I configured one vlan and trying to authenticate it through radius server.My objective is when a internal users want to connect through this SSID they just put username and password and authenticate through Radius server. Another vlan is getting authenticated through mac address that i need to manually put in AP.
View 2 RepliesI have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC. Some of these APs are using AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi) and Mobile Mark OD9-240 (2-GHz omnidirectional 9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
View 4 Replies View RelatedHow to get the 1231g to work with WPA2-PSK (AES). My laptops cannot authenticate using this config but connect fine to the 1242AG. Below are some of the specifics:
1231G
Radio Type: AIR-MP31G
IOS Ver: 12.3(8) JED
Multiple SSID
Encryption: AES
Key Management: Mandatory WPA
*Laptops can connect to SSID with WEP
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedMy company AP 1231G is not passing the DHCP address to the client from the DHCP server, my config listed below basicly the AP is on its own VLAN 10.1.123.1 and the DHCP server is 10.1.10.2 -- trying to use iphelper to pass DHCP to clients and the AP is on static IP 10.1.123.2--
!
! Last configuration change at 13:15:56 +0800 Fri May 25 2012 by root
! NVRAM config last updated at 13:15:56 +0800 Fri May 25 2012 by root
!
[Code].....
Is there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedWhere I live there is no DLS or cable to probide me with Interent access so I use my Verizon 3G/4G smart phone (Android) as a hotspot. Right now I am using an old Vista PC and ICS (Internet Connection Sharing) to provide Interent connectivity to my home network and Cisco lab. This works fine but I must have my smart phone near the PC for it to work. When I go to other rooms, I end up missing calls and texts since I have t oleave the phone if it is providing Inerent access at that time. If I can get the Airnet's to connect to the hot spot AND provide Internet access, that will provide me additional mobility. This would also be good for small businesses as a backup Internet Connection.
Is there any way that I could elimanate the Vista PC and have my Aironet 1231G Wireless router(s) automatically connect to my phone's 3G hotspot to provide Internet access to my lan?
I have 2 Airnoet 1231G's running the c1200-k9w7-mx.123-7.ja IOS and a C3550XL layer 3 switch.
We have 12 - AP-1231G access points in our warehouse with 2 SSID's, both on different VLAN's. We would like to set one of the VLAN/SSID 's to use DHCP from a windows DHCP server.Is this possible to do with option 43 or is that only for lightweight AP's ? Sho ver: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8).
View 2 Replies View RelatedI have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies View RelatedI have two Aironet 1231Gs, that are both running the same version of fimware: Version 12.3(8)JEE
From the gui, I try and change the channel on the main radio interface--It works from one, and I get just a blank page on the other. When I try and change it via the cli, I use the "channel" command in conf int mode, and it works one the one, but the other one, the "channel" command doesnt exist.
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
I bought 3 of the Aironet 1231g access points and cannot get any clients to connect to them. I have tried everything from an Iphone, Droid2, Win 7 and XP laptops with built in wireless G cards. All say that they cannot connect to the wireless network. I have two setup currently, one on Vlan 1 that I have configured the way I want with WPA2 enterprise. The other one is just one I setup while playing around.
View 4 Replies View RelatedI have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI am having an issue with my Cisco 1231G access points. When I make a password change on either SSID I am broadcasting, any device I try to reconnect to the network on will not prompt for the new password. It will just say unable to connect to whatever network. The 1231G AP is using the 12.8 (8) JEA IOS version. I have had Apple, Android, and windows laptops all not ask to enter a new password. It's like the device is not recognizing that it has changed. Is this an IOS bug or a setting I have to check. I can attach a configuration if necessary.
View 6 Replies View RelatedI need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 Replies View RelatedI think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP.
View 3 Replies View RelatedI am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedI have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedSoon to be working on a design for a Wireless installation across one of our buildings. The wireless survery has been completed, and we'll be installing 175 APs, across the 3 floors of the building.
With regards to the back-end WLC setup, I have a few queries around the WLC configuration. We're looking at implementing the 4400 series of devices, and due to us having nearly 200 APs, we'll need at least 2 x 4404 or 4 x 4402 - I'm assuming its simpler to have fewer devices to make management simpler.Also, looking at the Cisco reference material, they recommend that a 4404 can support up to 100 APs, with regards configuring the ports on the box, would I need to configure LAG across the WLC
ports in order for it to accommodate all of the Access Points. If we were to go with a scenario of using 2 x 4404 devices, would we be in a position whereby if we lost a Controller, we'd lose
all of the Access Points associated with that Controller? In order for us to have full resiliency, we'd need an additional 4404 controller for the APs to failover on too? From a licensing perspective, we'll be purchasing a licence to cover 200 APs.
I have a wireless install using several standalone 1142 Access Points. Yes, I know it would be better to use a WLC, but there isn't one and no funds to install one, so I have to work with what's there...
I'd like to configure the 1142's for wireless N connectivity. Yes, I know I need to ensure WPA/PSK is the security used as WPA/AES, the default option in the CLI won't be happy with wireless N.Currently I am running them in B/G only and they work just fine with WPA/AES. No issues are reported by the users, but of course I'd like to get them running N for the increased throughput so I need to kniow the CLI steps required.
