We have a 1262 which was loaded with some recovery image for testing. After this, it doesn't get registered to the wireless controller.
we tried moving it back to autonomous mode and then again back to lightweight to have it join the controller. But it doesnt join the controller, debugs on the devices does not show any logs.
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies View RelatedWe have a few 1500 outdoor mesh ap's. 1262N are used to link to these 1500 and extend the coverage to places. All 1262 was configured as mesh. But upon installation, none of them actually register to the controller and join the other mesh ap's. They should be joining to the 1500's.
On testing, the 1500 joins the 1262N as mesh. however the 1262N does not join the 1500 as mesh even though the distance is less than 20m.
I'm trying to configure Cisco 1262 AP's to allow me to use the 2.4 gHz radio for client access and the 5.x radio for the repeater connection back to a root AP connected to a LAN.
I have already configured the AP's to associate with each other via the 5.x radio, and have a client connected to the repeater AP via the 2.4 gHz radio. From my laptop on the LAN, I can connect to the repeater AP, but I cannot ping nor otherwise communicate with the distant client.
When I use the 2.4 gHz radio for repeater mode, clients that connect to the repeater AP can be seen and communicated with.Is there something special that needs to be done to get my desired scenario to work?All radios are members of bridge group 1.
we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies View RelatedWhat is the maximum allowed number of wired clients behind a workgroup bridge? In other words, is there a limit on MAC addresses?I assume 1262 AP in WGB mode is connecting to a lighweight AP (1262 or 3502), latest IOS and WLC software. I wasn't able to find the answer from Cisco documentation.
View 2 Replies View RelatedAfter updating the firmware of th EA6500 to Ver.1.1.28.146072 I have no longer access to the GUI options of Speed Test, Guest Access, Parental Controls, Media Prioritization and USB Storage. I have reset the router to factory default settings and still none of the items are showing on the web page the only options available are:Connectivity,Troubleshooting.Wireless.
View 5 Replies View RelatedI have been using outlook for a while but I don't know what is offline or online mode.
View 1 Replies View RelatedI have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
I don't know if this is even possible, but can I change my wireless network card from 802.11b to 802.11g mode?
View 3 Replies View RelatedI'm trying to change the wireless security mode on my folks' WRT54G to see if I can get the wireless adapter on their new TIVO to talk to the router. It looks like TIVO only does WEP, not WPA. I get into the wireless page of the router and when I try selecting anything but "WPA Personal", the selected choice flips back to "WPA Personal" in less than a second. I've updated the firmware but no change.
View 9 Replies View RelatedTrying to secure Linksys WRT54G V8 wireless router. Can't change security mode from 'Disabled'!?
I followed this Post from EXPERT: "Connecting two routers wired - the definitive answer"
[url]...
I got the two routers working but the second one (not using it as a router) is not allowing me to change security mode from "disable" to WEP or anything else.The following Post didn't answered this issue: "Can't change wireless Security Mode on my WRT54G V5"
My WRT54G Router has been reset after severe weather conditions, the wireless in now unsecure. I am trying to change it back to secure mode under wireless / security wireless, but it does not allow me to do so. The security mode remains disabled and does not change to WEP or WPA.
View 2 Replies View RelatedThis is for a E1000 model router.I recently downloaded Cisco Connect. It wants my router name and password. I don't know the password. How can I find the password or change it? The password might still be the default, but "admin" does not work.
View 3 Replies View RelatedIn 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies View RelatedI recently received my Arris modem from comcast and during the installation phase I kept looking for an option to change the wifi mode from b/g/n to n only as all my network adapters connecting via wireless are n types and I want the max speed available from the modem. At no time did the option come up to define. So I finished the set-up and eveyone is connected, albeit at 54 Mpbs.I have accessed the modem via 10.0.0.1 after set-up in search of another option where I can revise the wifi mode. No luck. Comcast gave me the backhand lob over to Arris and Arris followed through with an overhead smash at the net.
View 4 Replies View Relatedit says that the cisco sg300-28 managed switch default system mode is Layer 2. but i want to change it to layer 3.
i can't get inside the "Console Interface Main Menu" where the switching from L2 to L3 will be done.
I have done the ff:
1. Upgraded firmware to 1.1.2.0 (latest)
2. Reset the switch to factory defaults.
3. The guide stated that in order to perform telnet to the switch, you need to enable it. So I logged in first in to the web GUI and enable telnet service.
4. I can now start telnet on the switch but I can't see the "Switch main menu".
All I can see are these lines from telnet:
User Name:cisco
Password:******
switchd5928c#
I just want to know how to get into the console interface main menu where these lines should appear so that i can change the system mode:
• System Configuration Menu
• Port Status
• Port Configuration
• System Mode
• Help
• Logout
My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing. When my client received their original switch back, I obviously brought my SF300-24 back to the workshop, reset it back to Factory defaults and tried to do a fresh installation on it. I can not get it to change from Layer 2 to Layer 3! I installed the latest firmware but still no go.
Everything works a 100% via the console, but when I go to the System Mode menu and try and edit it, it justs sits at layer 2 and will not chage to layer 3!
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
I am facing problem with 7600-ES+20G3C card / Any system reset will change the system operating mode
View 2 Replies View RelatedIs it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies View RelatedI have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies View RelatedI have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View RelatedI have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
is the aironet 1262 access point a good choice for an environment of about 20 users. each users is in an office and we are looking at deploying the ap at the end of the hall on a wall mount. would distance be a barrier and are there any better options out there?
View 3 Replies View RelatedI will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View RelatedI currently have WLC 5508 and a few campuses with LAP 1142, each with 2-3 vlan. Now one of our campuses have a building thas is a bit far away and needs network (wired). We can't get fiber or TP-cable there in a good way. So the plan is to get two 1262 or 3500 with AIR-ANT5160NP-R antennas and get a wireless link working between the campus and the building. And then connect one of the AP's to a switch in the other building to provide it with wired network.
The problem is that I can't find information on how to do it. Should both APs be in autonomus mode? I probably only need to have 1 VLAN in the other building but I am not sure yet. Is there a problem with transfering several VLAN over the WLAN-link?