Cisco Application :: ACE 4710 Failed Probe And Established Connections
Jan 23, 2013
I have four ACE 4710. Each pair of ACE is in one geographical location. Probes are configured so that it is checking regular regex (HTTP GET).When there is need rserver update we change text in our testpage.html (for ie. from "OK" to "SUSPEND" ) so that probe detect fail. In fact rservers are still operational, but should not accept new connections. This works fine. BUT I observed that established connection/sessions did not end up after probe fails. ACE probably wait for openned/established connections to end up and it is what I am askign for.What happens if probe fails but in fact rserver is operational? I thought that if probe fails it also end up/cut all established connections to rserver. But seems it is not true.
I want to configure my ACE so that if a probe fails, it fails over to the backup rserver, BUT it won't failback to the primary rserver until manual intervention is complete. The problem is we don't want an rserver to fail and failover to secondary, then failback to primary, repeat... (flip-flopping). I want to be able to have time to get on the server and find out what may have caused the probes to fail before it fails back.
We have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin# license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]
We are using a sticky serverfarm with 2 real servers, one server was down for maintenance for an extended period of time. When it came inservice again it was not getting any connections. is it because all the connections had stuck to the other server ? we want sessions to be sticky but we also want to LB?I got it working by bouncing the server that had been online all the time. things started to LB then.BTW the ACE 4710 is running 4.2.1
We are using a ACE 4710 with A3(2.6) software release.I had to change our sticky load balancing method for HTTPS to cookie based.However while connections appear to work if I look at the show sticky database table I can not see or confirm sticky entries for the cookie based connections.Here or config snippets to show the config
I have a problem in the ACE 4710. In view of the connections of a web environment. When I view connections on Config> Operations> Real Servers, Conns column values appear very high connections (Example. 1606317769078).Already in Config> Operations> Virtual Server the number of connections appear normal. Version 4710 ACE Device manger A4 (2.1a)
I have an RDP server farm that lost a disk. The RDP service was still running but users were unable to log in. I'd like to create a health probe that does maybe a combination of TCP probe for port 3389 and something that can determine if the drive that stores user profiles is available.
I cannot add any new service (http or ftp) to the server. Is there any way I can check SNMP mibs on the windows server or maybe WMI through TCL?
I have a physical server running behind the ACE module ACE20-MOD-K9. The Server has several virtual machines. One of that virtual machines, has a WEB SERVER running virtual https servers. For example, server with IP address 10.0.0.20/24, has serveral virtual HTTPs servers as of urll... So, if you nslookup the servers, they all respond with 10.0.0.20 IP address. So if I do url...goes to 10.0.0.20 and read the VIRTUAL SERVER config and replies back to the request.Now, I am trying to verify that the TCP connection (443) and the HTTPS server itself is up and running but only for the url... site and not for the other 2.The problem that I am facing is tha the HTTPS probe fails randomly. The TCP probe works fine.
Using Cisco IOS 12.x+ on a router.How would create an ACL that will only allow access to a port from the inside only after it has been established. i.e. similar to port triggering? Inside host 10.1.1.60 needs to use port 61200 for bit torrent. Dont want the port to be visible as open to the global net accept when the host 10.1.1.60 establishes the connection first.That way a port doesnt have to be left open 24-7.
I have one ASA5520 with version 8.4(3), and a few ACL rules defined. One ACL is permit traffic from one interface(EXT_SERVICE) to another interface(DMZ_SERVICE), if i change that rule to deny traffic, all new connections that match the rule is denied, but no the established connectios. ¿Why the established connections can pass the deny rule? ¿How I can change that? I need create a ACL with deny type and stop all comunications that is running and match the deny rule.
Running-config of my ASA5520:
ciscoasa# show run : Saved : ASA Version 8.4(3) ! hostname ciscoasa enable password 8ay2wjIyt7RRXU24 encrypted passwd 2wFQnbNIdI.2KYtU encrypted names ! interface GigabitEthernet0/0 [Code] ........
Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
I've got a problem with Cisco ACS 4.2 authenticating Cisco 4710 ACE appliance.
ACS4.2 has been configured to use both internal and external database. It's been working fine for a couple or years.
Recently we bought a Cisco 4710 ACE appliance. When I use ACS4.2 internal username and password to login the Cisco 4710 ACE appliance, I have no problem. I can also see the passed authentication log on ACS4.2. However, if I use AD username and password, I couldn't login in. The message is "Login incorrect". I checked the failed attempts log on the ACS4.2, there was no log regarding the failed attempt. My AD username and password works fine on all other cisco routers and switches.
I've posted my AAA configuration of the 4710 ACE below. ACE is running on the latest version A4(1.1).
tacacs-server key 7 "xxxxxxxxxxxxx"aaa group server tacacs+ tac_admin server xx.xx.xx.xx
aaa authentication login default group tac_admin local aaa authentication login console group tac_admin local aaa accounting default group tac_admin
i'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?
I have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.
With the current (A5) ACE 4710 lic setup, does the "X gigabit per second appliance throughput" that is licensed affect: -
A) Only "appliance" i.e. load balancing traffic, any other normal routed traffic is not included in the limit
B) Is it an overall throughput limit on the interfaces i.e. includes all traffic not only load balancing traffic but also normal routed traffic crossing the appliance
Looking at a scenario where the lic size I need for HTTP load balanacing would be one size if A) but would need to be much larger is B) to accomodate out of hours routed backup traffic crossing the ACE 4710
I've got a web app that the owners want to run over port 80, but also using SSL to secure private data in transit. The architecture is an ACE 4710 in SSL termination mode->Apache (port 2000)->Back-End app server.
I've got two VIPs set up already - one on port 443 and one on 2000 - both of which do the SSL termination quite nicely, but using the 3rd VIP set up on port 80, the connection steadfastly refuses to be HTTPS (i.e. doesn't show the padlock).
I've done all the set-up through the web interface so far, can this be done? If so, how?
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
If we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
I am new to the 4710 appliance.Apart from the 4 GE 'data' ports, there are 2 Ethernet 'management' ("console") ports. I find the description in the "quick start guide"somewhat confusing. URL, Is a first-time serial connection (at least to run the initial config. script) mandatory? Or can you obtain the same result via one of the 2 Ethernet management ports and using a default ip address (192.168.1.10 ? When running the initial config. script (only possible from the serially connected console i suppose), you have to select your management port. Why does the system in step 5 proposes you 4 ports, and not just 2? I suppose the intended port for management is one of the 2 management ports, not one of the 4 data ports?
I have a pair of ACE 4710s with 12 contexts sharing the load, running A4(2.1). esterday I upgraded one of them to A4(2.3) now I cannot telnet to the Admin context.Pings ok. I can telnet to other contexts on the box and everything seems to be working ok when i do a " sh telnet" comes back with
No Session Information is available sh telnet maxsessions telnet maxsessions 16
ACE# sh script code NORDICID_PROBE.Error: Called API is invalid or non-existant.Hardware is ACE-4710-K9 and software A3(2.7)The probe itself is functioning ok according to show probe detail.However show script script_name probe_name -counters all remain at zero for some reason. This wasn't the case on the previously use ACE software.To my recollection the command show script code has worked successfully before on the same ACE software. Not 100% sure though, but it definitely worked on the previous software we ran on the ACE.