URL What changes are needed to the 2821 config that is behind another Cisco router? And what static ports should be opened on the MAIN Cisco router that is in front of the 2821?
View 1 Replies
I am using Cisco configuration professional to set up one easy vpn server on 887-K9,vpn client can dial up the server successfully but can only ping router but on other lan. Looks like there is a nat issues between lan and vpn client?
View 5 Replies View RelatedI have couple of issues with my EasyVPN server and Cisco VPN Client on Win7.
1: VPN Client establishes the connection, traffic flow, destination network can be pinged. After a few minutes traffic stops passing the VPN. No ping to IP or DNS names can be made. In order to resole it. Users have to re-establish the VPN again. Occastioanl it stays and continue to work.
2: VPN Clients don't pick the same IP address from local address pool even though I specified "RECYLE" option in the IP local pool command.
Configuration:
##############################################################################
TQI-WN-RT2911#sh run
Building configuration...
Current configuration : 7420 bytes
!
! Last configuration change at 14:49:13 UTC Fri Oct 12 2012 by admin
! NVRAM config last updated at 14:49:14 UTC Fri Oct 12 2012 by admin
[code].....
I am using 3945E Router as Easy VPN Server, with 15.1 IOS. On router I have bunch on usernames for VPN authentication, I want to restrict Router management access for them(ssh,telnet, http and so on).
View 2 Replies View RelatedOn my 2911 router, can I have both an Easy VPN server, and a site-to-site VPN? Also, with an Easy VPN, is it possible to specify another internet (outside) IP address in my assigned range as the address remote users use . . . rather than the specific IP address assigned to the interface?
View 3 Replies View RelatedCan the Cisco ASA 5510 appliance be used as an EasyVPN Remote device, or only as an EasyVPN Server?
View 1 Replies View RelatedWe have many new and very small remote sites that will be connecting via an ASA5505 using easy VPN. Works without an issue and we've got the configuration and process nailed down.
The challenge I was presented with today involve non-standard remote sites where I need to configure a third interface on an ASA 5505 and allow it to pass directly to the Internet and not go through the VPN. Configuration of the third interface, assignment and configuration of the ACLs / NAT(PAT) are straight forward.
The challenge I face and haven't been able to find a direct answer to is if it's possible to have the traffic bypass the easy vpn network extension process. At this time the traffic is going down the tunnel which isn't what I want.
I fear I'll have to build classic site-to-site VPN configurations which isn't a huge issue though it breaks all maintenance/operations methods, processes and I'll have to spend time training the support team how to detect the differences.
I don't seem to be able to connect to my cisco 831 router with easy vpn server configured using my Blackberry Playbook. Looking at the console of the router i can see the debugging but am not sure what it all means.
Current configuration : 2574 bytes!version 12.3no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!enable secret 5 $1$FM71$y4ejS2icnqX79b9gD92E81enable password xxxx!username CRWS_Ritesh privilege 15 password 0 $1$W1fA$o1oSEpa163775446username shamilton privilege 15 secret 5 $1$wFLF$8eRxnrrgVHMXXC0bXdEGi1aaa new-model!!aaa authentication login default localaaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authorization exec default localaaa authorization network ciscocp_vpn_group_ml_1 localaaa session-id commonip subnet-zerono ip
[code]....
I've two sites, the branch with an ASA 5505 and on the corporate office i've an ASA 5510.I need to make a easy vpn tunnel between this to sites and I've made some configuration, but for now, the ikev1 isn't working.
View 1 Replies View RelatedI have one ASA 5510 on main office that access the internet trought of a private link and one ASA5505 on the branch office that access the internet trought of a ADSL link with dynamic IP.
Behind ASA 5510 the network is 10.8.40.0/24 and behind the ASA 5505 the network is 10.30.103.0/24. I want access both network trought of the frame-relay link and the internet link with EzVPN.I make that access only ip on the main office, this comunication go to frame-relay link and the everyone go to the VPN.When the traffic go to the frame-relay link, I use a NAT Static Policy that change the source 10.30.103.0/24 to source 10.40.103.0/24. Its work OK when a VPN do not UP.When the VPN is UP, the NAT dont work and the packet go to the true IP (10.30.103.0/24).
I have a cisco 2821 router and it has an advanceip image in the flash each time on reboot it gives the message software forced crash and checksum error and finally goes into rommon. i tried xmodem and tftpdnld -r but same problem persists. I even changed the CF with a working router's flash but the same problem occurs.I also loaded an ip base image of about 13Mb size and all the same problem repeats with it.
