I have router cisco 2821 wit IOS version 12.4(25d) I also have Cisco AIM-VPN/SSL-2 Encryption Module for this router.I inserted this module in AIM slot 0 but can not see it. [code] What should I have to change to enable this module?
View 2 RepliesI had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.
Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P32 Gigabit Ethernet interfaces2 Channelized T1/PRI ports <-----------------------------1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.125440K bytes of ATA CompactFlash (Read/Write)
When I do a sho run I see this:
controller T1 0/0/0 framing esf linecode b8zs!controller T1 0/0/1 framing esf linecode b8zs
How do I configure IP interfaces on it though? It doesn't seem to show up as Serial ports on a sho int. Am I doing something wrong?
I'm trying to install LMS 4.0 on a 2008 R2, I got a message saying that this is not supported. Going through Cisco documentation I read the following:
Caution If you want to upgrade the operating system from Windows 2003 or Windows 2008 to Windows 2008 R2, you must first complete upgrading the operating system, and then install the LMS 4.0.x Windows 2008 R2 patch.
I'm a bit confused because i'm not upgrading the operating system, this is a fresh install.
I tried to run this in compatibility mode, selected 2008, and running it as an Admin, this time I'm getting a Locale error stating that this is only supported in US English or Japanese. I've changed the system locale to US English, still getting the same error.
I just got two Prime NCS Servers for my system and they came with 1.2. My management wanted to run the lastest IOS which is 1.3. So as soon as I set the physical equipment up, I downloaded the latest 1.3 IOS for the site and burned it on a DL DVD and reimaged the appliance.
View 1 Replies View RelatedWe've just purchased the a VM Version of MSE (L-MSE-C3-W25) installed on vSphere.Have followed the guide, gone to add this to WSE and it wont connect.Looking at the console it says to type /init.d/msed.start, I get -bash: /init.d/msed: No such file or directory Then type getserverinfo returns Health Monitor is not running.
View 2 Replies View RelatedI have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedI have configured Clientless SSL VPN on 2821 router with IOS12.4//Its running fine and I am able to open local portals I have mentioned in the SSL URL List.
View 1 Replies View RelatedHow can I do a VoIP Install/Repair?
View 3 Replies View RelatedWhich are the cable use during network setup .thr saterlite procedure in transmitting information.The speed of transmission in information.
View 2 Replies View RelatedAny info concerning the installation of CW LMS 4.0.1 on Solaris 10!
The installation keeps on failing when it is checking for packages. Also the second time when we downloaded the software once more.
ERROR: AddProperty called with invalid package name: CSCOmd.
I have also attached the install log files.
The system is Solaris 10 with zones:
bash-3.00# more /etc/release
Solaris 10 10/09 s10s_u8wos_08a SPARC
Copyright 2009 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 September 2009
121133-02, 125503-02, 126897-02, 127127-11, 127755-01, 138866-01 Incompatibles:
[Code] .....
I have one WLC AIR-WLC4402-50-K9 which is hitting some bug. So I done RMA for that devices and now i got the new WLC.Now i want to install that RMA WLC in network. So can any one tell me what is the process for installtion of WLC. I already have the old WLC in working now. Which file backup i need to take from old WLC.
View 3 Replies View Relatedis it possible to install cisco acs 5.4 on vmware 8 workstation ?
View 1 Replies View RelatedI am installing LMS 4.1 to windows 2008 R2 SP1.Server hardware meets requirements.A the end of the installation I am getting from the installation log file the following warnings/errors. [code]
View 5 Replies View RelatedI have installed lms 4.1 on a windows 2008 server however after installation, the webgui cant be launched
View 3 Replies View RelatedI've installed the ACS version 5.2 in a VMware platform and everything seemed fine but in the post installation task I need to access to the GUI. Based on the documentation I should access the "https://10.0.0.X/acsadmin" on my browser's url but after I hit enter nothing comes up, there's just a whiter web page. Is there any missing configuration that I need to do and that it is not on the configuration pages?
View 5 Replies View RelatedWe are getting the below mentioned error while installling Cisco Prime LMS 4.2.1 evaluation version on WIndows 2008 Enterprise R2.We tried installing on a high end VMware server .Prerequisites are all taken care by us.We are getting a LMS installation abort log saying that Swap space is not configured properly even after increasing the Paging size to 32 GB.Our physicalmemory is 16 GB.Hard drive has 2 partitions,one is 35 GB and other is 200 GB.
