I bought 3 of the Aironet 1231g access points and cannot get any clients to connect to them. I have tried everything from an Iphone, Droid2, Win 7 and XP laptops with built in wireless G cards. All say that they cannot connect to the wireless network. I have two setup currently, one on Vlan 1 that I have configured the way I want with WPA2 enterprise. The other one is just one I setup while playing around.
View 4 RepliesMy company AP 1231G is not passing the DHCP address to the client from the DHCP server, my config listed below basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
!
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
!
[Code].....
Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
Where I live there is no DLS or cable to probide me with Interent access so I use my Verizon 3G/4G smart phone (Android) as a hotspot. Right now I am using an old Vista PC and ICS (Internet Connection Sharing) to provide Interent connectivity to my home network and Cisco lab. This works fine but I must have my smart phone near the PC for it to work. When I go to other rooms, I end up missing calls and texts since I have t oleave the phone if it is providing Inerent access at that time. If I can get the Airnet's to connect to the hot spot AND provide Internet access, that will provide me additional mobility. This would also be good for small businesses as a backup Internet Connection.
Is there any way that I could elimanate the Vista PC and have my Aironet 1231G Wireless router(s) automatically connect to my phone's 3G hotspot to provide Internet access to my lan?
I have 2 Airnoet 1231G's running the c1200-k9w7-mx.123-7.ja IOS and a C3550XL layer 3 switch.
I have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC. Some of these APs are using AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi) and Mobile Mark OD9-240 (2-GHz omnidirectional 9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
View 4 Replies View RelatedHow to get the 1231g to work with WPA2-PSK (AES). My laptops cannot authenticate using this config but connect fine to the 1242AG. Below are some of the specifics:
1231G
Radio Type: AIR-MP31G
IOS Ver: 12.3(8) JED
Multiple SSID
Encryption: AES
Key Management: Mandatory WPA
*Laptops can connect to SSID with WEP
I configured one vlan and trying to authenticate it through radius server.My objective is when a internal users want to connect through this SSID they just put username and password and authenticate through Radius server. Another vlan is getting authenticated through mac address that i need to manually put in AP.
View 2 Replies View RelatedI have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI am having an issue with my Cisco 1231G access points. When I make a password change on either SSID I am broadcasting, any device I try to reconnect to the network on will not prompt for the new password. It will just say unable to connect to whatever network. The 1231G AP is using the 12.8 (8) JEA IOS version. I have had Apple, Android, and windows laptops all not ask to enter a new password. It's like the device is not recognizing that it has changed. Is this an IOS bug or a setting I have to check. I can attach a configuration if necessary.
View 6 Replies View RelatedI need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 Replies View RelatedI have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedIs there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedWe have 12 - AP-1231G access points in our warehouse with 2 SSID's, both on different VLAN's. We would like to set one of the VLAN/SSID 's to use DHCP from a windows DHCP server.Is this possible to do with option 43 or is that only for lightweight AP's ? Sho ver: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8).
View 2 Replies View RelatedI think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies View RelatedI have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies View RelatedI have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedOnce a client connects to my VPN (VPN Client 5) they can not see anything other than the outside interface. If I ping anything on the LAN for example I get a reply from the outside interface. I can not see any WAN either (even by IP) My LAN clients can see the clients within the VPN Pool. I would like all traffic to flow through the VPN. I have tried split tunneling to verify if the internet would work and local lan would stay connected. It does work but I was still unable to access anything on the remote netwok. I am not sure if I am missing a nat command or something simple.
The current setup is as follows. 881 Router with windows 2008 radius authentication. The client is authenticating and reciving an IP address from the local ip pool. Please see below for the running config.
crypto ipsec transform-set myset esp-3des esp-sha-hmac
!
crypto dynamic-map dynmap 10
set transform-set myset
!
!
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedI am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
I just purchased a WAP 321 and followed the setup wizard. Its powered by a poe switch. The issue I have is no clients can connect to it. I updated the firmware. I reset to factory and tried setting it up manually till no one can connect. I dont understand what im doing wrong here. Unless its a bad unit. I will have about 10 to 15 clients connecting to it. Its the only ap in the building.
View 12 Replies View Related I configured the VPN on the ASA, I can not get a client to connect to the ASA
: Saved:ASA Version 7.2(2) !hostname domain-name enable passwordnamesddns update methodddns both!!interface Vlan1nameif insidesecurity-level 100ddns update hostname ddns update dhcp client update dnsip address 192.168.1.1
[Code].....