View 10 Replies View Relatedwant to view the Log on the Cisco 2821 router for any issue occur.
View 2 Replies View RelatedWe are using a 2821 Router as our boundary router. It has installed into it a 9 port HWIC for layer 2 switching as well as allowing the router to communicate on the Network Management VLAN. All of the devices on the Network Management VLAN are segregated from the managed traffic, which unfortunately also doesn't allow them external NTP services. Can the router be programmed as a NTP server so that all of the network appliances can utilize it for NTP from either it's NM Vlan IP address or from a loopback address?
View 3 Replies View RelatedHow to setup option 150 in IP pool on VPN Client.
View 2 Replies View RelatedI have been trying to configure Cisco1941/K9 as Easy VPN Server through CiscoCP.The tunnel comes up but I cannot pass any traffic to the secure LAN (GigEth 0/1). When the tunnel comes up, I can ping the Loopback interface and the GigEth 0/1 interface IPs.
View 21 Replies View RelatedI have a Cisco ASA 5510 and a Cisco ASA 5505. I want to configure the ASA 5510 as Easy VPN Server and 5505 as Easy VPN hardware client.Using either CLI or ASDM.
View 1 Replies View RelatedI'm in the process of setting up a working VPN/Firewall setup on an 881W ISR. I have the firewall, NAT, and VPN working, and I'm able to connect remotely to my router. The problem I am having is that I none of my VPN cllients can connect to the internet. I suspect that my firewall rules may have something to do with this. Let me break-down what I have, and what I want to achieve:
1. My router is setup with VLAN1 (172.16.1.0/24) as the inside zone (in-zone), while my outside zone (out-zone) is FastEthernet4 (DHCP WAN Interface). I also have a guest zone (guest-zone) VLAN12 (192.168.12.0/24) used for my guest SSID wireless, which is NATed to the outside zone.
2. I have my EasyVPN setup using a Virtual Template Interface that terminates at the WAN interface FastEthernet4 (something tells me this should be changed). Should I terminate at VLAN1, or an interface or loopback on VLAN1?
3. I ultimately want the VPN users to be able to conenct to the local resources on VLAN1 only, while being able to get out to the internet. [code]
I have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.
The Cisco ASA has the 50 internal user license with 10 VPN peers.
We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails.
Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences?
This seems to be the issue from what I can see, just need confirmation.
I have big trouble with easyvpn clients access filtering on asaos 8.4.1. I have couple of remote offices with hardware clients (cisco 87x, 88x) configured as easyvpn clients to Asa. Default route in it's routing table pointing to the Virtaul-Access interface (easyvpn connection to ASA), so there is no split tunneling or any kind of nat on the clients. I have ip-telephony deployed across remote offices. This remote offices should be able to call to each other.
On the ASA i have configuration for this purpose:
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
But as soon as I configured it, remote users obtain an ability to access Internet without any restrictions although there is couple of access-lists configured on the outside interface pointing to easyvpn clients. Then there is no same-security-traffic commands i can filter out access to internal and external resources correctly, but remote offices can't communicate with each other
I have setup nat on three sub interfaces but when trying to browse to local servers, such as our web server, that have been translate, we get a prompt to logon to the router. I suspect these internal addresses should not be natted for local users.
View 3 Replies View RelatedI have a Router 2821 with c2800nm-advipservicesk9-mz.124-24.T1.bin and with a Cisco Integrated Service Engine(s) Cisco Unity Express 7.1.1 in slot 1 , this router shows a high cpu utilization.I think is a bug with the IOS , because there is no voicemail configured on the CUE, there is no traffic to the CUE , just traffic from:
- voice calls
- ospf
The ospf is not the cause of the high cpu , because the high cpu utilization appears before I put the ospf proccess on the router.
Support for WIC-2T , we have one 2821 router with wic-2t currently serial link is running with 2mbps and we want to update with 4 mbps
View 2 Replies View Relatedsend an IOS file 12.3 from laptop to router via TFTP?
View 3 Replies View Relatedi am using cisco 2821 router at the edge in my network where the WAN link is terminated.i want to configure Redundancy . So will 2821 support ? If yes what is the another router .Is it the same series or different for redundant configuration.
View 2 Replies View RelatedI have a cisco ISR 2821 router and I want to configure this router as a BRAS (broad-band remote access server).
