I have been given a task to upgrade 8T1's bundle to DS3 Fractional circuit. We are currently using 2821 router with 4 VWIC-2MFT. What card/module I need to order for upgrading to fractional DS3. Also are there any compatability issues with ISP or local router.
View 6 RepliesBasically I run 3 voice gateways on 2821 routers. In two of my routers I've had fan failures, one router has had two fans die and one has had just the one.
I was going to buy the offical Cisco fan replacement kit but then I thought with such as high failure rate I'd rather buy something else and better guarentee the service to my call centres.
So, what i'm asking is:
- Is there any reason why I cannot procure a standard 80mm 12V fan with a better rating (cooling and reliability) and install this in my 2821's?
I understand this may invalidate any warranties but mine have long expired.
I have a new fresh 5508 release 7.0.98.0 When I try to download (I mean upload to the controller) a customized Webauth bundle in .tar format I have the following message error in the syslog :*TransferTask: Oct 29 12:56:08.894: %UPDATE-3-UNTAR_CMD_FAIL: updcode.c:2832 Error during untar of webauth bundle. Tar returned 256.
View 17 Replies View Relatedhow can i remove webauth files from WLC?I have few versions of login.tar file used for web-authentication. After uploading a new login.tar file, the wlc still show old webauth bundle files. I tried to remove customized webauth login from wireless LAN, issue clear webauth-bundle and show>custom-web webauth-bundle WebAuth Bundle does not contain any files but when i upload new login.tar that does not include files from previous login.tar, i still get the old webauth. Is it possible to delete extracted webauth files from the controller using CLI?
WLC is running 7.0.116.0 code.
What is the command that can show the ACE Bundle (Like: ACE-4710-02-K9, ACE-4710-04-K9). We have ordered one ACE with 4G BW, and another one with 2G BW. But nothing shows this fact using "show hardware" and "show inventory" commands !
View 1 Replies View RelatedI need to understand security bundles. I purchased a Cisco Security Bundle, Advanced Security, 64F/256D. part number CISCO3825-SEC/K9. My expectation from this device was that I will get an IOS based firewall with no need for an additional firewall module. however, the supplier is telling me that I have to buy a firewall module to use the feature. Isn't the bundle supposed to come with all I needed since is a bundle?
Is there any command I can use to verify if this device is really what I paid for? what can can I check for in the sh inv and sh ver commands? I don't see any information from these commands.
To understand and configuring VPN setup to give secure access to my DB & Application Server exist in my Datacenter, to other Service Provider organisation. They need to access those DB & Application Server sitting at their company LAN itself.
My DC Setup :-
1. Core Router 7609 with SPA-IPSEC-SSC400-1 ( Cisco 6500/7600 IPSec VPN SPA Bundle 1 )
2. Core Switch 6513 with FWSM, ACE, SVC ( Network Analyser ), SUP 720
3. Distribution 6509 SUP 720
All the DB & Application Server connected to Distribution Switch in various VLAN,The Server support team from another company need the access to those, for that we will take MPLS link connecting out Core Router.
I'm going to be wiring a new (to me) house with a couple cat 6 runs to each room. The runs will all be brought back to an enclosed 6u rack and cat 6 110 style patch panel. This rack will contain:
- HP 2824 Switch
- PfSense router (Supermicro X7SPA-HF ITX board)
- DSL modem
Since the rack is completely metal and enclosed I'm going to put my Netgear WNDR3700 WiFi router (used as an access point only) on top of the rack. My question is, what the implications are in regards to placing a WiFi device right next to a bundle of ethernet cables?
We have ordered the following 10 line items , but only got 3 licenses , unless the 3 licenses somehow have all the licenses integrated into the 3 part numbers below, but I suspect not.
Licenses attached from Cisco:-
N7K-C7009-XL-SBUN Nexus 7009 Scalable Feature License x 1
N7K-C7009-SBUN-P1 Inc LAN,ADV,TRS,EL2,DCNM,DCNMSAN,MPLS,SAN,XL -Promotion x 1
[Code].....
Recectly we replaced Cisco 2100 Series LAN controller to Cisco 5508 Wirless LAN controller , I downloaded WebAuth Bundle from my Old LAN Controller ,when i am trying to upload to my New Wireless LAN controller ,its not uploading and also it gave me uploading failure error message .
View 2 Replies View RelatedI am trying to upload a customized web-auth bundle to a WLC 5508 and having some issues.I have downloaded the web-auth bundle from Cisco and used this as a template to create the web pages.I seem to recall that there is only a couple of Windows tools that you can use to TAR the file such as TUGZIP and IZARC. Anyway I have tried both and I still cannot get the file to extract. I have tried to strip the file out so that I only send up the login.html page and even this does not work.I am using a software release 7.0.220.0.
View 6 Replies View RelatedI'm trying to replace a ASA 5505 with a Cisco 2801 w/ security bundle.I have gone through a pretty basic set up of configuring what I could and letting the Cisco Config Prof do the security audit to lock it down. I have everything working just fine except for the bandwidth.
As soon as I plug the router in it seems to give all the bandwidth to one computer and the rest of the campus slows down to a crawl.I turned on "fair-queue" and even tried the QoS wizard in CCP, but it seems like thats if you want to prioritize voice over data - which we aren't running VOIP so I don't need.
I have in the past downloaded the webauth bundle to a wlc 5508 running 7.0.98 successfully. I am trying to upload a new bundle after modifying the AUP but I get an error after the download to the wlc.
The error with FTP or TFTP is
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log
I've tried to copy the unmodified bundle from the zip and get the same error so I don't think it's the login.tar file.
I have a site which has been successfully running a multilink bundle of four T1 lines for about 6 months. The remote location is a C3825 router and the central location router is a C7206. I have access to both. A few weeks ago the multilink circuit started flapping and I was able to identify one of the four T1 lines as the culprit. When I shut down the interface for that one T1 line, the multilink circuit stops bouncing. As soon as I issue a "no shut" command on that fourth T1 interface, the multilink circuit starts flapping, ping commands start to time out and I have to shut it down again. The Telco has sent a technician to both locations and reported all tests run clean. Internal wiring from the NIU to the router has also tested fine. I've tried to move the T1 lines to different ports on both routers and the problem persists. [code]
View 9 Replies View RelatedI would like to get webauth bundle sample to create custom page for our AP controllers but I'm unable to find the sample .tar within the WCS itself.Some other WCS manuals has references in them that says there should be link to download sample from WCS but clearly 2106 hasn't got one.There's one in download section "webauth bundle 1.0.2.zip" but this is for registered partners and costumers, we are not registered as partners and cannot download the sample ourselves.
View 2 Replies View Relatedhow to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
but, it does not work.
I have a question about Cisco ASA 5505 firewall.We need 3 interfaces on the firewall , "inbound", "outbound" and "DMZ" , to control traffic between these zones.
Can we do this with Cisco ASA 5505 50-user bundle , or do we need to purchase Cisco ASA 5505 Security Plus bundle to get the DMZ zone working.
We have 4 data T1s providing our office with 6Mbs of internet bandwidth.I have been trying to track down the reason(s) for the steadily increasing frame and abort errors on the Multilink interface of our new router.We have a new 2961 with 2 2 port T1 interface cards (VWIC2-2MFT-T1/E1).
At first it looked like the T1s were completely clean, but after diving down a bit the last of the 4 T1s does appear to have a decent amount of slip and error seconds.Is that something that would cause the Multilink interface to show input, frame, and abort errors?Any config or debug commands I should start with to narrow down what might be causing this problem?
Config snippets:
card type t1 0 0card type t1 0 1!controller T1 0/0/0clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/0/1clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/1/0clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/1/1clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!interface Multilink1ip address X.X.X.X 255.255.255.252ip nat outsideip virtual-reassemblyppp multilinkppp multilink group 1ppp multilink fragment disable!interface Serial0/0/0:0description T1 : HCFD-XXXXXXno ip addressencapsulation pppppp
[code]....