View 3 Replies View RelatedWhich certificates do I install on the ASA 5510 ???
I have a Trust External CA Root, Trust Server CA, Extended Validation Secure Server CA and the name of the domain all ending in CRT. Yet the instructions only refer to two certificates ?
My company just upgraded our VPN software to use Cisco AnyConnect 3.0.1047. We were previously using 2.5.0217. I successfully upgraded the VPN client on my iMac. I am trying to do the same on my MacBook Pro but the process is failing. Both Macs are using OSX 10.6.7. Both use Chrome but I have reproduced the error using Safari and Firefox on the failing system.
On the failing MacBook, the IP address my IT department gave me produced this error:After the 26 second timeout completed, I was brought to this screen:
I clicked the "Mac..." link above and a file called "cstub" was downloaded. I could not execute the file directly as its permissions started at 644. I changed its permissions through the terminal to 755. I tried executing the binary but it failed returning error code 250.I tried uninstalling AnyConnect 2.5.0217 to see if that improved things. No change.
We would like to install a pair of ACS 5.4 apliance as primary /backup in our two datacentres.I have some question regarding degin.
1- We have 800+ network device to monitor , can we install by range of address instead of instlling one by one in device host database ?
2- Do We have to install all 800 device first on Primary and then again on backup or Primary will replicate to backup server?
3- We do not have real IP address yet, so if we built with dummy address and make them pair and all the database sync, then when we change their IP address, will the distributed primary pair will have any issue with backup ACS server?
I have a cisco 2821 router and it has an advanceip image in the flash each time on reboot it gives the message software forced crash and checksum error and finally goes into rommon. i tried xmodem and tftpdnld -r but same problem persists. I even changed the CF with a working router's flash but the same problem occurs.I also loaded an ip base image of about 13Mb size and all the same problem repeats with it.
View 10 Replies View Relatedwant to view the Log on the Cisco 2821 router for any issue occur.
View 2 Replies View RelatedI'm trying to install ios into my cisco 2821 which boots in rommon. Apparently the ios is corrupted, I have set the IP_ADDRESS, IP_SUBNET_MASK,DEFAULT_ GATEWAY, TFTP_SERVER, TFTP_FILE but anytime I issue the 'tftpdnld' and confirm to continue, the process will time out give this error message" ARP: address resolution for 10.203.8.49 timed out.ARP failed with failure code 1. TFTP transfer aborted.
View 6 Replies View Relatedi have 2 routers, 2821 and 2811. they are connected via GRE over IPsec, and all of the traffic from 2821 is being routed to 2811 with a default route to its tunnel interface. 2821 needs to access internet through 2811 valid ip address, my question is that how should i nat the traffic on 2811 so that 2821 can access the internet?
View 1 Replies View RelatedI get from my ISP 50 Mbps upload/download link via BGP. I tried to test today the speed by downloading around 10 torrents simultaneously and I use PRTG Network Monitoring to view port traffic speed. According to PRTG Reports the maximum rate of speed I get is 20 Mbps. I use Cisco 2821 ISR on my side.
View 6 Replies View RelatedI have multiple VPN endpoints setup on our Cisco 2821, an SSL VPN, a site-to-site VPN, and a Web VPN for windows users. For whatever reason, the web vpn service periodically fails. The only way I've been able to bring it back up is to reload the router. Is it possible to restart the service itself?
View 3 Replies View RelatedWe have around 20 VPN tunnel via Cisco Router 2821 (Intranet) and around 30 VPN tunnel via Cisco ASA (Internet) with 3rd Parties/Vendors.I wanna know if there is any monitoring tools from Cisco or any others providers who can give me information/trend report about VPN tunnel Up/Down time, Volumns of Traffic, Protocols etc.
