what's the best antenna arrangement for wall mounting the WAP4410N?I see pictures of the antennas for desk mount but nothing for a wall or ceiling mount.Should I just fiddle with them and see what works best?
View 3 RepliesI am looking for a wall mount bracket reference, for these 2 models of antennas :
- AIR-ANT5160V-R
- AIR-ANT2506
Something like that :I was not able to find any reference in cisco product list.
I'm thinking to buy a E2500 router for my house. Is it possible to wall mount it?
View 7 Replies View RelatedCan the EA4500 be wall mounted? I don't see any provisions on the underside EA4500 to support securing to a wall.
View 9 Replies View RelatedIs there a wall mount bracket for the E2500 or is there a way of attaching this to a wall.
View 1 Replies View RelatedI mounted the router to the wall with the 2 screw holes and screws. Now I want to take it off from the wall, but it is stuck
View 4 Replies View RelatedI am still new to wireless. I have been studing for my CCNA Wireless for about 6 months now so I still have a lot of questions.
Right now I have to deploy some new APs. We are using 3502e APs. I have a qustion on how to mount antennas for these access points. I have to make a mounting bracket the new installations. What was done with the previous APs was to mount a unistrut beam to an I beam in the building. There is 2 AIR-ANT-1728's and 2 AIR-ANT-5160V-R antennas mounted straight out on the unistrut. Then they put a T bracket on the unistrut and mounted a second bar 90 degrees from the main bar and connected the third 1728 and 5160 antennas on the second mounting bracket. So we have 4 antennas in a row, and two off to the side 90 degrees from the other 4 antennas.
My question, is this OK to have them this way, or would it be better to have all 6 antennas in a straight line when I fabricate my new AP brackets?
Here is a picture of what I am talking about. This would be looking at it from above.
Current New Proposal
__________o__o__o__o_ _________o__o__o__o__o__o
| AP AP
|
|o
|
|o
I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.
View 0 Replies View RelatedI have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
I want to replace existing 1242s with 1262s. Which are currently in a Heated Nema Enclosures with 12dBi Mast Mount AIR-ANT24120. The 5.0 Ghz Radio is off. So the question is can I use the same Antennas AIR-ANT24120 for the new 1262? I’m assuming yes as long I use connectors A & C are tx/rx; on the center would we leave open or put a rubber duck on it?
View 3 Replies View RelatedI have a question if your Cisco 800 series wireless in a rack mount installation in racks to place the signal strength materials very well ?
View 0 Replies View RelatedI was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies View RelatedHow to mount the E4200 on a wall. Any smart ways to do it?
View 9 Replies View RelatedI just bought this router used and in working condition. I dl'd the install file from here and followed all the directions. When it gets to the plug router into wall portion, it just sits there and eventually says its hooked up wrong. However the wifi is already working (checked by logging into my kindle fire) as well as my second port which is hooked to my ps3. However my 1st port which is connected to the pc does nothing. I have swapped the cables with no luck. So I cant figure out why there is no communication between the router and my pc.
View 9 Replies View RelatedMy dorms have wifi in the common room, and ethernet wall ports in the rooms since wifi doesnt reach that far. They both have the same network name (e.g. the wifi network is named 'apple', and when i connect through ethernet in my room the name is also 'apple') I need to have wifi in my room. So, if i get a router and connect it to the ethernet port in my room's wall, would that work? Is that all you have to do or is there some other stuff i should know about?also can i put a password on it? And also, will it carry the network traffic of the common room?(if two people are using the common room's wifi, will the wifi speed in my room be affected nd whatnot) i have a linksys router lying around at home (the blue one with the double antennas, everyones seen them, and the one in the common room is the same...wireless g)
View 7 Replies View Relatedanybody with 2 x rack mount kits for a SRW208P that they don't want? I need to rack mount these devices but my predecessor very wisely decided to throw them out and Cisco does not sell the racks as a separate SKU.
View 1 Replies View RelatedI need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 Replies View RelatedAny replacement bracket or some other way to easily mount the 942l in a window? i have a long window next to my front door i want to just stick this someone about shoulder high in that window looking right to the door so will see anyone who comes.
View 5 Replies View RelatedI'm trying to mount a network share from a Linksys NAS200 to Fedora 16.
The program I am trying to run won't accept network addresses to save to. I ran it without specifying the IP address of the server and it comes up with some random IP. I specified an IP and it can't find the device.
Here are the errors:
[root@HOME ~]# mount -t cifs -v //NAS_SERVER/public/ /mnt/ -o username=user,password=pass
mount.cifs kernel mount options:
[Code].....
Is there a replacement rackmount kit available for a Smart Switch SF200-48?
View 1 Replies View RelatedI have CAT5 cables run throughout my house to a few different jacks. They plug into my modem downstairs. I want to hook up my desktop internet through one of the wall jacks upstairs. The wall jack has CAT5 cable run to it but only accepts telephone wire sized jacks. How do I connect to the internet with this setup?
View 14 Replies View RelatedI'm wiring the house with CAT6 solid cable. Can I use CAT5e wall sockets?
Are there actually any differences between CAT5e rated sockets and CAT6 rated sockets, aside from the latter being vastly overpriced?
I haven't worked with Cisco devices before (yepp, another one of those) but I am getting there. I have replaced my silly Draytek router now with a Cisco877 and it works perfectly fine. But the whole networking side of things such as NAT / ROUTE / ACLs is a BIT black magic.