Basically, yesterday while hanging some 3602's going to a different controller, I started getting task reports of wireless phones not working. However, due to the area of complaint I mistakenly assumed it was due to me causing havoc in the area with AP replacements. Then the issues started to spread with Carts and Cow's and other various devices not able to connect until it started affecting me. I was not able to connect to any SSID at all, kind of nerve racking when you talking ICU/NICU area's in a hospital. Once I got to a wired device, my first thought was to move the AP's to a different controller to at least try and get things back up and then work on the controller to see what was going on. However, in trying to get the AP's to move, most of them wouldn't. In hind sight, I wish I had just shut off the etherchannel port on the 6500 that this wlc is on and force the AP's to move that way, but with people standing over me I ended up just rebooting the controller. Of course, once it came back up the AP's reattached to it but everything was working fine. I went ahead and moved the AP's off of it to another controller for now but am searching for answers. About to start digging into bug reports, but am concerned with this line of code causing the issue and worried about moving to 7.2.110.
View 4 Replies View RelatedPurchased an 887 my my home office. ADSL ATM0 and Dialer get an address from my ISP, have tried to configure NAT but none of my clients can browse the internet. I can't ping outside the network but I can ping clients internally as my clients are connected via a switch, which is plugged in before the 887. I can get access to the router via the Command Line and CP Express and Config Pro seems to work.
Building configuration...
Current configuration : 8900 bytes
!
! Last configuration change at 12:47:16 NewYork Wed Dec 14 2011 by elrooko
[Code].....
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI want to know why all my wifi client connect only in G protocol, even if the wireless card supports N, even if all the AP in one of my buildings is AP3500. In the WCS config for my two WISM controller the 802.11a network status is disable, the 802.11n network status is enable and the 802.11b/g Network status is enable and 802.11g support is enable. even in that part of config the 802.11n is enable.
In the High throughput 802.11n section all the rates is check to be supported.
What config I'm missing to get my 802.11N client to get connected with this protocol and not on G protocol.
I have an ASA 5505 that has had a working configuration with several AnyConnect clients using dual authentication for weeks now. My normal process for adding new users has been to configure the user in both authentication databases and the onboard certificate authority, have the user connect to the outside IP of our firewall with IE, download the P12 cert after entering their OTP and then connecting once the cert's imported to download AnyConnect.
I had to add a new user a couple days ago and curiously IE (8) on their computer could not connect to the outside interface of our firewall, as if the laptop had no internet connectivity. I could telnet to port 443 from a command-line, and could even hit it with Firefox (which I ended up doing to download the P12 cert...). I can hit other SSL-enabled and standard websites from IE as well as Firefox. In addition, because AnyConnect seems to rely on the same mechanism to connect as IE does, AnyConnect can't connect either.
I then tested using a previously working laptop fully configured with AnyConnect and a certificate and now it can't connect. There are other previously working laptops that still work, which only makes the issue more clouded.
In watching the logs on the firewall, when one of these non-working computers attempts to connect they hit the firewall, a connection is opened and the SSL handshake is started, but it's never finished and the connection is torn down. Working computers complete the handshake as expected and a tunnel is opened.
I've checked IE forums for this issue and none of the fixes found therein seem to apply or work. Since this issue seems to only affect IE and AnyConnect's ability to connect to my firewall I have to assume the issue is there.
What's wrong with this config ? Clients can see the wireless ssid's but cant connect.
View 1 Replies View RelatedI have a computer (client) and I have connected to gateway and internet but I'm not connected to other clients.
View 3 Replies View RelatedI have a 4402 which is connected to a 4506 Switch int Gig 3/1 via a trunk port. The Managment and AP-manger interfaces are on vlan 6 [code] I have a 1142N AP also connected to the switch and it pulls a DHCP IP Address and configs etc and registers to the WLC. It too is on Vlan 6 and it is connected to the 4506 on int gig 4/33 which is an access port. [code] I am doing local authentication, so i have added users to the WLC.. My problem is that the first client that connected was able to get an IP address and connect to anything internal and external.I then connected another client on another laptop and that client could connect but not get an IP address, it just self assigned.When i look at the clients i can see the MAC address of both Clients on the WLC, but doing a show mac address-table dynamic i only see the MAC of the client that works properly. The client that doesnt get an IP has no entry in the 4506 switch.I am stumped, from what I understand, is that the 2nd clients traffic is being trunked to the WLC , hence it has the MAC address. But I dont know why its not getting a DHCP assigned IP address.
View 37 Replies View RelatedI am currently having some problems on our 5520 ASAs. The problem is the IPSec VPN clients not being able to connect. We have had an issue twice this week where this happened. Earlier in the week we had folks not able to sign in, but some folks who were connected already stayed connected. The ASAs had been up for 200+ days and no changes have been made to it recently. At that point I had to reload the ASAs so users could start signing back in to it. Today we had a similar issue, but I didn’t have to reload the ASAs. The issue‘resolved’ itself. The VPN clients are getting Error code: 433 and the ASAs are getting Reason: Peer Address Changed when this occurs.
ASA5520, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz version 8.3.2.