View 2 Replies View RelatedI have a Cisco ASA 5505 which is setup as an EasyVPN client to e remote VPN concentrator.The Cisco ASA has the 50 internal user license with 10 VPN peers.We just upgraded the license from the base 10 internal user to 50 user license but it has not resolved the problem and only 10 internal users still work, the 11th fails. Does each EasyVPN client on the inside network take up 1 of the 10 VPN peer licences? This seems to be the issue from what I can see, just need confirmation.
View 3 Replies View Related(Router is ISR 1921)This is doing my head in. I am not using NAT, there are no ACLs, there is no split horizon.Here is what I have. It is practically generated by CCP. When connected I cannot ping the loopback interface or the gig0/0 interface, (not to mention anything else).
version 15.0
service config
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname dcsgw1
[code]...
I have a branch office set up with a cable modem and an ASA 5505 as an easyvpn hardware client with network extension mode enabled, and connects to a PIX515E at the headend.I'm working on a separate issue for why the Internet connection drops periodically at the site, but my main problem is as follows.In this location, I have an 1142 LAP. It can boot up, and join the WLC just fine. Performance seems a little slow when it's working, but it works. The real issue is, if the VPN connection drops and reestablishes for any reason, the wireless clients all cease being able to communicate. All wired clients seem to bounce back without a problem.
The access point still shows to be joined to the controller, the access point never goes down, just wireless clients can't access anything any more. If I reload the access point, clients reassociate and continue on their merry way. For now, I am experimenting to keep the connection from dropping, but I'd really like to get it where I don't have to babysit this thing all day and night, and it can rejoin and function normally by itself after an outage.We are changing to this configuration from wireless bridging due to interference and reliability issues - however, I never experienced any similar issues with this particular access point before, so it's not the access point itself.
I am installing 2 ASA 5505s at home offices with dynamic IPs. The EasyVPN server is a ASA585x. I am using the 5505s in NEM mode. I configured a unique DHCP scope on each 5505. I have a dynamic crpto map on the server. I configured unique tunnel groups, group policies and usernames for each site on the server. This seems to work fine. Is it normal to configure unique tunnel groups, group policies and usernames for each remote site?
View 2 Replies View RelatedWhen ASA 5505 was installed we selected Easy VPN Remote. Now we want to disable it. In ASDM we navigate to Configuration > Remote Access VPN > Easy VPN Remote and try to clear the Enable Easy VPN Remote checkbox but it will not uncheck.
View 2 Replies View RelatedSo I have three ASA 5505 firewall. my firewalls we are in the test environment. I read on the net that when you have a situation like in my company where are headquarter and two offices, i should put in each branch office and headquarter one asa firewall and a firewalls should be configured as easyvpn.
VPN server is in headquarter and easyvpn's are in branch offices. i tried everything, but we could not configure them. maybe it's not a problem that in my test environment at my the external interfaces which have static addresses on these three firewalls, respectively serever 192.168.2.1, 192.168.2.2 and 192.168.2.3 client client. I seted firewalls by following the instructions, but does not work
[URL]...
I solved the problem with the server as a remote access VPN. client workstations that are on the 192.168.2.0/24 network can access a local LAN via VPN. But when you put the ASA 5505 firewall. clients on the LAN side of the firewall can not access the VPN. I use software products Cisco VPN Client 5.0.06, but when I create a connection and try to connect to get an error secure vpn connection terminated locally by the client. reason 412: the remote peer is no longer responding.
I using cisco 837 for incoming remote access VPN connections with are working very well but I recently created one outgoing easy vpn connection and I have issue since that time. As soon as easy VPN is up and established successfully I lost remote VPN access to internal subnet.
Where is :
Internal subnet: 192.168.172.0/24
remote VPN pool 192.168.24.2-6
Take a look at config attached and point me at missconfiguration
We are using a 1803 ISR for remote vpn users. They use Cisco VPN clients with the EasyVPN server functionality of the ISR. I would like to restrict the ports/protocols which they can use to the remote network they connect to.
This is the (edited) client config in the ISR:
crypto isakmp client configuration group RemoteVPN key remoteaccess dns 192.168.0.1 domain domain.local pool POOL_1 acl 140 netmask 255.255.255.240,access-list 140 remark EasyVPN ACLaccess-list 140 permit ip 192.168.0.0 0.0.0.255 any
I tried to edit the acl 140 with access rules, but they do not seem to have any effect. If I edit acl 140 with deny ip any any, for example, the remote users can still use any protocol to access the remote network.
