
[Code].....
my home pc doesnt have any desktop icons or a toolbar and so i am unable to connect to the internet.could tell how i could connect to the internet using task manager
View 6 Replies View RelatedI'm working on a small scale Cisco WAAS deployment. I want to know if it's possible to use the entry level Cisco WAVE-294-K9 as Central Manager.Also about licensing, does this appliance model come with the enterprise level license
View 2 Replies View RelatedMy Ethernet is not showing up in device manager or Network Connections. I've checked the bios and it is enabled. I've also tried to install the drivers, but at the end of the install this error message pops up " the Realtek Network Controller was not found. If Deep sleep mode is enabled please plug the cable"
View 1 Replies View RelatedI put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.
View 4 Replies View RelatedI'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool. I don't see a GUI as detailed in the document: url...How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?Having read through copious amount of documentation I can't seem to find a refrence that would ne useful here. This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?
View 2 Replies View Relatedi'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?
View 2 Replies View RelatedI have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.
View 1 Replies View RelatedWhat are these ports used for? What can I do with them?
View 2 Replies View RelatedI am trying to configure sticky on an ACE 4710 and don't understand what the netmask part of the sticky ip-netmask netmask address {source | destination | both } name command.
Some examples use 255.255.255.255 and others use 255.255.255.0 but I don't know what the significance is or what it does?
I am going to configure for both source IP and destination IP (both).
With the current (A5) ACE 4710 lic setup, does the "X gigabit per second appliance throughput" that is licensed affect: -
A) Only "appliance" i.e. load balancing traffic, any other normal routed traffic is not included in the limit
or
B) Is it an overall throughput limit on the interfaces i.e. includes all traffic not only load balancing traffic but also normal routed traffic crossing the appliance
Looking at a scenario where the lic size I need for HTTP load balanacing would be one size if A) but would need to be much larger is B) to accomodate out of hours routed backup traffic crossing the ACE 4710
I've just run the ACE 4710 and it seems that is booting up well but it stops when 'Setting up dynamic memory size' message appears.
INIT: version 2.85 booting
b4 lspci
1 Cavium device(s) found.
[Code]....
I've got a web app that the owners want to run over port 80, but also using SSL to secure private data in transit. The architecture is an ACE 4710 in SSL termination mode->Apache (port 2000)->Back-End app server.
I've got two VIPs set up already - one on port 443 and one on 2000 - both of which do the SSL termination quite nicely, but using the 3rd VIP set up on port 80, the connection steadfastly refuses to be HTTPS (i.e. doesn't show the padlock).
I've done all the set-up through the web interface so far, can this be done? If so, how?
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
[URL]
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
View 3 Replies View Related