How to get the 1231g to work with WPA2-PSK (AES). My laptops cannot authenticate using this config but connect fine to the 1242AG. Below are some of the specifics:
1231G
Radio Type: AIR-MP31G
IOS Ver: 12.3(8) JED
Multiple SSID
Encryption: AES
Key Management: Mandatory WPA
*Laptops can connect to SSID with WEP
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedI have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC. Some of these APs are using AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi) and Mobile Mark OD9-240 (2-GHz omnidirectional 9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
View 4 Replies View RelatedI configured one vlan and trying to authenticate it through radius server.My objective is when a internal users want to connect through this SSID they just put username and password and authenticate through Radius server. Another vlan is getting authenticated through mac address that i need to manually put in AP.
View 2 Replies View RelatedI have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedMy company AP 1231G is not passing the DHCP address to the client from the DHCP server, my config listed below basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
!
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
!
[Code].....
Is there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedWhere I live there is no DLS or cable to probide me with Interent access so I use my Verizon 3G/4G smart phone (Android) as a hotspot. Right now I am using an old Vista PC and ICS (Internet Connection Sharing) to provide Interent connectivity to my home network and Cisco lab. This works fine but I must have my smart phone near the PC for it to work. When I go to other rooms, I end up missing calls and texts since I have t oleave the phone if it is providing Inerent access at that time. If I can get the Airnet's to connect to the hot spot AND provide Internet access, that will provide me additional mobility. This would also be good for small businesses as a backup Internet Connection.
Is there any way that I could elimanate the Vista PC and have my Aironet 1231G Wireless router(s) automatically connect to my phone's 3G hotspot to provide Internet access to my lan?
I have 2 Airnoet 1231G's running the c1200-k9w7-mx.123-7.ja IOS and a C3550XL layer 3 switch.
We have 12 - AP-1231G access points in our warehouse with 2 SSID's, both on different VLAN's. We would like to set one of the VLAN/SSID 's to use DHCP from a windows DHCP server.Is this possible to do with option 43 or is that only for lightweight AP's ? Sho ver: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8).
View 2 Replies View RelatedI have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies View RelatedI have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
I bought 3 of the Aironet 1231g access points and cannot get any clients to connect to them. I have tried everything from an Iphone, Droid2, Win 7 and XP laptops with built in wireless G cards. All say that they cannot connect to the wireless network. I have two setup currently, one on Vlan 1 that I have configured the way I want with WPA2 enterprise. The other one is just one I setup while playing around.
View 4 Replies View RelatedI have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI am having an issue with my Cisco 1231G access points. When I make a password change on either SSID I am broadcasting, any device I try to reconnect to the network on will not prompt for the new password. It will just say unable to connect to whatever network. The 1231G AP is using the 12.8 (8) JEA IOS version. I have had Apple, Android, and windows laptops all not ask to enter a new password. It's like the device is not recognizing that it has changed. Is this an IOS bug or a setting I have to check. I can attach a configuration if necessary.
View 6 Replies View RelatedI need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 Replies View RelatedI think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies View RelatedI have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedI am in the process of moving our office and part of the task involves relocating our existing wireless access points. They are all 1242AG's running the c1240-k9w7-mx.124-10b.JDA3 IOS. I would like to change the security on the access points to WPA 2 but that selection is not available. I think upgrading the IOS will solve this problem but I am not sure. So I guess I have two questions:
1) Does this Cisco model support WPA 2 ?
2) If so what IOS do I need to load to make WPA 2 available?
I purchased quite a few of these APs as they listed the ability to function in WPA2-PSK mode, but on initial configuration I see that this may only apply to standard AP mode? Is there any way to configure WPA2-PSK on an AP541 to AP541 bridge? Unfortunately, this is a must have for our client. If not, what would allow for this with an external antenna port?
View 4 Replies View RelatedI am looking for an example configuration of a Cisco 1310 running 123-7.JA2 Z Ios, for Wpa2 using an external Cisco acs radius server.
View 3 Replies View RelatedI have a problem with Cisco WLC 2106 (SW: 7.0.98.0) and LAP1262. The client roams to new AP, associates with the new AP and authentication (WPA2 with EAP-TLS) runs fine until WPA2 key exchange.
The first WPA2-Key-paket from AP (1 / 4) is sent twice. On a closer look at those packets with Wire shark, i've found out the first is encapsulated into a 11n-frame (A-MSDU). The resent frame isn't. This figure shows the first WPA-Key-packet:
The next figure shows the 2nd key-packet, without 11n-encapsulation: The problem, that occurs a very long roaming-time with about 5 seconds. As you can see on second figure, the second wpa-key is sent 5 seconds after the first.