Basically my problem is that I cannot get proper traffic through the tunnel
From any station behind the Cisco (Site2) I can ping the local IP of the Sonic, but none of the other stations. From behind the Sonic I can ping any station behind the Cisco but unable to connect on any port (RDP for example)
Bear in mind that a lot of settings are from forums, google and the sorts because as I mentioned, before I got this one I have limited experience with Cisco .. Everything configured is working fine, the internet connection, the incoming pptp VPN to the Cisco etc., just not the IPSec VPN.
SO I am not a computer wiz... but I have this outlet in my upstairs wall which has a phone and Cat5e Jack. I would like to set up my wireless router up there but where does the modem go? there is no jack for the cable.
View 1 Replies View RelatedI have done similar with cat5e in the past, but only operating at 100mb/s. The gigabit stuff I have done so far has had the power in a separate stud cavity.My structured wiring project will be installed in one stud cavity in the soon to be new home office. Not exactly using a structured wiring cabinet, but rather using a 7u wall mount relay rack bracket. The cabling will be entering using 2 separate header penetrations. One existing just inside on the right side of the stud cavity carries 110V 12/2 romex to a stud attached box / recepticle. The other side gets the new penetration, a minimum of 12" away. That's the one that the ethernet cable will pass through. The cable runs will run through the wall and through a brush plate, and then to the patch panel.
The Cat6 cable is UTP, and is marked for in wall use. This is the stuff with the spline if that matters.The romex, by code MUST be attached to the stud, and it is, the cat6 on the other hand is allowed to be loose in the wall. I do not plan on having enough slack in the wall for the cat6 to ever get closer than 8" from the romex, and no closer than 10" from the electrical box.Is that separation sufficient to avoid inductive noise on the ethernet cables? Like I said, I have done similar with Cat5e and no problems ever, but only attached to 10/100 networks. I can change stud cavities, but would rather stick with the one so that my ethernet, and power both can enter the rack cleanly.
the internet is so poor I usually lose the signal, since it has to go through walls and a bunch of trees. My question is can I use the phone jacks in the wall to set up a second router or something to increase it. Or what is the best way to increase the power and strength. What do I need and how do I do it. My fathers router is under verizon vios. I plan on getting and xbox 360 with live capability and need good internet for that
View 2 Replies View RelatedI have a side gig that I do some work for and they've had a Sonicwall TZ200 device in their branch office and also in their data center that has a site to site VPN connection between the two devices. About a month ago the bandwidth throughput got severly decreased. They went from getting about 28Mbps/27Mbps to now ~3Mbps/12Mbps.
I've spent days troubleshooting with Sonicwall which could be a whole dedicated thread on it's own but I digress. I even had the ISP come out and test the line and when they hooked up their own laptop it got the speeds it should be getting. I've rebuilt the config on the sonicwall from scratch which was a major pain in the ass because I'm not a firewall guy by any means. After firmware updates and pulling my hair out I've decided to dump the tz200, to what I don't know. I need two devices, one for the data center and one for the branch office. I'm pretty sure something in the config is causing this and after being escalated to the highest level at sonicwall and them sending me a replacement unit which I rebuilt the config on and also tried to import the old settings with no luck. I very well could have done something or made a change to cause this but I'm at a loss and willing to try another product.
I get spammed from Barracuda all the time, do they have quality devices? Something with a web interface would be great since I'm not a firewall guru by any means and had set up a bunch of address objects with NATs and all that.
I'm wiring up the house with CAT6 (I've never done this before). Someone told me to use 'T568B' termination. Every configuration I see on net looks different, and I'm getting confused.
The jacks have double colour coding for each wire as pictured here:I take it 'A' is for T568A, and 'B' is for T568B?So this is how I should arrange the wires for T568B:
Have a Sonicwall with multiple VLANS on LAN interface going to the SG-300 in Layer 3 mode.Trunk Port has VLAN 1 untagged and PVID and other VLANS (20,30,40) tagged.Setting a port to Access for particular VLAN (40) does not pull DHCP from Sonicwall.Sonicwall support says DHCP request is coming from VLAN1 and something wrong in switch setup.Setting 2 ports to VLAN 40 allows communication between the two.Also, replacing SG300 with a Netgear L2 works.Seems like an issue with the trunk, no?
View 2 Replies View RelatedWE've been using the Asoka pluglink adapters we received from at&t and they worked very well to where we can move them anywhere in the house. Now they've just stopped working all together. We didn't change anything to where they stopped working. But the weirdest part: they just started working again yesterday and now are not. I did not influence any of these changes and I'm not sure where the problem is. I've tried swapping out the adapters cause we have three and we only use two at a time. Our current setup is a linksys wrt54g with ddwrt which is what we plug one of the adapters to and the other is in my room cause we are out of range for wireless. When testing the network it says we join an unidentified network but have no internet access.
View 4 Replies View RelatedIs there a Cisco wall-plate model? Something similar to HP E-MSM317 and Ruckus 7025? I had look on the web but couldn't find anything.
View 3 Replies View RelatedI need to update from older Cisco 350 Aironet 802.11a/b Wireless CardBus Adapters to Cisco cb21ag Aironet 802.11a/b/g Wireless CardBus Adapters in rugged tablet pc's. I need these without the antenna cap present to utilize the tablets antenna sytem. They are pictured on the Cisco website but Cisco partners I've contacted have been unable to assist me in purchasing them.
View 1 Replies View RelatedI have a AIR-LAP1242G-A-K9. I have several question:
1. Does the antenna is a MUST for it to work.
2. If I have a 1 unit of AIR-ANT2422DG-R (antenna) , does the wireless access still work? Do I need 2 antenna
3. If I have a 1 unit of AIR-ANT2422DG-R, does 802.11 b supported.