Cisco WAN :: 7600-ES+20G3C Card - Warning / Any System Reset Will Change Operating Mode

Oct 14, 2012

I am facing problem with 7600-ES+20G3C card / Any system reset will change the system operating mode

View 2 Replies


ADVERTISEMENT

Reset Wireless Router After Rebooting Operating System?

Jun 12, 2012

I might have to reboot my operating system, I have a Cisco wireless router, so I have to reset it, and set it up again after i reboot my operating system?

View 8 Replies View Related

Cisco WAN :: 7609-S / 7600-ES+20G3C Not Working After IOS Upgrade

Oct 19, 2011

we have a problem with the ES+ card. After an IOS upgrade the card does not want to come online.The IOS version is 12.2(33)SRE4, it is the same problem with 12.2(33)SRE5.
 
I googled but could not much info. Only about %PM_SCP-SP-1-LCP_FW_ERR and the document said that the card should be inserted in an another slot, but it did not work. [code]

View 2 Replies View Related

Cisco Switches :: SF300-24 Can't Change To Layer 3 System Mode

Mar 16, 2012

My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing. When my client received their original switch back, I obviously brought my SF300-24 back to the workshop, reset it back to Factory defaults and tried to do a fresh installation on it. I can not get it to change from Layer 2 to Layer 3! I installed the latest firmware but still no go.
 
Everything works a 100% via the console, but when I go to the System Mode menu and try and edit it, it justs sits at layer 2 and will not chage to layer 3!

View 4 Replies View Related

Install A Form Of Operating System On HDD?

Nov 5, 2012

I was wondering if it is possible to install a certain operating system on a network HDD. any possible install a virtual machine or use that as a remote desktop to retrieve on a ipad.

View 1 Replies View Related

Cisco :: Operating System Support For CWLMS-4.0-100-K9?

Aug 24, 2011

I am getting following error during installation of LMS 4.0. ( "CWLMS-4.0-100-K9").I have installed SP1 for the Windows 2008 Standard R2, still getting same error.  Since Cisco's minimum requirement is Windows 2008 Standard and Enterprise with Service Pack 1 and Service Pack 2 (32 and 64 bit).

View 2 Replies View Related

Cabling / Cards :: Change Wireless Network Card From 802.11b To 802.11g Mode?

Sep 4, 2011

I don't know if this is even possible, but can I change my wireless network card from 802.11b to 802.11g mode?

View 3 Replies View Related

File Sharing Between XP And Windows 98 Operating System?

Sep 2, 2011

How to share files btween XP & Win98 operating systems , 2 towers

View 1 Replies View Related

Home Network :: Clear Operating System Firewall

Sep 16, 2012

I am redoing my homes networking and I am looking for a firewall. I heard that you can install clear os on a server and use it as a firewall and a dhcp server. So i was going to install it on a rack in my server cabinet. does the server need to have a wan port and a lan port? Or how does the server get connected? So, so far its the cable modem into the clear os firewall and then into my switch. Is is possible to use the clear os server as the dhcp server for the whole house? From the switch I am going to connect the rest of my servers, and the rest of the house. I was going to connect two wireless routers for my house. Would that work with the clear os server?

View 2 Replies View Related

Connect Belkin To Linux Mint 14 Operating System?

Jan 3, 2013

i am having trouble connecting my belkin router to my linux mint 14 operating system

View 1 Replies View Related

Cisco :: L-PI-1.1-CM-500 / Prime Infrastructure 1.x Server Requirements And Operating System?

Feb 2, 2013

I need to order LMS for one of our customer with 500 devices and reporting capabilities ..... So i chose base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and Compliance Management - 500 Device License "L-PI-1.1-CM-500"? i tried to search server capability for my requirements & Operating system and couldn't find it .....
 
1) What is the server requirements ?

2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)

3) Is their any dedicated appliance from Cisco ?

View 2 Replies View Related

Linksys Wireless Router :: E2500 Install Not Supported On Operating System

Sep 12, 2012

Im trying to install the e2500 router on my sisters macbook, but it says it is an "unsupported operating system". She has operating system 10.8.1. Why am i not able to install It?

View 1 Replies View Related

Linksys Wireless Adapters :: Wpc11ver.3 / Get Driver For Ubuntu Operating System?

Dec 22, 2012

wpc11ver.3 / get driver for Ubuntu operating system?

View 2 Replies View Related

Dell :: Dimension 2400 - Internet Connect-ability / New Operating System?

Aug 2, 2012

I just got my dell dimension 2400 up n running again.

1) I need a new operating system . i know how to do that what with windows being designed to make computers work properly or what is the latest thats not vista or could i just get a copy from a friend? <--- that may not be particularly legal but idc i just want to know if it would work if a new disk is too expensive  

2) I need internet connectability i have a working att wireless router brand new just got delivered today and i have a d link wireless reciever thing i just got from my buddy but how to get the internet up n running without boring holes in the floor / wall or dragging a cable 18 miles from the router to the computer so i need it to be wireless 

3) I am not sure what to do with it do i just need soft ware updates or do i need hardware updates to get it up to speed with the so called "big boys even though its far larger than any laptop my goal is to have a fast running internet capable game capable and multitasking computer with which i can do.