I found this reference DCNM-L-NXACCK9 in the configuration generated by a dynamic Tools for a nexus bundle N5K-C5548UP-B-S32. This reference is not reflected in the price list. Has it been replaced? no datasheet on Cisco portal.
View 2 Replies View RelatedI am trying to upgrade a brand new ISE 3395 from 1.0.3.337 to 1.0.4 (latest). It keeps failing with % Manifest file not found in the bundle Here is the output:
company-ise-01/admin# application upgrade ise-appbundle-1.0.4.573.i386.tar.gpg ftp
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Manifest file not found in the bundle
[code]...
I can't find anything about this for ISE, although there are a lot of topics for the same error for ACS.
Is it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?
View 4 Replies View RelatedWe have ordered a N5548UPM-6N2248TP bundle. We would like to know if FET-10G sfp’s are included in this. let me know the difference between N5548UPM-6N2248TP and N5548UPM-6N2248TF bundle.
View 3 Replies View RelatedI have router cisco 2821 wit IOS version 12.4(25d) I also have Cisco AIM-VPN/SSL-2 Encryption Module for this router.I inserted this module in AIM slot 0 but can not see it. [code] What should I have to change to enable this module?
View 2 Replies View RelatedI have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedI have configured Clientless SSL VPN on 2821 router with IOS12.4//Its running fine and I am able to open local portals I have mentioned in the SSL URL List.
View 1 Replies View Relatedupgrading from our current WCS version to 7.0.230.0 (not going for NCS at the moment).
View 4 Replies View RelatedI'm trying to upgrade my WCS from 7.0.164.0 to 7.0.172.0 but it keeps throwing me into the manual process because it detects multiple versions. Seems a previous upgrade from 6.0.132 to 7.0.164 did dot remove the 6.0.132 directory or files.
Am I safe to delete the 6.0.132 directory/files and trying again?
I have a cisco 2821 router and it has an advanceip image in the flash each time on reboot it gives the message software forced crash and checksum error and finally goes into rommon. i tried xmodem and tftpdnld -r but same problem persists. I even changed the CF with a working router's flash but the same problem occurs.I also loaded an ip base image of about 13Mb size and all the same problem repeats with it.
View 10 Replies View Relatedwant to view the Log on the Cisco 2821 router for any issue occur.
View 2 Replies View RelatedI'm trying to install ios into my cisco 2821 which boots in rommon. Apparently the ios is corrupted, I have set the IP_ADDRESS, IP_SUBNET_MASK,DEFAULT_ GATEWAY, TFTP_SERVER, TFTP_FILE but anytime I issue the 'tftpdnld' and confirm to continue, the process will time out give this error message" ARP: address resolution for 10.203.8.49 timed out.ARP failed with failure code 1. TFTP transfer aborted.
View 6 Replies View Relatedi have 2 routers, 2821 and 2811. they are connected via GRE over IPsec, and all of the traffic from 2821 is being routed to 2811 with a default route to its tunnel interface. 2821 needs to access internet through 2811 valid ip address, my question is that how should i nat the traffic on 2811 so that 2821 can access the internet?
View 1 Replies View RelatedI get from my ISP 50 Mbps upload/download link via BGP. I tried to test today the speed by downloading around 10 torrents simultaneously and I use PRTG Network Monitoring to view port traffic speed. According to PRTG Reports the maximum rate of speed I get is 20 Mbps. I use Cisco 2821 ISR on my side.
View 6 Replies View RelatedI have multiple VPN endpoints setup on our Cisco 2821, an SSL VPN, a site-to-site VPN, and a Web VPN for windows users. For whatever reason, the web vpn service periodically fails. The only way I've been able to bring it back up is to reload the router. Is it possible to restart the service itself?
View 3 Replies View Related