Some details:
Client: Tablet PC with Intel 6230 agn
Controller: Cisco WLC 2106
AP: LAP 1262
Controller SW: 7.0.98.0
Encryption: WPA2-AES
Authentication: EAP-TLS
This problem occurs just on 5-GHz interface with 40 MHz channel bandwidth.
Is there anyway to have my wireless network secure on an WPA2? I am sharing with my landlords network. Everytime I try to create a 14 digit password it disables my connection. Does my landlord have to create a password or can I just do it myself?
View 1 Replies View RelatedCould you find wpa2 of the airlink 101 super g wireless router for me?
View 1 Replies View Relatedwhat is my wireless internet wpa2 password.
View 1 Replies View RelatedI am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes
!
version 12.4
no service pad
[Code].....
we have a cisco WLC 5508 on which few SSIDs are configured, and two kinds of APs: AIR-LAP1142N-E-K9 and converted AIR-AP1141N-E-K9.
When in WLAN settings we leave WPA2 policy and AES encryption, iPads2 can connect without any problems to AIR-LAP1142N-E-K9, but there is no connection to converted AIR-AP1141N-E-K9. MacBooks, iPhones are connecting without questions.
When we set WPA2+TKIP everything is cool, but other Apple devices can't rich 802.11n speeds((
With only WPA2+AES or both WPA2+AES+TKIP enabled on a WLAN the WLC gets such messages :
Decrypt errors occurred for client xx:xx:xx:xx:xx:xx using WPA2 key on 802.11b/g interface of AP xx:xx:xx:xx:xx:xx
But I know that it can happen when you offer funny encryption combinations that client doesn't like (wpa1+aes, wpa2+tkip). But the advise to try to only enable wpa2/aes for some reason doesn't work.
Can a WAP4410N be used as a repeater on an existing WPA2 + EAP-TLS WLAN? The existing WLAN is on a Cisco 871W router; we hope to use a WAP4410N as a repeater to extend it.
I've not had much luck so far with the "repeater" and "WDS repeater" AP modes on the 4410. I'm either configuring it wrong, or perhaps the 871W needs a config tweak? Or perhaps the 871's wireless can't be repeated like this?
We are using an Aironet 1240AG series wireless AP here to connect handheld scanners. They work fine on WPA. However, when we switch to WPA2, they often lose connection. We have tested on 802.11g and a bands, with various encryption types (TKIP, AES, TKIP/AES). Also, how can I update the outdated firmware without signing up for a service contract?
View 3 Replies View RelatedI have an aironet 1141 with multiple v lans configured, all with wpa2 but I need to put mac filter on only one v lan, so I follow this manual: [URL}. Basically is mac a ACL and applied to sub interface. So, I can associate to the AP, but no one can transmit or receive . If i remove the ACL all works fine.
My config:
access-list 700 permit <maclist> 0000.0000.0000
access-list 700 deny 0000.0000.0000 ffff.ffff.ffff
interface Dot11Radio0.130
[code]....
This is a 5-year-oldish Gateway MX-6124 laptop running under Win XP 2002, SP3. I'm using SureWest DSL, with an ISP-supplied ComTrend NexusLink 5631 Modem/Router. The router is set up as a Secure Network, using WPA encryption. The laptop wireless operation light toggles off/on correctly using Fn-F2 control keys.I can connect to an open or non-secured wireless router, & have verified that at my church, at the Public Library, and at Starbucks. However, I cannot successfully connect to a passworded secured wireless source. I tried to use a secured network connection at my church yesterday, and could not connect. It "tries & tries" and eventually gives up and displays a cannot-connect type of message.
The laptop has worked correctly for several years on my home wireless network. It only stopped working about 3 or 4 weeks ago. I cannot recall changing anything in setup; I probably did it accidentally.I've spent about 2 hours in a couple of sessions with SureWest tech support. They diagnosed router setup using direct connect to the router, plus they talked me through several attempts at configuring the wireless config setup on the laptop. Everything I reported to them on the config settings appeared to be just fine. They also deduced that the wireless config on the desktop & router was correct.SureWest techs finally concluded that something was wrong with my laptop software config or the hardware, disabling it from making a encrypted connection. That sounds right to me, now having witnessed the secured connection failure described above, at my church wireless site.
I've looked at all the refs & things I can think of, plus followed step-by-step directions a couple of times with the SureWest techs. They rightfully pointed out that they could not make a tech support repair call on what did not appear to be a SureWest-related problem.I can easily make screenshots of any config screens needed on the laptop & upload to this forum.
Could you give me the WPA2 of the Airlink 101 wireless router?
View 2 Replies View Related