I am building a BOM for a customer and I need to present cheaper options than 3500 or 3600 APs. I thought of these two models but I don't know what models of antennas to pick.1602 is a 3X3 MIMO with 3 antenna connectors. How many 2.4 GHz and how many 5.8 GHz antennas should I pick for each radio?2602 is a 3X4 MIMO with 4 antenna connectors. In this case I suppose there are 2 connectors per radio.
View 9 RepliesWe ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies View RelatedI need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
View 2 Replies View RelatedMy customer wants to buy AIR1242AG with 2.4 GHZ antennas which are not ceiling mounted. How many 2.4 GHz antennas I can have on the AIR1242AG?
Can I have a recommendation which antenna I should use which is not ceiling mounted?
My desktop PC which has an Asus PCE-N13 Wireless Adapter with two stock SMA antennas receives a very poor signal due to the significant distance between my desktop and the router.In order to improve my signal strength, I thought about buying better 3rd party antennas and specifically external ones which I could place closer to the router that connect to the SMA connections on my wireless adapter via a wire. There's many of these antennas for sale I see, but I'm unsure which is best suited for my situation.
View 3 Replies View RelatedIs it possible to use external antennas on AP541N set in WDS mode? I would only need to use 802.11g mode 54mbps.I believe that the antennas shipped with the access points are removable RP-SMA.
View 3 Replies View RelatedI am expanding coverage in a big outdoor area.Most of the area is covered with AP1552 with AIR-ANT2506 5,2 db antennas.At the border of the area i have some masts where i can place ap's.Would it make sense to use directional antenna's there? I have a big open area where it is not possible to place ap's.The only placement is a mast in the middle of the area.I have a AP1552 with 5,2 db antennas there.Can i get better coverage if i place 3 or 4 ap's with directional antennas ?Or should i try with a 12dBi AIR-ANT24120 ?
View 2 Replies View RelatedI´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies View RelatedI have an existing 1242AG AP in a remote location, I have full access to it. I have a new 1242AG that was ordered but the client forgot to order antennas for it. Is there a way I can find out the exact model of antennas that are connected to the in place AP at the remote location??
View 2 Replies View Related1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
I have not done the firmware for the units yet but have had only 1 outage thus far (but I think it was a power issue over the weekend).What I have done, 3 weeks ago, is put external antenna's on the 2 units which are 15 feet apart at 15dBi.The output is 40hz and I changed the latency time settings on the main unit, leaving the secondary at factory.This seems to be working for me so far. Usually goes down over the weekend and have to reset Mondays,but not this week. I am afraid of running the firmware because then it may become unstable again.
View 6 Replies View RelatedI have a question about external antennas on an access point. I have to plan a wireles solution, that also includes coverage in the industrial freezers. The freezers are one part of the sotck rooms, so the general coverage will be done with 1602I access points.
Since there are quite a lot of freezers in one location, installing separate AP in every freezer will be very expensive. I wondered if there is a possibility to put one 1602 access point with external antennas outside the freezer and then extend the antennas with 2m cables inside different freezers (1602E has three external antennas, so one antenna to each freezer).
Would this installation even work?
The freezers are quite small rooms maybe 2-3m2 sow the coverage is not a problem. But does this installation support multiple clients per AP in different freezers doing stocktaking with handheld terminals?
I would like to install three antennas (2450S) on some AP1261 that i wold spread out 10 feet apart. I am not able to get the antenna on the C connector to transmit. I am not using 802.11N. This is for a warehouse where all the WiFi devices are 802.11G. My question is: can you get all three connectors on the AP to transmit.
View 8 Replies View RelatedMy pc isn't picking up any wireless connections even if they have no pass on them. I don't know what the cause is I trouble shooted my wireless network connection driver 3 times I uninstalled it and reinstalled it and nothing happened. Updated it too. I even tried doing a roll back but still nothing. And when I checked the driver it says device working properly. I have a Toshiba satellite, windows xp.
View 13 Replies View RelatedWhat is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.
View 1 Replies View RelatedI'm working in a campus environment that has an existing wireless network using a Cisco AIR-WLC2112-K9 controller.There are 8 AIR-LAP1242G-A-K9 access points connected to the controller. Each access point has a 5.0GHZ 4.5dbi Cisco omnidirectional antenna, although the AP only supports 2.4GHZ.