View 2 Replies View RelatedI have a DMVPN network with 2 hubs (2821's). This setup is used for VoIP applications over the Internet for teleworkers. At the main hub site I used to have only 1 Internet feed which was DSL with a static IP. Now I have 2 WAN feeds for this site - 1 FTTB w/ PPPoE & the DSL with static IP. Since this site also hosts a PRI, I want all voice communications to go through the FTTB link instead of the DSL for obvious reasons, but keep the DSL as DMVPN Hub for all NHRP lookups as this link has a static IP address & is very stable. We originally put the PRI router as a DMVPN spoke which connected through the FTTB link, with another router acting as the DMVPN hub on the DSL link. This was obviously a waste of machinery. I want to combine both routers into one. So I tried something like this (don't laugh):
Gi0/0 to FTTB (Dialer1 connects to Internet)
Gi0/1 to DSL (Public IP towards 877 demarc)
Tun0 attaches to Dialer1 public IP and connects to other spokes, no VRF
Tun1 attaches to Gi0/1 public IP and acts as DMVPN hub (ip nhrp map multicast dynamic) under VRF "Hub"
EIGRP AS 1 is set up twice, once under router eigrp 1, and the other using router eigrp 2 using an address-family under the Hub VRF.This kinda works but obviously Tun0 & Tun1 do not speak to each other. I also had to remove the ip nhrp map instruction that pointed to Hub1 on Tun0, as this was causing a weird condition in the router where it was repeatedly trying to connect a tunnel to itself, and crash the router because the NHRP process would go haywire. So my users must rely on the Hub2 to get a NHRP lookup for the PRI site. If Hub2 goes down, everything works in the network except for tunnel connections to the FTTB link. I'd rather not have to configure 2 tunnels on each spoke router unless I really have to.
URL What changes are needed to the 2821 config that is behind another Cisco router? And what static ports should be opened on the MAIN Cisco router that is in front of the 2821?
View 1 Replies View RelatedI am looking for information on how to properly configure rate limits on a Cisco 2821 so that I can set different Service levels by IP address. For example I want to limit a block of IPs to 1 Mbps Down and 512 kbps Up. I am doing point to point networks from our router (ISR 2821) to another router that is assigned a static IP. The other router connects to our router through a Fast Ethernet port on a NM 16 port switch card. The routing end point for the network is on a VLAN interface. Currently we are using bonded T1's but are about to turn up a Metro-E circuit.
View 1 Replies View Relatedhow many NM modules can be inserted into cisco 2821?
View 3 Replies View RelatedI have 1 2821 router with several IP addresses from a single provider. The IP addresses are not contiguous.I would like to NAT different internal subnets to different external IP's. i.e. map 10.1.1.0 to x.x.220.68 and 10.1.2.0 to x.x.220.70 and 10.1.3.0 to x.x.105.184.
I currently have ip nat inside source route-map SDM_RMAP_1 interface GigabitEthernet0/1 overload that translates everything to x.x.105.184.What would be the best way to setup the NAT statements to be able to divide up the subnets?
I will be getting a WAN connection to a few offices and I have a need to control routes recieved and advertised to/from them. The service provider will be placing a CPE device on-site and will support OSPF with my edge router; in this case a Cisco 2821. That 2821 router will ideally be configured with OSPF routing toward my two core switches.
-> C2821 to NOT have the full routing table from the Core switches
-> Only needs knowledge of two routes from the Core switches and routes from remote offices.
-> Controlled routing advertisements. I do not control the remote offices and would like to ensure they do not accidentally advertise routes into my enviroment that could create a conflict.
I'm assuming the Service Provider will be running BGP on their CPE router, which will mean that the OSPF routes recieved by my Cisco 2821 edge router will be OSPF E2 routes. So if thats the case the 2821 would need to advertise E2 routes.I'm not sure if I should be configuring the 2821 in Area 0...because its meant to be a WAN edge router; but if I configure it in another area...say 200...the Service Provider may configure his CPE router in Area 0...which I'm guessing would pose a problem as the 2821 would be lodged in between two area 0s?
From the reading I've done it sounds like I could use NSSA...but I'm not sure if this is the best design.
Our router 2821 reboots each time vpn traffic is called : - vpn connects without problem - as soon as you launch rdp, ftp or anything else traffic => the router reboots itself Consequence : no more phone, no more internet during the reboot process. A call can be cut when it happens.
Below is the show context log :
CUCME#show context
System was restarted by error - a System Error, PC 0x4046A374 at 10:18:43 CEST Mon Apr 15 2013
[Code].....