I need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 RepliesWhere I live there is no DLS or cable to probide me with Interent access so I use my Verizon 3G/4G smart phone (Android) as a hotspot. Right now I am using an old Vista PC and ICS (Internet Connection Sharing) to provide Interent connectivity to my home network and Cisco lab. This works fine but I must have my smart phone near the PC for it to work. When I go to other rooms, I end up missing calls and texts since I have t oleave the phone if it is providing Inerent access at that time. If I can get the Airnet's to connect to the hot spot AND provide Internet access, that will provide me additional mobility. This would also be good for small businesses as a backup Internet Connection.
Is there any way that I could elimanate the Vista PC and have my Aironet 1231G Wireless router(s) automatically connect to my phone's 3G hotspot to provide Internet access to my lan?
I have 2 Airnoet 1231G's running the c1200-k9w7-mx.123-7.ja IOS and a C3550XL layer 3 switch.
We have 12 - AP-1231G access points in our warehouse with 2 SSID's, both on different VLAN's. We would like to set one of the VLAN/SSID 's to use DHCP from a windows DHCP server.Is this possible to do with option 43 or is that only for lightweight AP's ? Sho ver: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8).
View 2 Replies View RelatedI have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedI am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
anybody with 2 x rack mount kits for a SRW208P that they don't want? I need to rack mount these devices but my predecessor very wisely decided to throw them out and Cisco does not sell the racks as a separate SKU.
View 1 Replies View RelatedI am still new to wireless. I have been studing for my CCNA Wireless for about 6 months now so I still have a lot of questions.
Right now I have to deploy some new APs. We are using 3502e APs. I have a qustion on how to mount antennas for these access points. I have to make a mounting bracket the new installations. What was done with the previous APs was to mount a unistrut beam to an I beam in the building. There is 2 AIR-ANT-1728's and 2 AIR-ANT-5160V-R antennas mounted straight out on the unistrut. Then they put a T bracket on the unistrut and mounted a second bar 90 degrees from the main bar and connected the third 1728 and 5160 antennas on the second mounting bracket. So we have 4 antennas in a row, and two off to the side 90 degrees from the other 4 antennas.
My question, is this OK to have them this way, or would it be better to have all 6 antennas in a straight line when I fabricate my new AP brackets?
Here is a picture of what I am talking about. This would be looking at it from above.
Current New Proposal
__________o__o__o__o_ _________o__o__o__o__o__o
| AP AP
|
|o
|
|o
Any replacement bracket or some other way to easily mount the 942l in a window? i have a long window next to my front door i want to just stick this someone about shoulder high in that window looking right to the door so will see anyone who comes.
View 5 Replies View RelatedI am looking for a wall mount bracket reference, for these 2 models of antennas :
- AIR-ANT5160V-R
- AIR-ANT2506
Something like that :I was not able to find any reference in cisco product list.
I want to replace existing 1242s with 1262s. Which are currently in a Heated Nema Enclosures with 12dBi Mast Mount AIR-ANT24120. The 5.0 Ghz Radio is off. So the question is can I use the same Antennas AIR-ANT24120 for the new 1262? I’m assuming yes as long I use connectors A & C are tx/rx; on the center would we leave open or put a rubber duck on it?
View 3 Replies View RelatedI have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC. Some of these APs are using AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi) and Mobile Mark OD9-240 (2-GHz omnidirectional 9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
View 4 Replies View RelatedI mounted the router to the wall with the 2 screw holes and screws. Now I want to take it off from the wall, but it is stuck
View 4 Replies View Relatedwhat's the best antenna arrangement for wall mounting the WAP4410N?I see pictures of the antennas for desk mount but nothing for a wall or ceiling mount.Should I just fiddle with them and see what works best?
View 3 Replies View RelatedI have a question if your Cisco 800 series wireless in a rack mount installation in racks to place the signal strength materials very well ?
View 0 Replies View RelatedHow to get the 1231g to work with WPA2-PSK (AES). My laptops cannot authenticate using this config but connect fine to the 1242AG. Below are some of the specifics:
1231G
Radio Type: AIR-MP31G
IOS Ver: 12.3(8) JED
Multiple SSID
Encryption: AES
Key Management: Mandatory WPA
*Laptops can connect to SSID with WEP
I bought 3 of the Aironet 1231g access points and cannot get any clients to connect to them. I have tried everything from an Iphone, Droid2, Win 7 and XP laptops with built in wireless G cards. All say that they cannot connect to the wireless network. I have two setup currently, one on Vlan 1 that I have configured the way I want with WPA2 enterprise. The other one is just one I setup while playing around.
View 4 Replies View RelatedI configured one vlan and trying to authenticate it through radius server.My objective is when a internal users want to connect through this SSID they just put username and password and authenticate through Radius server. Another vlan is getting authenticated through mac address that i need to manually put in AP.
View 2 Replies View RelatedI'm thinking to buy a E2500 router for my house. Is it possible to wall mount it?
View 7 Replies View RelatedI'm trying to mount a network share from a Linksys NAS200 to Fedora 16.
The program I am trying to run won't accept network addresses to save to. I ran it without specifying the IP address of the server and it comes up with some random IP. I specified an IP and it can't find the device.
Here are the errors:
[root@HOME ~]# mount -t cifs -v //NAS_SERVER/public/ /mnt/ -o username=user,password=pass
mount.cifs kernel mount options:
[Code].....
Is there a replacement rackmount kit available for a Smart Switch SF200-48?
View 1 Replies View RelatedCan the EA4500 be wall mounted? I don't see any provisions on the underside EA4500 to support securing to a wall.
View 9 Replies View RelatedIs there a wall mount bracket for the E2500 or is there a way of attaching this to a wall.
View 1 Replies View RelatedI have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI am having an issue with my Cisco 1231G access points. When I make a password change on either SSID I am broadcasting, any device I try to reconnect to the network on will not prompt for the new password. It will just say unable to connect to whatever network. The 1231G AP is using the 12.8 (8) JEA IOS version. I have had Apple, Android, and windows laptops all not ask to enter a new password. It's like the device is not recognizing that it has changed. Is this an IOS bug or a setting I have to check. I can attach a configuration if necessary.
View 6 Replies View RelatedI have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedMy company AP 1231G is not passing the DHCP address to the client from the DHCP server, my config listed below basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
!
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
!
[Code].....
Is there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedI think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies View RelatedI have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies View RelatedI have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedHere at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
Okay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.
View 14 Replies View Related