Q1. Why a 5.0ghz antenna might had been used with a 2.4ghz AP, and if we can expect increased performance if we replace the antennas with 2.4ghz ones?
Q2. On the controller, the antenna gain is set to 0 for each AP. Is there also a benefit to leaving that 0 as opposed to 9 for 4.5dbi?
I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:
• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?
Antennas were set aside prior to device installation, and now can't be found. Can they be ordered as a replacement kit?
View 3 Replies View RelatedI just recieved new 7921 phones. I cannot get them to pick up a dhcp address
I keep getting DHCP "Timeout's" and " Configuring IP" . The ould 7921's and the new 7925's work just fine. I have tried removing and reconfiguring the WLAN and Interface on the Controllers. I even removed and reconfigured the DHCP scope in Infoblox.
I just installed a new video card so this is probably the problem it says i might have disconnected a wire there or maybe its just a driver if its a wire.
View 1 Replies View RelatedI have changed to Sky wireless router but my MV35-202 wont pick up the wireless signal.it was okay with virgin media.
View 1 Replies View RelatedI have an older Dell Desktop (Dimension E310) with Windows XP. I haven't turned it on in a year or so. Last time I used it I had a PCI Adapter for wireless and it worked fine.
Since then we've moved and are relying on a wireless router and I'm now trying to reconnect it, but it no longer has the little wireless icon. It has the Intel PROset for wired connections (from when I first bought it), and I ran the diagnostic on it, and everything passed except for the "link test." What do I do now?
My netbook have decided to stop pickingup the wifi in my house. My parents laptop picks it up and my iPod picks it up but for some reason it won't pick it up any more?
View 1 Replies View RelatedI have recently bought a second hand toshiba tecra laptop, i am trying to connect it to my netgear router. There is currently only one other laptop connect to this router and yet it will not let me connect to it. I have matched all the setting from the current laptop to the one i am trying to connect however it still will not even pick up a signal. I have phoned my network provider and they couldnt manage to find out the problem. When i try to search for wireless network connections there are none found even though the wifi button is on?
View 1 Replies View RelatedJust made a fresh computer, installed Win98 (have only 128 ram so no XP) I have a card I put in the computer from Linksys which allows for a desktop to have wireless internet. I installed the Linksys software. (first thing I've ever installed on this Computer after Windows) It doesn't pick up the wireless signal in the house (my laptop does just fine).. is there another program floating around somewhere?
View 2 Replies View Relatedi would like to pick up wireless internet using my linksys router is that possible?
View 1 Replies View RelatedI'm just building my gaming computer and have to start figuring out how to get internet on it. Considering I don't have a modem in my room, I would need a wireless card, right?
View 3 Replies View RelatedRecently got satellite high speed. Am trying to hook up the wireless router my son gave me. Installed and set up but my PC doesn't recognize it and my phone won't pick it up.
View 2 Replies View RelatedMy laptop will work on a wired connction just fine, however it fails to pick up wireless internet signals. It will either not find the signal, or not connect to it unless I have my laptop wired with an ethernet cable. My network adapter is a Broadcom 802.11n. I have tried updating the driver, and multiple different routers/connections.(Yes the adapter is enabled to search for connections, it just doesnt find them unless I have it wired)
View 1 Replies View RelatedI got high speed internet last week and have very little understanding of networking. I think I need either a Wireless Access Point, Bridge or Converter. What I'm trying to do: I currently have a Linksys E1000..I have two computers that access this point via built in adapters in the computers. In another room are my gaming consoles and television that I would like to hook up to the internet as well. Is there a wireless adapter that will pick up my Linksys E1000 signal and let me plug ethernet cords into it so my consoles and television can access the network?
View 2 Replies View RelatedI have a Netgear RangeMax Dual Band Wireless-N Router (WNDR3000). It works great in the house. What I would like to do is to be able to use my computer out by my pool. The furthest I can go with my laptop is sitting in a chair right outside my door step. If I walk away from the house, no cigar. Is there a way to extend my internet reception beyond my doorstop?
View 12 Replies View Relatedi have lenova laptop. it does not pick up internet by wireless or through wired connection though the wireless is on?
View 3 Replies View Related