My client would like to have a wireless deployment between several differented offices in the city. There is connectivity between the different sites...but my main issue is, is this option really feasible. I was thinking of a centralized WLC like the 2504 coz of price + 36 APs, 2 at each site. The main worry is the network setup considering the fact that the APs have to communicate with the WLC so unpredictable network issues i believe will have a very huge impact.
View 4 Replies View RelatedI have Cisco WiSM running on 7.0.116.0 and 1522 Outdoor AP. I a trying to configure Mesh and I followed the Cisco deployment guide.I had added the MAC address of my AP in the Mac-filter list Configured the Root AP and Mesh AP.Configured the Mesh Parameter.Currently my issue is after removing the client from Ethernet its no more seen in the controller. There is also no information in the neighbour output.
View 2 Replies View RelatedRouter: Cisco WRVS4400N secured with WPA2WAP: Cisco WAP4410N . Router was working well but signal too weak in distant rooms. So, purchased a WAP4410N but am unsure about AP configuration. From reading the docs, I understand these to be the relevant choices:
1) Access Point -- Wired connection through built-in Ethernet port. (Not Desired)
2) Wireless WDS Repeater
3) Wireless Client / Repeater (What is difference from WDS Repeater?)
4) Wireless WDS Bridge
Desired Result:Simply extend the network. As a laptop is carried from room to room, laptop should switch to the strongest signal seamlessly, without user doing anything manually. No matter where I am, laptop should see entire network. Also, I prefer that the WAP not require a wired Ethernet connection (that is, I would like the WAP to receive/repeat the router's wireless signal No Ethernet Cable Required).
1. Which of the above 4 settings is best for achieving desired outcome?
2. What should the SSID be on the WAP? Same as on the router?
3. Should both the router and WAP be on the same channel? (I suspect not, but included docs sound like they should be..?)
4. Should both the router and the WAP have the same wireless security setting (WPA2) and pass phrase?
5. On the router, under the Wireless menu --> WDS sub menu there is a check box: "Allow wireless signal to be repeated by a repeater". I assume this must be checked?
6. I understand that Microsoft's built-in Wireless Zero Configuration service does not disambiguate APs which share the same SSID and may not always roam with the strongest signal.*** We need to move from area to area and seamlessly retain the network signal. Is this still a problem in Windows7? Is there a workaround for XP's WZC deficiencies?
Is there anything else I should know? [URL]
Whether the Linksys WRT300N wireless routers are compatible with LWAPP configuration?My school lab setup uses Cisco integrated services routers with NM-AIR-WLC6-K9 network modules as controllers in the LWAP network. The controller accepts configuration without error but does not pick up or seem to see the WRT300 AP routers, so cannot push out basic LWAP config info
View 1 Replies View RelatedI've just bought an AIR-WLC2106-K9 and 3 x AIR-LAP1142N-E-K9 and I'm having a problem getting the AP's configured.
Firstly, the controller did not discover the device when it was on the same sub net, I had to plug it straight in which is no good for wireless-n due to the 100Mbps port speed on the controller. Secondly, when I am editing the AP through the controller webpage, none of the details are saved after applying changes (static IP etc).
I followed the Cisco quick start guide for the controller to get the basic config, radius server details etc in. It is running software version: 4.2.61.0
I would like to provide WiFi in a big house of 4 floors so I have installed 1 WAP4410N wired to the Internet router to act as access point and I have configured 3 others WAP4410N as WDS repeater of the first one.In the first one (the AP), I have checked the option "Allow Wireless Signal to be repeated by a repeater" then entered the 3 repeaters' MAC addresses as allowed devices to repeat the signal.
Is that configuration OK ? Is there any way to add another (a fourth) repeater to this configuration ? Because there is only 3 fields to specify allowed repeaters' MAC addresses in the AP.
We have a couple of autonomous 1262's that I'd like to get configured. I would like to put the Ethernet interface out on our Internet subnet and have the clients get a RFC 1918 address from the radio's. Our little Linksys is setup this way and the clients are PAT'ing off the Ethernet interface when they go to the Internet.
Is this possible with these guys or do I have to put the AP ethernet interface into the same subnet with the DHCP scope? I don't have enough Internet IP's to hand out to every wireless client.
We got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. How to get cisco document to follow the steps if the above is doable,5508 is new with no setup.
View 6 Replies View Relatedconfiguration WAP4410n.I configure 1 wap4410n mode access point, is ok.I place 6 wap4410n in building as wireless repeater.I can not configure the right sequence.How do I set up 6 repeaters with access point ?
View 2 Replies View RelatedSomeone already do a bridge configuration with 1524 AP? I read Cisco documentation, and is not very clear regarding configuration on switch side.I will do a Bridge in trunking mode, so i want to know what is the VLAN i need to set as native vlan on the switch trunk port.Do i need to set the management vlan as native VLAN?
View 6 Replies View Related