View 1 Replies View Related

Cisco WAN :: How To Know That 6500 And 7600 Series Switch And Router Are Running In Native Mode Or In Hybrid Mode

Feb 26, 2013

How can we know that 6500 and 7600 series switch and router are running in native mode or in hybrid mode.

View 2 Replies View Related

Cisco Switching/Routing :: WS-C2950-24 - What Last Reset From System-reset Means

Dec 10, 2012

Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?

View 3 Replies View Related

Cisco Wireless :: AP1262N-E-K9 Access Point With Firmware Version 12.4(25d)JA1 Operating In Autonomous Mode

Jan 10, 2013

we have a couple of AP1262N-E-K9 access point with firmware version 12.4(25d)JA1 operating in autonmous mode.
 
I attempted to measure the signal quality between the APs by setting one device to repeater mode while all others are in root mode. Then, I execute the following command: dot11 Dot11Radio 0 antenna-alignment
 
1. The output of "show dot11 antenna-alignment" is incorrect, the % value represents the signal strength in dBm without the - (minus). E.g. "-25 dBm" is displayed as "Signal 25% 0 dBm".Now, I know that is only a display error but still this is not clean. Is this a known issue?
 
2. Why are the measured signal strength values not displayed on the SSH console during the antenna-alignment test? Is it obligatory to use the console to see these values? Or is it also a known bug which might be fixed in later firmware versions?

View 2 Replies View Related

Cisco WAN :: 7600-SIP-200 Module In VSS Mode

Mar 26, 2011

if the  7600-SIP-200 supported in VSS mode or not ?
 
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
 
here is the show module output, after VSS conversion:
 
VSS1#show module Mod Ports Card Type                              Model              Serial No.--- ----- -------------------------------------- ------------------ -----------  1    0  4-subslot SPA Interface Processor-200  7600-SIP-200       JAE14500GMT  7    5  Supervisor Engine 720 10GE

[Code].....

View 1 Replies View Related

Cisco WAN :: 7600 Card Not Supporting Qinq

Dec 5, 2012

I want to do qinq on this card under its sub-interface, unfortanately it doesnt support the command as compared to other ES cards. [code]

View 3 Replies View Related

Cisco WAN :: 7600 Ethernet Service Plus Card - Model Difference

Mar 18, 2013

We are looking for buying a 20GE port 7600 ES+ Card. However, there are a  few different models, we are not sure which one is the right one. We  will be using this card for Metro Ethernet Termination, MPLS VPN,  EoMPLS, QoS (Marking, CBWFQ), PPPoE, possibly VPLS.

View 5 Replies View Related

Cisco WAN :: 7600 Router - Port Status Down When Using Transport Mode?

Dec 29, 2010

We have cisco 7600 Router with 76-ES+XT-4TG3C Module connected. The Module is getting detected after upgrading the Router with SRD5 IOS.Below are the testing which we have done on the Router but we are facing the issue while configuring the Transport mode LAN and Transport Mode WAN:Brief about this is:- 2 Cisco 7606-s Router with Module 76-ES+XT-4TG3C each.- two ports on 7606-s Ten2/1 & Ten2/2 are configured as a Transport mode WAN while Ten2/3 & Ten2/4 are configured as Transport mode LAN.- We connect Fiber Cable from LAN Port to MUX and from MUX to 2nd LAN Port of the same Router. Same thing we tested by using the WAN Port-MUX-WAN Port connection.- Now on MUX end LAN port, connected Single and Multi mode fiber and on 7606 end 2/4 port which is configured as transport mode LAN, using Multimode SFP module -> XFP-10G-MM-SR, port did not came up   then replaced 2/4 port with single mode SFP ->XFP-10GLR-OC192SR port came up. this is testing for LAN.-  For WAN testing on MUX end used WAN port and on 7606 end checked  with single mode and multimode fiber and with single XFP-10GLR-OC192SR / mulimode XFP-10G-MM-SR SFP, port did not come up.Wanted to know 1) If we have to go for Transport Mode LAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.2) If we have to go for Transport Mode WAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.Anything else is required while configuring the Transport Mode WAN as this is for Packet-Over_SONET/SDH? 3) MUX Side change is required while connecting both of this Modes on Cisco 7600 Router.4) Is hardware of the Router is giving any issue? Though we tested by connecting Back to Back LAN Port as well as Back to Back WAN Port. In both the situation the Ports are coming UP.

View 1 Replies View Related

Dell Inspiron 7600 / Realtek Wireless Card Not Working?

