I have setup nat on three sub interfaces but when trying to browse to local servers, such as our web server, that have been translate, we get a prompt to logon to the router. I suspect these internal addresses should not be natted for local users.
View 3 RepliesI have a problem with the command mls qos trust dscp, I used the ios c2800nm-ipvoice_ivs-mz.124-25f.bin but i can not enable dont show me the complete command in the interface Ethernet o Giga. I want to configuring mls qos trust dscp.
View 1 Replies View RelatedI have looked in the books I have (Cisco ASA, PIX and FWSM; ASA 8.0) and googled a good bit but can't seem to find any specific mention of how to do NAT exemption with v8.4. It seems NAT exemption (NAT 0 access-list) was deprecated. Using ASDM, there's no corresponding menu item for this that is obvious.
We have public addresses inside the ASA and want to allow in/outbound connections using these IP's without NAT. The ASA is a 5550.
Short version is we cannot communicate between our subnets.We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc)We have PAT for each subnet to our outside interface. Each subnet NATs out properly currently.I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS.What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces?
View 0 Replies View RelatedI have a cisco 2821 router and it has an advanceip image in the flash each time on reboot it gives the message software forced crash and checksum error and finally goes into rommon. i tried xmodem and tftpdnld -r but same problem persists. I even changed the CF with a working router's flash but the same problem occurs.I also loaded an ip base image of about 13Mb size and all the same problem repeats with it.
View 10 Replies View Relatedwant to view the Log on the Cisco 2821 router for any issue occur.
View 2 Replies View RelatedURL What changes are needed to the 2821 config that is behind another Cisco router? And what static ports should be opened on the MAIN Cisco router that is in front of the 2821?
View 1 Replies View RelatedWe are using a 2821 Router as our boundary router. It has installed into it a 9 port HWIC for layer 2 switching as well as allowing the router to communicate on the Network Management VLAN. All of the devices on the Network Management VLAN are segregated from the managed traffic, which unfortunately also doesn't allow them external NTP services. Can the router be programmed as a NTP server so that all of the network appliances can utilize it for NTP from either it's NM Vlan IP address or from a loopback address?
View 3 Replies View RelatedI have a Router 2821 with c2800nm-advipservicesk9-mz.124-24.T1.bin and with a Cisco Integrated Service Engine(s) Cisco Unity Express 7.1.1 in slot 1 , this router shows a high cpu utilization.I think is a bug with the IOS , because there is no voicemail configured on the CUE, there is no traffic to the CUE , just traffic from:
- voice calls
- ospf
The ospf is not the cause of the high cpu , because the high cpu utilization appears before I put the ospf proccess on the router.
Support for WIC-2T , we have one 2821 router with wic-2t currently serial link is running with 2mbps and we want to update with 4 mbps
View 2 Replies View Relatedsend an IOS file 12.3 from laptop to router via TFTP?
View 3 Replies View Relatedi am using cisco 2821 router at the edge in my network where the WAN link is terminated.i want to configure Redundancy . So will 2821 support ? If yes what is the another router .Is it the same series or different for redundant configuration.
View 2 Replies View RelatedI have a cisco ISR 2821 router and I want to configure this router as a BRAS (broad-band remote access server).
View 2 Replies View RelatedI'm using a Cisco 2821 router to provide temporary Internet access for a private network of about 300 users for a conference at a hotel. The hotel has provided me a public IP address for the WAN side. On the LAN side I have a 10.x.x.x /8 subnet with the router providing DHCP and NATing (overload) across the WAN interface.
Users can pick up an IP address and access the web. Light web pages such as Google tend to load without issue, however if a user does something that takes more time, such as streaming a Youtube trailer or opening an RDP session, the connection will freeze.
It doesn't appear to be related to bandwidth availability. Pings return on average 10-15 ms. However, I will get a request time out about every 10th continual ping. Steaming video will load about 4-6 seconds worth of data, then will appear to freeze without dropping. Doing something like speedtest.net will send a large amount of data then will hang, without ever ending the conversation.
This doesn't happen when I plug a laptop directly into the hotel public Internet line. They also don't have issues with their network similar to this.
I do not have any ACLs, etc. loaded. The router is basically wide open as far as I can tell. I don't see the router resources getting used much at all.
Recently I have bought a 2821 router from an auction. The router did have some configuration and password on it. I tried to break into it by restating it and pressing control and pause break signal. Old cisco method. Now when I try this method on my 2821. It does say that password recovery is disabled on the router. After this message router proceed with normal boot process. How to break the password ? Even if I loose the configuration.
View 4 Replies View RelatedI want to clear the keys on a 2821 and generate new ones using the command crypto key zeroize command but I don't see this command available as an option. Below is the output of the available options..
ROUTER#crypto key ?
lock Lock a keypair.
unlock Unlock a keypair.
[Code]....
Currently I'm looking for a way to failover our internet connection from one site to another site over our MPLS line, should that internet connection go down.
My layout: Internet > Cable internet modem (Site B) > ASA 5510 (Site B) > 2821 Router (Site B) > MPLS Line > 2821 Router (Site A) > ASA5510 (Site A) > ISP provider internet router (Site A) > Internet
Facts:Site B is the one with the internet issues.The MPLS line is routed using BGP. [URL]
I am sitting on Internet and want to copy IOS Image to router. I can SCP, itu authenticated to Router but ends with a message "host is not communicating for more than 15 seconds".
Router : Cisco 2821
Current IOS: (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1.
I am looking to find the correct router for a 50 Mbps Ethernet connectin that is for Internet traffic. It will need to support 50 Mbps throughput, along with routing protocols for BGP, and maybe NAT/ACL's. It most likely will be a used router, in the 2800 series. I'm thinking a 2821 would work, but need to make sure before I pass it on to the customer. They currently have a 3660 they were thinking of using, but I think it would be too weak, and probably only pas 30Mbps at the most before it chokes. They are a mini ISP with their own ASN, Tier 3.
View 3 Replies View RelatedI have a cisco 2821 router configured as a CME version 7.1. Now I want to upgrade the IOS to version 15 to get a CME version 8.6 but I faced a problem that the flash of the 2821 is 64MB and the IOS version 15 required flash 128MB. I tried to replace this flash with another 128MB installed on Cisco 2811 router but when I installed the 128MB flash on the 2821 CME the 2821 didn't boot from it.
View 5 Replies View RelatedI have Zone Based Firewall running on a 2821 router and would like to configure Url Filtering with Websence . IOS running on that device is c2800nm-adverterprisek9-mz.150-1.M7.bin . Once you have ZBF config you cant configure url-filtering using classic way ( ip inspect ) and this has to be done using class , policy maps .For this to to happen it is required to have match protocol http command under the class map , it wont work using the match access-group command.[code]
Once I put match protocol http command browsing becomes dead slow , also without using match protocol command I cant continue to configure Url Filtering . Is this a problem related to IOS where match protocol command isnt working fine . I have checked CPU utlization of Router and it was roughly near 7 percent .
I am looking for a simple router recomendation for multihoming dual 100Mbps internet connections with BGP routing. What are the current best practices regarding required resources for the full Internet BGP routing table? We were thinking of specing a 3945 for this application, but is that overkill? The customer has a 2821 that is not in use, I'm thinking this would be too slow for Internet BGP routing combined with the 100Mbps line speed.
View 4 Replies View RelatedYesterday my router was hangs and my services was stuck. I start the router hard booted and it works fine.This was second time i was facing this kind of scenario. The attached are the "show tech support" of the cisco router 2821.
View 2 Replies View RelatedI have a 2821 Router, with a VWIC2-2MFT card in it, with two T1s going into that card. The two T1s are a bundled MPLS line.
I then have a cable modem connection going into the gigabit Ethernet GE 0/1 port on the router.
Right now, the cable modem provides a backup connection in case the T1s go down.
What I was wondering is if there was a way to 'combine' the bandwidth from the two T1s with the cable modem?
Any list of dynamic protocols that support BFD, 2821 router support for BFD dynamic routing protocols
View 3 Replies View RelatedBasically I run 3 voice gateways on 2821 routers. In two of my routers I've had fan failures, one router has had two fans die and one has had just the one.
I was going to buy the offical Cisco fan replacement kit but then I thought with such as high failure rate I'd rather buy something else and better guarentee the service to my call centres.
So, what i'm asking is:
- Is there any reason why I cannot procure a standard 80mm 12V fan with a better rating (cooling and reliability) and install this in my 2821's?
I understand this may invalidate any warranties but mine have long expired.
I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
We've got Cisco 2821 for our 90mb/s Internet Access. Its CPU usage is around 80%. Show process cpu does not show any cpu proccess with high utilization. But we have got plenty of policing configured for our clients using policy maps. Can this policing affect cpu usage?
View 1 Replies View RelatedI have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
I am currently running a 2821 to terminate vpn links from all our branch offices over a WAN. I need to add a second interface in order to facilitate a move to a different WAN provider. seeing as the 2800 models are EOL I was looking for an upgrade. My local retailer wants to sell me the following:CISCO3925E-SEC/K9 IS Router 3925E security bundle SEC license pack,HWIC-2T 2 port serial WAN card,MEM-3900-1GU2GB Upgrade to 2GB 1,now my question is why can't i use the 2900 models in order to save some money?All I need is a router that will accept 2 different incoming WANs and the ability to create vpn tunnels over them..
View 19 Replies View RelatedWhat is the best way to monitor an Internet Edge router from the Internal network behind the Firewall?We want to pull more information from the edge router like netflow. We can use SNMPv3 and ACLs to keep the router secure.
But I am looking for the best config to keep both the router and firewall as secure as possible while still allowing us to monitor performance and faults.I am running an ASA and a 2821.
One of our client wants to know "How many route entries a 2821 router or 881 router can support" Such as the 3750 can support 11k routes in ‘desktop routing’ mode. But I want to know the limitations on routers.
View 1 Replies View Related