Feb 7, 2011

I recently bought a new Dell Inspiron 7600 pc running on windows 7 home premium and to enable access to our wireless internet I installed a Realtek 8185 wireless pci adaptor. It has worked fine (although not without the occasional blip) but recently it has stopped working. I could connect to our wireless network but connection came with a small exclamation mark on the wireless connection icon in the system tray. I tried reinstalling the most up to date drivers I could find on the realtek download website and this has removed the problem of the exclamation mark with the wireless connection claiming it now has internet access. However the internet is now so slow (vastly slower than before these problems began) I get timed out errors whenever I try to access any web pages. I have ruled out the router being an issue as my two housemates' computers are working just fine.

View 1 Replies View Related

Cisco Switching/Routing :: System Returned To ROM By Reset SP Error Of 7606-S

Jan 15, 2012

I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.

================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
  05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
 
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
 
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...

View 3 Replies View Related

Cisco :: Change The System Message For Each Ephone?

Aug 2, 2011

I'd like to know if it's possible to change the system message for each ephone independently with CME ?I mean, changing an ephone's system message without changing others' ones.

View 3 Replies View Related

PCI Wireless Card Causes System To Stutter?

Sep 25, 2011

My old system developed a stutter. It would freeze for a half-second at a time in short bursts. The stutter would appear off and on at random, and went on for a good year, coming and going. I couldn't locate the source, but it seemed to get worse when either the graphics card or the sound were called on heavily. Near the very end, the hard drive started getting corrupted, more and more swiftly. I had to replace my machine.So I created new, a fresh, home-built system:

* Asus P8 Z68-V motherboard
* Intel i5-2500k
* 16 GB RAM
* Radeon 6850
* 465 GB WD platter hd
* 128 GB SSD with a fresh install of Windows 7

After completing the installation of Windows, I brought over my old DVD drive, my old wireless card, and my old hard drive. I copied my old data to the new drive, and was relieved that I was able to do so successfully. Almost immediately, I began to get the stutter again! I did some troubleshooting, and discovered that the stutter went away when I pulled out my wireless card. I tried switching it to a different PCI slot, but the same thing continued. When I was able to test the machine with an ethernet cable plugged directly into a router, the stutter was gone. I bought a fresh wireless card, but the same thing happened immediately.

View 8 Replies View Related

Servers :: How To Change Name Of System Remotely

Jul 27, 2011

I work for a company that has several offices in various parts of the country, my job is to change the name of all the machines on our network to our new naming convention. I need to perform this task without causing a distrubance to the other users.

View 2 Replies View Related

System Won't Recognize Wireless Network Card?

Mar 13, 2012

Just built my new system and when I installed my network card drivers and utilities, a message comes up ASUS Wireless LAN card is taken apart from your desktop PC.

View 1 Replies View Related

Detect System Time Change On Network Workstation?

Dec 15, 2011

Is it possible to detect a system time change on a workstation on a network? There is suspicions that there is someone trying to use their system time as an excuse to go to lunch early at work, "but my computer says its 1 O'Clock" When everyone else's computer displays 12:48.......

View 1 Replies View Related

Cisco Switching/Routing :: 7010 - Lacp System Priority Change?

Jun 12, 2012

If after having an active peer-link port-channel between a couple of nexus 7010 I change lacp system-priority on both boxes and then I add a new member interface on that port-channel , that interface will be aligned with new lacp system-priority value but the old member do not and so I have to reload those modules which include old member interface.

View 1 Replies View Related

Dell :: Inspiron 5100 - Wireless Card Causes System To Lock Up

Dec 26, 2004

I have a wireless card that causes my Inspiron 5100 to lock up about once a day.  I have tried 3 different types of cards (Netgear, Microsoft, Dell) all with the same result.  I have a laptop cooler because I thought that the heat might be causing the problem - not the case.  If I leave the wireless card out the lockup does not happen. 
 
On a side note...I have tried to update the BIOS on my computer.  When I download what seems to be the appropriate file, it tells me that I don't have the appropriate file. 

View 20 Replies View Related

Linksys Wireless Router :: Wrt54gl / How To Change Security On System

Dec 25, 2011

I need to change how my security is set on my  wrt54gl... it has been so long I don't know the name or password I put it under.

View 1 Replies View Related

Cisco WAN :: Preventing Reset Into Express Mode On Catalyst 2960

Apr 21, 2008

Is there a way to prevent resetting catalyst config by pressing and holding in the MODE button after powerup? I had entered in a basic config into my switch including passwords, etc. and was checking out different uses of the MODE button including setting the switch into express mode and I somehow managed to wipe the config and send the switch back into a default state by holding the mode button in for too long.
 
I want to prevent this from happening once the switch it is in production.
 
Not sure if it matters, but this is the 24 S model using the LAN lite image..

View 3 Replies View Related

Cisco Infrastructure :: Reset 1252ag Access Point That Has Mode Button Disabled?

Apr 4, 2011

How do you reset a 1252ag access point that has the mode button disabled?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved